A3 Downlight - Surface/Flush Mount - Stainless Steel This Scandvik A3 Surface Mounted LED Down Light is a single-color light. This A3 Surface Mount Series light features a snap-over bezel in Polished 316 stainless steel and a surface mount collar in a matching color. The A3 mounts securely overhead using two screws. Single-color lights have a two-wire (positive/negative) connection and work with a common switch (on/off).  Features: 316 stainless steel trim 6 x 0.5-watt warm white LED 242 Lumens 2.2 Watt 12 Volt   IP67 Applications: A3s are a good choice for general overhead lighting on smaller boats or as undercabinet lighting for any size vessel Other applications include hard tops, arches, walkway overhangs, shower stalls, or any area that lacks the depth to recess mount a fixture *The "P" within the part number indicates retail packaging

Engine Room Light - Surface/Flush Mount This super-bright, vibration-resistant LED light meets the expectations of next-generation vessels, refits, or upgrades. This multi-voltage fixture can be powered by your DC battery system, an AC generator/shore power, or both. If connected to both, the PC board automatically switches to DC power when AC power is lost.  Features: Includes a trim ring for surface mount installation and stainless steel mounting hardware Meets Requirements and Standards for SAE J1171 USCG, ABYC & NMMA IP67 Flush or Surface Mount Daylight  white (6000K) 168 super-bright 2835 LEDs 12/24 VDC and/or 110/220 VAC Specifications: Lumens: 3400 (similar to 2 x T8 fluorescents) Beam Angle: 120° Watts: 42 *The "P" within the part number indicates retail packaging

B3 Downlight Surface Mount - Cool White - SS Trim - IP67 - 12/24V Scandvik’s low profile B3 (3/8 in. height) surface-mounted, single-color downlight is manufactured to be simple and budget-friendly. The polished stainless steel snap-over trim ring is a nice upgrade from the inferior chrome plastic bezels of the past. The fixture is popular as a T-Top light because it looks like a flush-mount light without the hassle of cutting holes. Features: The light color is cool white 95 Lumens 10-30 VDC 1 Watt IP67 *The "P" within the part number indicates retail packaging

B3 Downlight Surface Mount - Blue - SS Trim - IP67 - 12/24V Scandvik’s low profile B3 (3/8 in. height) surface-mounted, single-color downlight is manufactured to be simple and budget-friendly. The polished stainless steel snap-over trim ring is a nice upgrade from the inferior chrome plastic bezels of the past. The fixture is popular as a T-Top light because it looks like a flush-mount light without the hassle of cutting holes. Features: The light color is blue 13 Lumens 10-30 VDC 1 Watt IP67 *The "P" within the part number indicates retail packaging

Flush Mount Spreader Light - 10-30V - White This is a flush-mount spreader light with white trim. Features: 12/24 V, 12W High-Quality Composition Frame Polycarbonate Lens UV Resistant Hidden Mounting Screws Cool white LED color (5,500 - 6,300K) Five 3 Watt Samsung 3535 LEDs 1,000 Lumens Equivalent to 120-watt halogen bulbs 0.8 Amp draw at 12 volts IP68 Specifications: Dimensions (W x H x D): 6 x 2-1/2 H x 1-3/4 in. Cutout (W x H): 4-1/2 x 1-1/2 in. LED Lifetime: 50,000 Hours LED Beam Angle: 110° The temperature of the LED: Less than 158° with a 77° ambient temperature *The "P" within the part number indicates retail packaging

PP4409 PowerPod Pre-Cut f/Garmin STRIKER™ 7sv/7dv 7" CHIRP Fishfinder (Requires Flush Mount Kit Garmin Part) PP4400 Series, PowerPods for Power are a better option than bracket mounting. PowerPods provide a clean look for flush mounting with the advantage of a swivel base. The trunion bracket that is supplied with most electronics is not optimal. PowerPods have the advantage of protecting the back of the electronics from harsh saltwater spray. Most manufacturers do an excellent job of protecting the face of the display from water intrusion with sealed rubber push buttons. The back is generally not waterproof. They are expecting you to flush mount it into the console or a NavPod. The PowerPod also protects the plastic connectors and wires from deterioration caused by long term exposure to UV. PowerPods for Sail are for mounting on a flat surface. Perhaps under the dodger or aft end of the cockpit table especially on boats with dual wheels. All PowerPods Include: Acrylic capped ABS plastic Chromed stainless steel tamper-poof fasteners Double seal for watertight integrity Models are available pre-cut for popular electronics Swivel Base with large pass-through for wire harness

PP4409 PowerPod Pre-Cut for Garmin STRIKER™ 7" 7sv/7dv (Requires Flush Mount Kit Garmin Part) - Carbon Black PP4400 Series, PowerPods for Power are a better option than bracket mounting. PowerPods provide a clean look for flush mounting with the advantage of a swivel base. The trunion bracket that is supplied with most electronics is not optimal. PowerPods have the advantage of protecting the back of the electronics from harsh saltwater spray. Most manufacturers do an excellent job of protecting the face of the display from water intrusion with sealed rubber push buttons. The back is generally not waterproof. They are expecting you to flush mount it into the console or a NavPod. The PowerPod also protects the plastic connectors and wires from deterioration caused by long term exposure to UV. PowerPods for Sail are for mounting on a flat surface. Perhaps under the dodger or aft end of the cockpit table especially on boats with dual wheels. All PowerPods Include: Acrylic capped ABS plastic Chromed stainless steel tamper-poof fasteners Double seal for watertight integrity Models are available pre-cut for popular electronics Swivel Base with large pass-through for wire harness

PP4410 PowerPod Pre-Cut for Garmin STRIKER™ 5dv (Requires Flush Mount Kit Garmin Part) PP4400 Series, PowerPods for Power are a better option than bracket mounting. PowerPods provide a clean look for flush mounting with the advantage of a swivel base. The trunion bracket that is supplied with most electronics is not optimal. PowerPods have the advantage of protecting the back of the electronics from harsh saltwater spray. Most manufacturers do an excellent job of protecting the face of the display from water intrusion with sealed rubber push buttons. The back is generally not waterproof. They are expecting you to flush mount it into the console or a NavPod. The PowerPod also protects the plastic connectors and wires from deterioration caused by long term exposure to UV. PowerPods for Sail are for mounting on a flat surface. Perhaps under the dodger or aft end of the cockpit table especially on boats with dual wheels. All PowerPods Include: Acrylic capped ABS plastic Chromed stainless steel tamper-poof fasteners Double seal for watertight integrity Models are available pre-cut for popular electronics Swivel Base with large pass-through for wire harness

PP4410 PowerPod Pre-Cut for Garmin STRIKER™ 5dv (Requires Flush Mount Kit Garmin Part) - Carbon Black PP4400 Series, PowerPods for Power are a better option than bracket mounting. PowerPods provide a clean look for flush mounting with the advantage of a swivel base. The trunion bracket that is supplied with most electronics is not optimal. PowerPods have the advantage of protecting the back of the electronics from harsh saltwater spray. Most manufacturers do an excellent job of protecting the face of the display from water intrusion with sealed rubber push buttons. The back is generally not waterproof. They are expecting you to flush mount it into the console or a NavPod. The PowerPod also protects the plastic connectors and wires from deterioration caused by long term exposure to UV. PowerPods for Sail are for mounting on a flat surface. Perhaps under the dodger or aft end of the cockpit table especially on boats with dual wheels. All PowerPods Include: Acrylic capped ABS plastic Chromed stainless steel tamper-poof fasteners Double seal for watertight integrity Models are available pre-cut for popular electronics Swivel Base with large pass-through for wire harness

LL-C 5" Flush Cover f/Globemaster, Super Yacht & SuperSport Flush Mount Compasses - White Protective cover for Globemaster, Super Yacht and SuperSport flush mount compasses (must have low level lighting). For: FB-500, SF-500, SS-5000, SS-5000W, SY-500LL, and SY-500LLC Approx. Shipping Weight: 1lb

Sure-Grip Flush Mount Mounting Base - Fits 2" Flat Surfaces This Attwood Sure-Grip Flush Mount can fit 2" flat surfaces and is constructed out of extruded aluminum.  Specifications: Base: Flush base Fits: 2” flat surfaces

Flush Mount Kit for echo™ 200, 500c & 550c Looking for a sleeker installation for your echo 200, 500c or 550c? A flush mount kit allows you to easily position your device against most flat surfaces in your boat. The kit includes a flush mount gasket, necessary hardware and instructions. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

D-Series PRO - Flush Mount - Diffused - Pair - Black One of RIGID's most versatile, compact lighting solutions just got better with the RIGID D-SS PRO, Dually-Side Shooter Professional Race Output LED pod. Perfect for any application that requires a wide spread beam, including A-Pillars, Fog Lights, and motorcycle applications. The D-SS PRO incorporates powerful optics and recently improved LED technology for greater output with the added benefit of additional LEDs aimed to the side for a much broader beam. The D-SS PRO packs a powerful punch with up to 102% more raw lumens depending on the optics chosen The D-SS PRO fixtures boast up to 120-degrees of horizontal lighting coverage when used in pairs or when used in the single light applications. The main forward-facing LEDs are available with RIGID's advanced Spot, Flood, or Driving optics, so there's a D-SS PRO lighting solution for nearly any application. The D-SS PRO LED lights are available in pairs with three side-shooting LEDs on one side of each fixture, or in single applications with a pair of side-shooting LEDs on both sides of the fixture. Only RIGID provides a broad, powerful lighting solution in such a compact package. Features: Optics: Hybrid - Diffused LED Color: White Finish Color: Black Mount Type: Flush Shipping Dimensions: 6" × 8" × 6" Product Weight: 2.46lb Sold As: Pair Hybrid Optics 60° Diffused Pattern 50,000+ Hr LED Lifespan Instant On / Off - No Warm Up RoHS Compliant Over / Under Voltage Protection Cast Aluminum Housing Durable Polycarbonate Lens Integrated Thermal Management GORE® Pressure Equalizing Vent Designed, Engineered, & Assembled in the USA Sealed Deutsch Connector Specifications: Watts: 30 Amp Draw: 2.14 LED's: 4 Raw Lumens: 3168 Lux @ 10m: 20.6 Beam Distance: 45.4 m Peak Beam Intensity: 2060 cd

SR-Q Series PRO Spot Diffused LED - Flush Mount - Pair - Black The SR-Q PRO is a sleek low profile lighting option that packs more lighting output than ever before thanks to recent improvements to the advanced LEDs inside. The SR-Q Professional Race Output now emits up to 102% more raw lumens, depending on optic. An excellent choice for any application where space is limited, the SR-Q PRO makes auxiliary lighting professional grade.  A single row of LEDs and is available in multiple beam patterns, including Spot, Flood, Driving, Hyperspot, and Diffused. Other recent updates to the SR-Q PRO include updated RIGID branding and blacked out circuit boards for a more refined look. Both surface and flush mount options are available and there are multiple mounting capabilities, such as the Suction Cup Mount and Angled Flush Mounts, just to name a few.  The SR-Q PRO is also a perfect back-up light and is available as a Back-Up Light Kit with a 25' harness and a three-position switch for ease of wiring and usage. Features: Optics: Spot - Diffused LED Color: White Finish Color: Black Mount Type: Flush Hybrid Optics 60° Diffused Pattern 50,000+ Hr LED Lifespan Instant On / Off - No Warm Up RoHS Compliant Over / Under Voltage Protection Cast Aluminum Housing Durable Polycarbonate Lens Integrated Thermal Management GORE® Pressure Equalizing Vent ∗ Sold as a Pair

Radiance Scene - RGBW - Flush Mount - Pair Radiance+ RBGW flush-mounted pod scene light provides a clean flush-mount option for the already epic light. The Radiance+ RGBW Pod Scene Light is built with the same high-grade aluminum alloy housing as our D-Series lights. The RGBW backlights provide the ability to toggle between eight available backlight options with the flip of a switch: red, green, blue, light blue, purple, amber, white, or demo mode. Utilizing the latest in LED technology and incorporating a thermally optimized heat sink, the Radiance+ RGBW Pod Scene Light provides up to 100 degrees of horizontal spread for maximum coverage. Scene lighting provides a clear, bright light with minimal amp draw. The Radiance+ RGBW Pod Scene Light is feature-packed, with a black exposed printed circuit board, forward-projecting optics that optimize the light output, and an integrated mounting plate that allows installers to mount the light flush with the chosen surface. The RIGID Radiance+ RGBW Pod Scene delivers a stylish approach to scene lighting. Features: 8 backlighting options (red, green, blue, light blue, purple, amber, white, or demo mode) Backlighting can be independently controlled using switch logic Black exposed printed circuit board 10-year warranty 9-15 V DC Black powder coat finish Pressure equalizing vent IP68 compliant - dust and water ingress High-grade aluminum alloy housing and heat sink Over/under voltage protection high-impact polycarbonate lens Mounting brackets are included RFI/EMI protection Rohs compliant Off-road use only Product Comes with: Two flush-mount scene Radiance+ RGBW light pods Mounting brackets Media pack Specifications: Size (inch): 3"  Weight (Lbs): 1.30 Optics: Scene light Watts: 24 Amp Draw: 1.7 Raw Lumens: 2970 Lux at 10m: 22 Beam Distance at 1Lux: 50 Beam Distance at .25 Lux: 93 Peak Beam Intensity (cd): 2166    Horizontal Beam Angle: 100