Rudder Anode Material: Zinc Outer Diameter: 5" Height: 0.89" Weight: 4.41lbs Full size and weight Rudder Each includes Stainless Steel hex nut and socket cap screw The captive hex nut is a great feature for underwater installations

Rudder Anode Material: Zinc Outer Diameter: 5" Height: 0.60" Weight: 3.10lbs Full size and weight Rudder Each includes Stainless Steel hex nut and socket cap screw The captive hex nut is a great feature for underwater installations

Impeller Kit - 10 Blade - Neoprene - 2" Diameter x 7/8"W Pin Drive Insert Material: Neoprene Insert Material:Brass Drive Type: Slotted Shaft Pin Drive or Through Hole Pin Drive Number of Blades: 10 Dimensions: Diameter:2" Shaft Width:1/2" Shaft Diameter:7/8" Jabsco flexible impellers can be fitted to most makes and models of bronze flexible impeller engine cooling, bilge, transfer and general purpose pumps. Jabsco flexible impellers are subjected to rigorous quality processes to ensure reliable, efficient and long lasting performance. Replace all impellers at least once every year, or sooner, depending on the engine duty. When the installation is correct an impeller may last for several years, but it is always advisable to stick to a schedule of preventative, rather than corrective, maintenance. Replacing impellers is easy. By removing the end cover screws, it is possible to remove the impeller by using either a Jabsco Impeller Removal Tool, or channel lock pliers, to grip the hub of the impeller. Don?t use screwdrivers as they may damage the face of the pump body, causing leaks, and they can be dangerous in confined spaces. Always carry spare impellers on board in case of emergency. The impeller is one of the most vital components of the engine cooling system and should always be treated as such. Always grease new impellers. Firstly, it makes it easier to install the impeller into the pump bore, and secondly it gives added protection to the impeller during initial prime. After replacing the gasket and end cover the pump is ready to use. WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

PED4900 PedestalPod Uncut (Usable Face = 12.5"W x 7.8"H) (31.75cm W x 19.8cm H) - Carbon Black PedestalPods are better than bracket mounting. Very sturdy and secure, yet clean and attractive, this mount provides protection of your fishfinder/chartplotter from the harshest of wet boating conditions. PedestalPods provide the convenience of easily reaching and controlling the fishfinder/chartplotter while providing added security with protection from theft. PedestalPods position your fishfinder/chartplotter at 20" off the deck and located near the bow and at the 45° angle for ease of viewing while fishing. This allows the user to easily reach and access the fishfinder/chartplotter for changes to range, zoom or even control the trolling motor. PedestalPods are manufactured with a double gasket system that provides an excellent watertight seal keeping spray off the electrical connections on the back of your fishfinder/chartplotter assuring reliability and longevity of your marine electronics. Your fishfinder/chartplotter is easily flush mounted into the pre-cut face of the NavPod. The heavy duty, powder coated aluminum pedestal tube is 3” in diameter with a 5” round base and has a large 1.75” opening providing plenty of room for running wires and connectors internally for a very clean look and provides protection for wires and electrical connectors from water intrusion, UV exposure or damage from just getting kicked or snagged and ripped out of their sockets. NavPods come with a security wrench and nickel chrome-plated stainless steel tamperproof screws for protection from theft. There are pre-cut models available for 7", 9" and 12" LCD displays from all major marine electronic manufacturers.

PP4900 PowerPod Uncut (Usable Face = 12.5"W x 7.8"H (31.75cm W x 19.8cm H) PowerPods are designed for the serious boater who is blasting offshore. He demands the most from his boat and his electronics. He needs a tough and rugged mount to protect vital electronics from the harshest of offshore boating conditions. Sturdy and secure, yet clean and attractive, PowerPods are better than bracket mounting. Over 70 Pre-Cut PowerPods are available for all popular manufacturers products. 1.8" opening in the swivel tube provides plenty of room for running wires and connectors through. PowerPods are positioned at a 20 degree tilt back viewing angle. PowerPods for Sail are for mounting on a flat surface. Perhaps under the dodger or aft end of the cockpit table especially on boats with dual wheels. Structural Rigidity The Gen3 enhancements now include a thicker gauge Acrylic Capped ABS material that improves strength and provides better structural rigidity. This thicker material allows for a larger waterproof seal. The better the structural rigidity, the less flexing when tightening and more uniform pressure on the seal. The excellent UV stability of the Acrylic is combined with the durability of the ABS. The Acrylic cap protects the ABS from UV and it's potentially damaging effects on plastic. These NavPods are really strong! Waterproof Seal All NavPods are manufactured with a double gasket system providing an excellent watertight seal between the front and back of the NavPod. This seal provides the best protection of your Marine Electronics. NavPods are made to withstand the harshest wet offshore boating conditions. Gen3 enhancements include a thicker external silicone gasket with improved flush fit. The internal Poran Microcell Polyurathane gasket is now 50% thicker and is not subject to "compression set" like many rubber compounds. This is important when you need to open the NavPod in the future in order to service your electronics. The gasket will continue to do its job.  Nickel Chrome Plated Stainless Steel NavPod uses all 316 stainless steel hardware that is supplied with each NavPod. Large round head tamperproof screws have deeper sockets for the NavPod wrench for better holding ability when tightening than screws used on our Traditional Series NavPod. For Gen3 NavPods we provide nickel chrome-plated stainless steel tamperproof screws for security combined with a little bling! Commitment to Quality We are committed to producing high quality Waterproof Housings for Marine Electronics. We stand behind our commitment by offering a 10-year warranty on all new Gen3 NavPods. We want you to be a NavPod customer for life and are willing to earn your trust and loyalty.

GP1900 SailPod Uncut (Usable Face = 12.5"W x 7.8"H) (31.8cm W x 1 9.8cm H) for 9.5" Wide Guard SailPods are for mounting a single Radar or Chartplotter at the helm. Navigation at your finger tips. "Where you need it...when you need it." Sail Pods are the smart solution for mounting your Radar or Chartplotter at the helm where you can easily operate and clearly see the fine details of the screen. NavPods have a high gloss finish, giving you a clean mounting solution while concealing unsightly wires. Nickel Chrome plated tamperproof screws provide a little bling and a lot of security. Designed with a double gasket waterproof seal, NavPods protect your electronics from the harshest of wet offshore boating conditions. A SailPod is best mounted on a Single Bend AngleGuard or use a Double Bend AngleGuard to fit an InstrumentPod on the top vertical section and SailPod below on the angled section. Structural Rigidity The Gen3 enhancements now include a thicker gauge Acrylic Capped ABS material that improves strength and provides better structural rigidity. This thicker material allows for a larger waterproof seal. The better the structural rigidity, the less flexing when tightening and more uniform pressure on the seal. The excellent UV stability of the Acrylic is combined with the durability of the ABS. The Acrylic cap protects the ABS from UV and it's potentially damaging effects on plastic. These NavPods are really strong! Waterproof Seal All NavPods are manufactured with a double gasket system providing an excellent watertight seal between the front and back of the NavPod. This seal provides the best protection of your Marine Electronics. NavPods are made to withstand the harshest wet offshore boating conditions. Gen3 enhancements include a thicker external silicone gasket with improved flush fit. The internal Poran Microcell Polyurathane gasket is now 50% thicker and is not subject to "compression set" like many rubber compounds. This is important when you need to open the NavPod in the future in order to service your electronics. The gasket will continue to do its job. Nickel Chrome Plated Stainless Steel We use all 316 stainless steel hardware that is supplied with each NavPod. Large round head tamperproof screws have deeper sockets for the NavPod wrench for better holding ability when tightening than screws used on our Traditional Series NavPod. For Gen3 NavPods we provide nickel chrome-plated stainless steel tamperproof screws for security combined with a little bling! Commitment to Quality We are committed to producing high quality Waterproof Housings for Marine Electronics. We stand behind our commitment by offering a 10-year warranty on all new Gen3 NavPods. We want you to be a NavPod customer for life and are willing to earn your trust and loyalty. SailPod for Power are for mounting on a SK135 Stachion Kit can be used to mount a SailPod on a flat surface, such as the flybridge. Stachion Kits can also be used with a SailPod for overhead mounting applications.

Rudder Anode Material: Magnesium Outer Diameter: 5" Height: 0.89" Weight: 1.11lbs Full size and weight Rudder Each includes Stainless Steel hex nut and socket cap screw The captive hex nut is a great feature for underwater installations

Rudder Anode Material: Zinc Outer Diameter: 2.84" Height: 0.43" Weight: 0.87lbs Full size and weight Rudder Each includes Stainless Steel hex nut and socket cap screw The captive hex nut is a great feature for underwater installations

Rudder Anode Material: Zinc Outer Diameter: 3.63" Height: 0.52" Weight: 1.56lbs Full size and weight Rudder Each includes Stainless Steel hex nut and socket cap screw The captive hex nut is a great feature for underwater installations

Rudder Anode Material: Zinc Outer Diameter: 1.85" Height: 0.28" Weight: 0.26lbs Full size and weight Rudder Each includes Stainless Steel hex nut and socket cap screw The captive hex nut is a great feature for underwater installations

Rudder Anode Material: Zinc Outer Diameter: 6-1/2" Height: 0.87" Weight: 8.79lbs Full size and weight Rudder Each includes Stainless Steel hex nut and socket cap screw The captive hex nut is a great feature for underwater installations

Tecnoseal Trim Plate Anode - Zinc Flat Mercury Alpha for Engines Plate for Trim Material: Zinc Pounds: 0.19 lbs Kg: 0,080 kg Height: 0.91"

Shaft Anode Material: Zinc Outer Diameter: 6.732" Inner Diameter: 5" Height: 3.504" Weight: 9.40lbs Holes: 4

Shaft Anode Material: Zinc Outer Diameter: 7.244" Inner Diameter: 5.50" Height: 3.504" Weight: 11.00lbs Holes: 4

Rudder Anode Material: Aluminum Outer Diameter: 5" Height: 0.89" Weight: 1.73lbs Full size and weight Rudder Each includes Stainless Steel hex nut and socket cap screw The captive hex nut is a great feature for underwater installations