Simnet Protection Plug

Simrad SimNet Product to NMEA 2000 Network Adapter Cable The Simrad SimNet Product to NMEA 2000® Network Adapter Cable, manufactured by Simrad, is used to connect a Simrad SimNet product like the NMEA 2000®/NMEA 0183 Adapter (AT10) or CX NavStation Series products to an NMEA 2000® network as shown in the following diagram. The cable is 0.5 meters in length and has a female SimNet connector on one end and a standard male NMEA 2000® Micro Series connector on the other end.

SimNet T Jointer - 3P Simrad SimNet T Jointer - 3PBrand NewThe Simrad 24005860 is a SimNet(Simrad Intelligent Marine Network) t jointer with 3 prong.

SimNet Starter Kit-1 Included: 24005845 SimNet 5M (16ft) cable 24006298 SimNet 7-Prong Multi-Joiner 24005894 SimNet Termination Plug 24005902 SimNet 2M (7ft) power cable with terminator

SimNet Cable 2M SimNet (Simrad Intelligent Marine Network) is a unique marine electronics network system. Over the last 5 years, it has proven to be one of the most reliable and easy to use networks in the marine industry. SimNet is easy to install with thin cables and small plugs.

SimNet Cable 1 Foot SimNet (Simrad Intelligent Marine Network) is a unique marine electronics network system. Over the last 5 years, it has proven to be one of the most reliable and easy to use networks in the marine industry. SimNet is easy to install with thin cables and small plugs.

SimNet Power Cable 2M with Terminator 2 Meter SimNet Power Cable with Terminator

Simnet 7 Prong Multi-Joiner

SimNet Joiner Yellow w/o Terminator

Edson International will introduce a new Radar, Satellite Antenna and Accessory Mounting System at the upcoming Miami Boatshow. Known as the Vision Series, the new product line delivers styling and design features unlike any mounting solution currently available. All-new sleek, modern design. First all modular system - extremely versatile. Easy to select and install for any radar, dome, light or camera combination. Easy to add accessories. Upgradable for future additions and modifications. Powder coated aluminum construction   Designed and manufactured at Edson's Massachusetts facility, the new towers provide a cost effective yet performance enhancing solution to mount the latest electronic radar & satellite domes, cameras, lights, and antennas on a wide range of power boats. A unique series of Mounting Plates allow the customer to mount any manufacturer's antenna on to any Edson Vision Series Tower, greatly simplifying the ordering process for the customer and stocking requirements for the dealer. The Vision Series towers will be available in single, dual and the first production triple mount configuration. Also available are standardized mounts to fit a wide range of products allowing electronics installers to stock a single product for multiple applications. "The Edson Vision Series is a stylistic departure from what our industry is used to seeing in an electronics mount,"says Rick Cowen, Product Manager for Edson's NavCom line. "These towers are really going to turn some heads and visually enhance the lines of powerboats, new and old."   See all Edson Products at Edson Marine ( http://www.clrmarine.com/462m4/manufacturers/edson-marine.html )   Vision Series mounts are available in a variety of standard and customized heights to fit most recreational powerboat designs. The unique Mounting Plates, Optional Antenna Wings, and Light Arms are easily added to the basic towers allowing a versatile, but simple installation for multiple antennas, receivers and lights. Custom height towers and configurations will also be available.   SEE THE EDSON VISION SERIES ELECTRONICS MOUNTING SYSTEM AT MIAMI BOATSHOW CONVENTION CENTER ELECTRONICS ROOM - BOOTH #1686

      Sprayway manufactures a complete line of industrial MRO, automotive, screen print and housekeeping products since 1947. Sprayway has been an innovative industry leader, and its Sprayway Glass Cleaner is recognized as "The World's Best." From marine detailing to industrial maintenance, whether it is a detailing wax or an industrial lubricant, Sprayway provides wide-ranging industries with the products they need.     The World's Best Glass Cleaner - Excellent for windows, mirrors, windshields and other glass surfaces! For cleaning and polishing glass, mirrors, windshields and windows. This easy-to use, fast acting product uses a clinging foam to break up soils and hold them - even on vertical surfaces. There is no dripping, no running and no streaking. With an exclusive formulation using denatured alcohol and no ammonia, this product cleans thoroughly, dries quickly, requires no rinsing and leaves a pleasant, fresh aroma.   SHOP: https://www.clrmarine.com/462m4/manufacturers/s/sprayway.html     Specials    Closeouts    Remanufactured    Rebates  

PP4406 PowerPod Pre-Cut for Simrad NSS7 evo2 or B&G Zeus² 7 PP4400 Series, PowerPods for Power are a better option than bracket mounting. PowerPods provide a clean look for flush mounting with the advantage of a swivel base. The trunion bracket that is supplied with most electronics is not optimal. PowerPods have the advantage of protecting the back of the electronics from harsh saltwater spray. Most manufacturers do an excellent job of protecting the face of the display from water intrusion with sealed rubber push buttons. The back is generally not waterproof. They are expecting you to flush mount it into the console or a NavPod. The PowerPod also protects the plastic connectors and wires from deterioration caused by long term exposure to UV. PowerPods for Sail are for mounting on a flat surface. Perhaps under the dodger or aft end of the cockpit table especially on boats with dual wheels. Sizing : Overall Size: 9"H x 10.2"W x 6"D Usable Face: 5.6"H x 8.9"W x 3.75"D Max Cutout: 4.625"H x 8"W All PowerPods Include Acrylic capped ABS plastic Chromed stainless steel tamper-poof fasteners Double seal for watertight integrity Models are available pre-cut for popular electronics Swivel Base with large pass-through for wire harness

PP5202 PowerPod Pre-Cut for Simrad NSS12 evo2 or B&G Zeus² 12 PP5200 Series, PowerPods for Power are a better option than bracket mounting. PowerPods provide a clean look for flush mounting with the advantage of a swivel base.The trunion bracket that is supplied with most electronics is not optimal. PowerPods have the advantage of protecting the back of the electronics from harsh saltwater spray. Most manufacturers do an excellent job of protecting the face of the display from water intrusion with sealed rubber push buttons. The back is generally not waterproof. They are expecting you to flush mount it into the console or a NavPod. The PowerPod also protects the plastic connectors and wires from deterioration caused by long term exposure to UV.PowerPods for Sail are for mounting on a flat surface. Perhaps under the dodger or aft end of the cockpit table especially on boats with dual wheels. Sizing : Usable Face: 9.85"H x 15.18"W All PowerPods Include Acrylic capped ABS plastic Chromed stainless steel tamper-poof fasteners Double seal for watertight integrity Models are available pre-cut for popular electronics Swivel Base with large pass-through for wire harness

PP5064 PowerPod Pre-Cut for Simrad NSE12/B&G Zeus 12 The PP5060 Series, PowerPods for Power are a better option than bracket mounting. PowerPods provide a clean look for flush mounting with the advantage of a swivel base. The trunion bracket that is supplied with most electronics is not optimal. PowerPods have the advantage of protecting the back of the electronics from harsh saltwater spray. Most manufacturers do an excellent job of protecting the face of the display from water intrusion with sealed rubber push buttons. The back is generally not waterproof. They are expecting you to flush mount it into the console or a NavPod. The PowerPod also protects the plastic connectors and wires from deterioration caused by long term exposure to UV. PowerPods for Sail are for mounting on a flat surface. Perhaps under the dodger or aft end of the cockpit table especially on boats with dual wheels. The Hi-Gloss Material NavPods are manufactured with a custom co-extruded acrylic capped ABS material. We use the absolute best UV resistant material that provides a very high gloss white finish that matches gel-coated fiberglass. The Gen3 enhancements now include a thicker gauge material that improves strength and provides for better structural rigidity. The Waterproof Seal All NavPods are manufactured with a double gasket system providing an excellent watertight seal between the front and back of the NavPod for protection of your Marine Electronics. NavPods are made to withstand the harshest of wet offshore boating conditions. Gen3 enhancements include a thicker external silicone gasket with improved flush fit. The internal EPDM gasket is now 50% thicker and is not subject to "compression set" like many rubber compounds. This is important when you need to open the NavPod in the future to service your electronics. The Nickel Chrome Plated Screws We use all stainless steel mounting hardware that is supplied with each NavPod. Large round head tamperproof screws have deeper sockets for the NavPod wrench for better holding ability when tightening than the previous screws. For Gen3 we provide nickel chrome-plated stainless steel tamperproof screws for security combined with a little bling! The Manufacturing Process Heavy-gauge thermoforming is considered an art since many processes come into play. It all starts with the design and development of the tooling. We are fortunate to have experienced in-house design engineers who utilize CAD programs like Solidworks, Catia and AutoCad. Surfcam is used to interface with our CNC machining centers to produce quality tools with precision tolerances. We have re-designed and re-tooled all of the popular NavPods. We have reviewed all of the former products and selected the best design elements of each and incorporated them in every new Gen3 product.

PP5059 PowerPod Pre-Cut for Simrad NSE8/B&G Zeus 8 The PP5050 Series, PowerPods for Power are a better option than bracket mounting. PowerPods provide a clean look for flush mounting with the advantage of a swivel base. The trunion bracket that is supplied with most electronics is not optimal. PowerPods have the advantage of protecting the back of the electronics from harsh saltwater spray. Most manufacturers do an excellent job of protecting the face of the display from water intrusion with sealed rubber push buttons. The back is generally not waterproof. They are expecting you to flush mount it into the console or a NavPod. The PowerPod also protects the plastic connectors and wires from deterioration caused by long term exposure to UV. PowerPods for Sail are for mounting on a flat surface. Perhaps under the dodger or aft end of the cockpit table especially on boats with dual wheels. The Hi-Gloss Material NavPods are manufactured with a custom co-extruded acrylic capped ABS material. We use the absolute best UV resistant material that provides a very high gloss white finish that matches gel-coated fiberglass. The Gen3 enhancements now include a thicker gauge material that improves strength and provides for better structural rigidity. The Waterproof Seal All NavPods are manufactured with a double gasket system providing an excellent watertight seal between the front and back of the NavPod for protection of your Marine Electronics. NavPods are made to withstand the harshest of wet offshore boating conditions. Gen3 enhancements include a thicker external silicone gasket with improved flush fit. The internal EPDM gasket is now 50% thicker and is not subject to "compression set" like many rubber compounds. This is important when you need to open the NavPod in the future to service your electronics. The Nickel Chrome Plated Screws We use all stainless steel mounting hardware that is supplied with each NavPod. Large round head tamperproof screws have deeper sockets for the NavPod wrench for better holding ability when tightening than the previous screws. For Gen3 we provide nickel chrome-plated stainless steel tamperproof screws for security combined with a little bling! The Manufacturing Process Heavy-gauge thermoforming is considered an art since many processes come into play. It all starts with the design and development of the tooling. We are fortunate to have experienced in-house design engineers who utilize CAD programs like Solidworks, Catia and AutoCad. Surfcam is used to interface with our CNC machining centers to produce quality tools with precision tolerances. We have re-designed and re-tooled all of the popular NavPods. We have reviewed all of the former products and selected the best design elements of each and incorporated them in every new Gen3 product.