|
ADAF2 Black Modular Top Plate for FLIR M100 or M200 Series Cameras for Use with Mounts Ending in M1 or M2
This Seaview top plate is for FLIR M100 or M200 thermal cameras. This one-piece design gives the top plate a nice clean look and is made from King Starboard.
|
192.00 |
|
|
Top Plate for FLIR M100 & M200
This Seaview top plate is for FLIR M100 or M200 thermal cameras. This one piece design gives the top plate a nice clean look, and is made from King Starboard.
|
192.00 |
|
|
Electrically Actuated Hinge 24V Fits Seaview Mounts Ending in M1 & M2
The Seaview SVEHB1 electrically actuated hinge will fit all Seaview mounts with 7"x7" and 10"x10" mounting base plates. Some electronics can also be mounted directly to the hinge plates when needed (contact Seaview to direct mount electronics). Professionally designed to raise and lower marine electronics with the push of a button. This single electrically actuated hinge will accommodate single small Seaview mounts up to large dual mounts fully loaded with marine electronics. This hinge is 5-9/16" tall x 13" wide x 20-1/2" long. This will hinge approximately 93 degrees leaving the hinge plate vertical off the mounting surface about 11-7/16".
This Seaview hinge is marine grade aluminum expertly fabricated for consistently superior welds. The actuator used is 24V however, 12V is an option with a conversion kit. The 24V actuator has a current draw of 10.4 amps on startup and when it is fully loaded with 2248 pound-force. The hinge has a very durable finish unlike anything else in the industry. This is first chem treated (for corrosion resistance), then an epoxy polyester primer coat is applied and finished with a polyester powder coat for a superior gloss white finish. There are two waterproof cable glands inside the hinge for water proof cable routing. This also has a removable lid to conveniently service the inside of the hinge if needed.
This actuated hinge has been used for many applications. Some examples, but not limited to are: Princess 66, Navetta 48, Sunseeker 52 & 66, Absolute 58, Sabre 45, Jupiter 27 and HCB Yacht 65CC.
Features:
Electrically Actuated Hinge
Volt: 24V
Fits Seaview Mounts ending M1 and M2
|
4752.00 |
|
|
ADAF3 Modular Top Plate for FLIR M300 Series Thermal Cameras f/Mounts Ending in M1 or M2
Seaview Modular Top Plates are designed to be mounted onto Seaview Modular Mounts. These Top Plates eliminate the "swiss cheese" look of most other radar and satdome mounts. With Seaview Top Plates the result is only four visible mounting screws to secure electronics.
Unique Design
No longer the unwanted “swiss cheese” look with a Seaview modular top plate. These plates result in only 4 visible mounting screws to secure electronics. A anodized 1/4" thick aluminum plate is pre-drilled to fit most marine electronics. This aluminum plate is then encased in a UV stable glass filled ABS white plastic. Each top plate is dimpled to match the provided drill templates for easy and precise drilling for your specific marine electronics.
Note: This only applies to the ADA-R1, ADA-S1 & ADA-S2 Top Plates
King Starboard
The ADA-R2, ADA-S3, ADA-S4 & ADA-F1 Top Plates are made of King Starboard. It comes pre-marked and supplied with a drill template. The end result is a clean looking installation.
|
192.00 |
|
|
Modular Top Plate for Flir M or Ray T Series Thermal Cameras
Seaview Modular Top Plates are designed to be mounted onto Seaview Modular Mounts. These Top Plates eliminate the "swiss cheese" look of most other radar and satdome mounts. With Seaview Top Plates the result is only four visible mounting screws to secure electronics.
King Starboard
Made of King Starboard. It comes pre-marked and supplied with a drill template. The end result is a clean looking installation.
|
196.80 |
|
|
Black Modular Plate for FLIR M300 Series Thermal Cameras for Mounts Ending in M1 or M2
Seaview Modular Top Plates are designed to be mounted onto Seaview Modular Mounts. These Top Plates eliminate the "swiss cheese" look of most other radar and satdome mounts. With Seaview Top Plates the result is only four visible mounting screws to secure electronics.
|
192.00 |
|
|
Modular Plate to Fit Searchlights & Thermal Cameras on Seaview Mounts Ending in M1 or M2
The Seaview ADABLANK is a universal modular top plate for mounting a searchlight or thermal camera for Seaview Modular Mounts ending in M1 or M2.
King Starboard
Top Plates are made of King Starboard. It comes pre-marked and supplied with a drill template. The end result is a clean-looking installation.
|
182.40 |
|
|
Camera Plate 2 for FLIR m100/200 Thermal Imaging Cameras
The modularDual Power Tower has been designed to allow your open array. radar, satdome and camera to be mounted together in one single space saving modular installation.
Specifically for Camera plate 2 (FLIR M100/200 Thermal Imaging Cameras)
|
152.56 |
|
|
Modular Plate to Fit Searchlights & Thermal Cameras on Seaview Mounts Ending in M1 or M2 - Black
The Seaview ADABLANKBLK is a universal modular top plate for mounting a searchlight or thermal camera for Seaview Modular Mounts ending in M1 or M2.
King Starboard
Top Plates are made of King Starboard. It comes pre-marked and supplied with a drill template. The result is a clean-looking installation.
|
201.60 |
|
|
5" Thermal Camera Mount f/FLIR M100 & M200 - 8" Round Base
Get the most out of your FLIR M100 or M200 camera with the Seaview PM5-FMH-8 camera mount. This mount will raise your camera 5.5" clearing anything that will obstruct your cameras view. The 8" diameter base takes up very little space making it a great solution for installations where space is limited. Four pre-drilled holes allows for simple and easy installation.
Extra Security
No visible bolts on the camera mounting plate provides extra security and improved aesthetics.
Small Base Foot Print
This mount is the perfect solution for installations where space is limited.
|
374.40 |
|
|
KVH V30 Modular Top Plate
Seaview Modular Top Plates are designed to be mounted onto Seaview Modular Mounts. These Top Plates eliminate the "swiss cheese" look of most other radar and satdome mounts. With Seaview Top Plates the result is only four visible mounting screws to secure electronics.
Compatible Units:
KVH V30
|
196.80 |
|
|
Modular Top Plate for Kymeta U8 Peregrine
Kymeta’s industry-leading, easily mountable, electronically steered antennas provide satellite and cellular connectivity where and when you need it. Seaview has partnered with Kymeta to provide this top plate mounting solution.
Features:
Designed specifically for the Kymeta Peregrine antenna
Specifications:
Mounting Type: Kymeta Modular Top Plate
Mount Style: Kymeta Top Plate for Seaview Mounts
|
470.40 |
|
|
ROKK Midi Top Plate f/Garmin and Raymarine
A multi-position, fully adjustable mount for small electronic devices. Install fish finders, chartplotters and other electronics on the dashboard, navigation station and various other desired locations.
The RL-502 is one (1) part of a system based around 4 different heavy-duty anodized aluminum mounts that allow your device to attach to the ROKK Midi to unlock its incredible features.
Features:
Engineered to withstand high shock loading.
Device-specific top plate
Technical Specifications:
Material - ASA Plastic
Dimensions (diameter) - 2.11" (53.8 mm)
Compatible with the following products
*Sold as an Individual
|
14.11 |
|
|
ROKK Midi Top Plate f/Humminbird and Raymarine
A multi-position, fully adjustable mount for small electronic devices. Install fish finders, chartplotters and other electronics on the dashboard, navigation station and various other desired locations.
The RL-506 is one (1) part of a system based around 4 different heavy-duty anodized aluminum mounts that allow your device to attach to the ROKK Midi to unlock its incredible features.
Features:
Engineered to withstand high shock loading.
Device-specific top plate
Technical Specifications:
Material - ASA Plastic
Dimensions (L x W) - 5.35" x 1.89" (136 x 48 mm)
Compatible with the following products
*Sold as an Individual
|
14.11 |
|
|
Complete Spreader Kit for Radar or Satdome Applications
This three piece kit consists of a mid section and two spreaders. Four bolts are used to secure each spreader to the midsection. The spreaders are tapered and angled aft so that for what ever you decide to put on there it will not interfere with the radar or satdome that you have on your mount. All the wiring from your GPS unit or antenna can be routed internally through the spreaders and into the mount itself. Not only does this help with security but it also makes for a very nice and clean installation. All the parts that make up the spreader kit are bolted together with rubber gaskets in between each part to prevent any water intrusion.
Spreader Kit Configurations
Closed dome radar - When you are using a closed dome radar with a spreader kit you want to raise your GPS units above the closed dome radar to avoid interference.
Satdome - If you are using a satdome you don’t need to use these extension posts with GPS units. Satdome radio waves travel up to the sky to the satellites, while the GPS waves will travel horizontally. Therefore you do not want these raised above your satellite dome.
*Used with Seaview mounts in which the part number ends in "M1"
|
561.60 |
|