Outrigger Holder Reducer - 1-5/8" to 1-1/2" - Pair Downsize your outrigger holders Reduce from 1-5/8" to 1-1/2"

Outrigger Holder Reducer - 1-7/8" to 1-1/2" - Pair Downsize your outrigger holders Reduce from 1-7/8" to 1-1/2"

Outrigger Holder Reducer - 1-1/2" to 1-1/8" - Pair Downsize your outrigger holders Reduce from 1-1/2" to 1-1/8"

MX8000CR Adjustable Angle holders MX8000CR (1-5/8" ID) are our strongest and most versatile holders. The three-point mounting distributes the stress and provides side support. This heavy duty unit allows you to set your outrigger angle for maximum efficiency. The angle is set by positioning the clamp on the main tube during installation. The main tube of this unit is designed to accept the outrigger in either end so the holder can be mounted above or below any flat surface. A fast pin can be substituted for the bolt connecting the clamp to the wing for bridge laydown capability. Approximate area required for mounting is 14-1/2" x 18". Recommended poles for MX8000CR MX8719CR - 19 ft MX Step- Tube Style MX8716CX - 16 ft MX Step- Tube Style - Single Spreader MX8719CX - 19 ft MX Step- Tube Style - Single Spreader MX8720CX - 20 ft MX Step- Tube Style - Double Spreader MX8722CX - 22 ft MX Step- Tube Style - Single Spreader or Double Spreader

March MDX-3 5/8 Pump 115V Motor 5/8" Ports

March MDX 5/8 Pump 5/8" Ports 115V

Rod/Outrigger Holder - 1-5/8" x 16" x 1-1/2"- Pair Put absolutely no more holes in your T-Top or the gunnel of your boat. Simply place into your existing heavy duty cast stainless rod holder when outriggers are needed. When outriggers are not in use, simply remove holders and your existing cast rod holder is usable again.

9" Swivel Side Mount Rod Holder - 1-5/8" I.D. 316 Stainless Steel Designed for applications where clamp-on or flush mount holders are not practical Can be mounted on any vertical flat surface White vinyl insert included to protect your rod

9" Side Mount Rod Holder - 1-5/8" I.D. 316 Stainless Steel Designed for applications where clamp-on or flush mount holders are not practical Can be mounted on any vertical flat surface White vinyl insert included to protect your rod

Sealand 385310076 Duckbill Valve Set Black 1.5" (2Pak)

Brass Snap Shackle - Fixed Bail - 41.5mm(1-5/8") Length Features: Brass body and plunger pin Full release arm Heavy duty stainless steel plunger spring and precision components ensure dependable service Split ring on plunger pin for pull-line attachment

Bosworth 1.5 Inch Threaded Inlet Bronze  

Bosworth 1.5 Inch Threaded Oulet Bronze  

Welded Ring - 8mm(5/16") Thickness - 42.5mm(1-5/8") ID Round Welded Stainless Steel Ring 8mm(5/16") Thickness 42.5mm(1-5/8") Inner Diameter

Stainless Steel Clamp-On Rod Holder Stainless Steel Type 316 Polished Features and Benefits Adjustable clamp to fit multiple pipe and tube sizes For use on vertical and horizontal pipe/tube Rotate and lock in fishing angle Rotates and locks every 18° Form-fitted PVC White Liner Specifications: Clamp Fits (Outside Diameter):1-1/16" & 1-5/16" O.D. (Pipe), 1-1/4" O.D. (Tube) Location:T-Top Ring, Leaning Posts, Poling Platforms Rod Holder Inside Diameter: 1-5/8"