Engine Mount Kit - 4 Engine Mounts f/Small Yanmar Engines (Yanmar*) * Suitable for the Yanmar 1GM, 2GM, 3GM, 3YM, 3HM and 3JH series engines The R & D Marine Engine Mounts are designed specifically for the rigors of marine applications. The mounts are stiff enough to absorb forward and reverse propeller thrust, yet soft enough to isolate drivetrain vibrations from the hull. To help increase the longevity of the mounts, all steel parts are zinc plated and pasivated to limit corrosion. The rubber component is covered by an oil shield to protect it from petroleum based products. R & D Marine mounts are preloaded based on the combined engine and transmission weight to limit engine movement. To facilitate in the ease of installation the mounts are height adjusting and the mounting holes in the base of the mount are slotted to assist in alignment of the drivetrain. How To Select (details required): 1.Define the total weight of the engine and the transmission. 2.Determine 60% of the total weight and then divide by 2 to determine the capacity of each of the rear mounts (the mounts on the tranmission side of the engine). 3.Determine 40% of the total weight and then divide by 2 to determine the capacity of each of the front mounts (the mounts opposite the tranmission side of the engine). 4.Determine the stud necessary stud diameter and footprint of the mount. 5.Choose mount most appropriately sized for the per mount weight. When possible, choose the mount nearest the middle of the weight range. Example: Engine weight is 480lbs., transmission weight is 110lbs., footprint is 4", stud diameter is 5/8". Total weight is 590lbs. 590 x .6 / 2 = 177 lbs per rear mount. Mounts required are 800-010 590 x .4 / 2 = 118 lbs per rear mount. Mounts required are 800-037 Why R&D Marine Engine Mounts? Designed for marine use, accepts propeller and engine thrust in both directions Offers a fail safe design R & D Marine Mounts are height adjustable Pre-loaded to reduce movement Slotted holes in base to assist in alignment Mount types to fit all applications

Engine Mount w/4" Footprint - 5/8" Stud - 300lbs Capacity Per Mount The R & D Marine Engine Mounts are designed specifically for the rigors of marine applications. The mounts are stiff enough to absorb forward and reverse propeller thrust, yet soft enough to isolate drivetrain vibrations from the hull. To help increase the longevity of the mounts, all steel parts are zinc plated and pasivated to limit corrosion. The rubber component is covered by an oil shield to protect it from petroleum based products. R & D Marine mounts are preloaded based on the combined engine and transmission weight to limit engine movement. To facilitate in the ease of installation the mounts are height adjusting and the mounting holes in the base of the mount are slotted to assist in alignment of the drivetrain. How To Select (details required): 1.Define the total weight of the engine and the transmission. 2.Determine 60% of the total weight and then divide by 2 to determine the capacity of each of the rear mounts (the mounts on the tranmission side of the engine). 3.Determine 40% of the total weight and then divide by 2 to determine the capacity of each of the front mounts (the mounts opposite the tranmission side of the engine). 4.Determine the stud necessary stud diameter and footprint of the mount. 5.Choose mount most appropriately sized for the per mount weight. When possible, choose the mount nearest the middle of the weight range. Example: Engine weight is 480lbs., transmission weight is 110lbs., footprint is 4", stud diameter is 5/8". Total weight is 590lbs. 590 x .6 / 2 = 177 lbs per rear mount. Mounts required are 800-010 590 x .4 / 2 = 118 lbs per rear mount. Mounts required are 800-037 Why R&D Marine Engine Mounts? Designed for marine use, accepts propeller and engine thrust in both directions Offers a fail safe design R & D Marine Mounts are height adjustable Pre-loaded to reduce movement Slotted holes in base to assist in alignment Mount types to fit all applications

Engine Mount w/4" Footprint - 12mm Stud - 30-90lbs Capacity Per Mount The R & D Marine Engine Mounts are designed specifically for the rigors of marine applications. The mounts are stiff enough to absorb forward and reverse propeller thrust, yet soft enough to isolate drivetrain vibrations from the hull. To help increase the longevity of the mounts, all steel parts are zinc plated and pasivated to limit corrosion. The rubber component is covered by an oil shield to protect it from petroleum based products. R & D Marine mounts are preloaded based on the combined engine and transmission weight to limit engine movement. To facilitate in the ease of installation the mounts are height adjusting and the mounting holes in the base of the mount are slotted to assist in alignment of the drivetrain. How To Select (details required): 1.Define the total weight of the engine and the transmission. 2.Determine 60% of the total weight and then divide by 2 to determine the capacity of each of the rear mounts (the mounts on the tranmission side of the engine). 3.Determine 40% of the total weight and then divide by 2 to determine the capacity of each of the front mounts (the mounts opposite the tranmission side of the engine). 4.Determine the stud necessary stud diameter and footprint of the mount. 5.Choose mount most appropriately sized for the per mount weight. When possible, choose the mount nearest the middle of the weight range. Example: Engine weight is 480lbs., transmission weight is 110lbs., footprint is 4", stud diameter is 5/8". Total weight is 590lbs. 590 x .6 / 2 = 177 lbs per rear mount. Mounts required are 800-010 590 x .4 / 2 = 118 lbs per rear mount. Mounts required are 800-037 Why R&D Marine Engine Mounts? Designed for marine use, accepts propeller and engine thrust in both directions Offers a fail safe design R & D Marine Mounts are height adjustable Pre-loaded to reduce movement Slotted holes in base to assist in alignment Mount types to fit all applications

Engine Mount w/4" Footprint - 5/8" Stud - 70-201lbs Capacity Per Mount The R & D Marine Engine Mounts are designed specifically for the rigors of marine applications. The mounts are stiff enough to absorb forward and reverse propeller thrust, yet soft enough to isolate drivetrain vibrations from the hull. To help increase the longevity of the mounts, all steel parts are zinc plated and pasivated to limit corrosion. The rubber component is covered by an oil shield to protect it from petroleum based products. R & D Marine mounts are preloaded based on the combined engine and transmission weight to limit engine movement. To facilitate in the ease of installation the mounts are height adjusting and the mounting holes in the base of the mount are slotted to assist in alignment of the drivetrain. How To Select (details required): 1.Define the total weight of the engine and the transmission. 2.Determine 60% of the total weight and then divide by 2 to determine the capacity of each of the rear mounts (the mounts on the tranmission side of the engine). 3.Determine 40% of the total weight and then divide by 2 to determine the capacity of each of the front mounts (the mounts opposite the tranmission side of the engine). 4.Determine the stud necessary stud diameter and footprint of the mount. 5.Choose mount most appropriately sized for the per mount weight. When possible, choose the mount nearest the middle of the weight range. Example: Engine weight is 480lbs., transmission weight is 110lbs., footprint is 4", stud diameter is 5/8". Total weight is 590lbs. 590 x .6 / 2 = 177 lbs per rear mount. Mounts required are 800-010 590 x .4 / 2 = 118 lbs per rear mount. Mounts required are 800-037 Why R&D Marine Engine Mounts? Designed for marine use, accepts propeller and engine thrust in both directions Offers a fail safe design R & D Marine Mounts are height adjustable Pre-loaded to reduce movement Slotted holes in base to assist in alignment Mount types to fit all applications

Engine Mount w/4" Footprint - 5/8" Stud - 50-175lbs Capacity Per Mount The R & D Marine Engine Mounts are designed specifically for the rigors of marine applications. The mounts are stiff enough to absorb forward and reverse propeller thrust, yet soft enough to isolate drivetrain vibrations from the hull. To help increase the longevity of the mounts, all steel parts are zinc plated and pasivated to limit corrosion. The rubber component is covered by an oil shield to protect it from petroleum based products. R & D Marine mounts are preloaded based on the combined engine and transmission weight to limit engine movement. To facilitate in the ease of installation the mounts are height adjusting and the mounting holes in the base of the mount are slotted to assist in alignment of the drivetrain. How To Select (details required): 1.Define the total weight of the engine and the transmission. 2.Determine 60% of the total weight and then divide by 2 to determine the capacity of each of the rear mounts (the mounts on the tranmission side of the engine). 3.Determine 40% of the total weight and then divide by 2 to determine the capacity of each of the front mounts (the mounts opposite the tranmission side of the engine). 4.Determine the stud necessary stud diameter and footprint of the mount. 5.Choose mount most appropriately sized for the per mount weight. When possible, choose the mount nearest the middle of the weight range. Example: Engine weight is 480lbs., transmission weight is 110lbs., footprint is 4", stud diameter is 5/8". Total weight is 590lbs. 590 x .6 / 2 = 177 lbs per rear mount. Mounts required are 800-010 590 x .4 / 2 = 118 lbs per rear mount. Mounts required are 800-037 Why R&D Marine Engine Mounts? Designed for marine use, accepts propeller and engine thrust in both directions Offers a fail safe design R & D Marine Mounts are height adjustable Pre-loaded to reduce movement Slotted holes in base to assist in alignment Mount types to fit all applications

Engine Mount w/4" Footprint - 5/8" Stud - 80-230lbs Capacity Per Mount The R & D Marine Engine Mounts are designed specifically for the rigors of marine applications. The mounts are stiff enough to absorb forward and reverse propeller thrust, yet soft enough to isolate drivetrain vibrations from the hull. To help increase the longevity of the mounts, all steel parts are zinc plated and pasivated to limit corrosion. The rubber component is covered by an oil shield to protect it from petroleum based products. R & D Marine mounts are preloaded based on the combined engine and transmission weight to limit engine movement. To facilitate in the ease of installation the mounts are height adjusting and the mounting holes in the base of the mount are slotted to assist in alignment of the drivetrain. How To Select (details required): 1.Define the total weight of the engine and the transmission. 2.Determine 60% of the total weight and then divide by 2 to determine the capacity of each of the rear mounts (the mounts on the tranmission side of the engine). 3.Determine 40% of the total weight and then divide by 2 to determine the capacity of each of the front mounts (the mounts opposite the tranmission side of the engine). 4.Determine the stud necessary stud diameter and footprint of the mount. 5.Choose mount most appropriately sized for the per mount weight. When possible, choose the mount nearest the middle of the weight range. Example: Engine weight is 480lbs., transmission weight is 110lbs., footprint is 4", stud diameter is 5/8". Total weight is 590lbs. 590 x .6 / 2 = 177 lbs per rear mount. Mounts required are 800-010 590 x .4 / 2 = 118 lbs per rear mount. Mounts required are 800-037 Why R&D Marine Engine Mounts? Designed for marine use, accepts propeller and engine thrust in both directions Offers a fail safe design R & D Marine Mounts are height adjustable Pre-loaded to reduce movement Slotted holes in base to assist in alignment Mount types to fit all applications

Engine Mount w/4" Footprint - 5/8" Stud - 120-410lbs Capacity Per Mount The R & D Marine Engine Mounts are designed specifically for the rigors of marine applications. The mounts are stiff enough to absorb forward and reverse propeller thrust, yet soft enough to isolate drivetrain vibrations from the hull. To help increase the longevity of the mounts, all steel parts are zinc plated and pasivated to limit corrosion. The rubber component is covered by an oil shield to protect it from petroleum based products. R & D Marine mounts are preloaded based on the combined engine and transmission weight to limit engine movement. To facilitate in the ease of installation the mounts are height adjusting and the mounting holes in the base of the mount are slotted to assist in alignment of the drivetrain. How To Select (details required): 1.Define the total weight of the engine and the transmission. 2.Determine 60% of the total weight and then divide by 2 to determine the capacity of each of the rear mounts (the mounts on the tranmission side of the engine). 3.Determine 40% of the total weight and then divide by 2 to determine the capacity of each of the front mounts (the mounts opposite the tranmission side of the engine). 4.Determine the stud necessary stud diameter and footprint of the mount. 5.Choose mount most appropriately sized for the per mount weight. When possible, choose the mount nearest the middle of the weight range. Example: Engine weight is 480lbs., transmission weight is 110lbs., footprint is 4", stud diameter is 5/8". Total weight is 590lbs. 590 x .6 / 2 = 177 lbs per rear mount. Mounts required are 800-010 590 x .4 / 2 = 118 lbs per rear mount. Mounts required are 800-037 Why R&D Marine Engine Mounts? Designed for marine use, accepts propeller and engine thrust in both directions Offers a fail safe design R & D Marine Mounts are height adjustable Pre-loaded to reduce movement Slotted holes in base to assist in alignment Mount types to fit all applications

Engine Mount w/4" Footprint - 5/8" Stud - 300-680lbs Capacity Per Mount The R & D Marine Engine Mounts are designed specifically for the rigors of marine applications. The mounts are stiff enough to absorb forward and reverse propeller thrust, yet soft enough to isolate drivetrain vibrations from the hull. To help increase the longevity of the mounts, all steel parts are zinc plated and pasivated to limit corrosion. The rubber component is covered by an oil shield to protect it from petroleum based products. R & D Marine mounts are preloaded based on the combined engine and transmission weight to limit engine movement. To facilitate in the ease of installation the mounts are height adjusting and the mounting holes in the base of the mount are slotted to assist in alignment of the drivetrain. How To Select (details required): 1.Define the total weight of the engine and the transmission. 2.Determine 60% of the total weight and then divide by 2 to determine the capacity of each of the rear mounts (the mounts on the tranmission side of the engine). 3.Determine 40% of the total weight and then divide by 2 to determine the capacity of each of the front mounts (the mounts opposite the tranmission side of the engine). 4.Determine the stud necessary stud diameter and footprint of the mount. 5.Choose mount most appropriately sized for the per mount weight. When possible, choose the mount nearest the middle of the weight range. Example: Engine weight is 480lbs., transmission weight is 110lbs., footprint is 4", stud diameter is 5/8". Total weight is 590lbs. 590 x .6 / 2 = 177 lbs per rear mount. Mounts required are 800-010 590 x .4 / 2 = 118 lbs per rear mount. Mounts required are 800-037 Why R&D Marine Engine Mounts? Designed for marine use, accepts propeller and engine thrust in both directions Offers a fail safe design R & D Marine Mounts are height adjustable Pre-loaded to reduce movement Slotted holes in base to assist in alignment Mount types to fit all applications

Engine Mount w/4" Footprint - 3/4" Stud - 250-563lbs Capacity Per Mount The R & D Marine Engine Mounts are designed specifically for the rigors of marine applications. The mounts are stiff enough to absorb forward and reverse propeller thrust, yet soft enough to isolate drivetrain vibrations from the hull. To help increase the longevity of the mounts, all steel parts are zinc plated and pasivated to limit corrosion. The rubber component is covered by an oil shield to protect it from petroleum based products. R & D Marine mounts are preloaded based on the combined engine and transmission weight to limit engine movement. To facilitate in the ease of installation the mounts are height adjusting and the mounting holes in the base of the mount are slotted to assist in alignment of the drivetrain. How To Select (details required): 1.Define the total weight of the engine and the transmission. 2.Determine 60% of the total weight and then divide by 2 to determine the capacity of each of the rear mounts (the mounts on the tranmission side of the engine). 3.Determine 40% of the total weight and then divide by 2 to determine the capacity of each of the front mounts (the mounts opposite the tranmission side of the engine). 4.Determine the stud necessary stud diameter and footprint of the mount. 5.Choose mount most appropriately sized for the per mount weight. When possible, choose the mount nearest the middle of the weight range. Example: Engine weight is 480lbs., transmission weight is 110lbs., footprint is 4", stud diameter is 5/8". Total weight is 590lbs. 590 x .6 / 2 = 177 lbs per rear mount. Mounts required are 800-010 590 x .4 / 2 = 118 lbs per rear mount. Mounts required are 800-037 Why R&D Marine Engine Mounts? Designed for marine use, accepts propeller and engine thrust in both directions Offers a fail safe design R & D Marine Mounts are height adjustable Pre-loaded to reduce movement Slotted holes in base to assist in alignment Mount types to fit all applications

Engine Mount w/6.85" Footprint - 5/8" Stud - 50-75lbs Capacity Per Mount *Suitable for the Yanmar 1GM, 2GM, 3GM, 3YM, 3HM and 3JH series engines The R & D Marine Engine Mounts are designed specifically for the rigors of marine applications. The mounts are stiff enough to absorb forward and reverse propeller thrust, yet soft enough to isolate drivetrain vibrations from the hull. To help increase the longevity of the mounts, all steel parts are zinc plated and pasivated to limit corrosion. The rubber component is covered by an oil shield to protect it from petroleum based products. R & D Marine mounts are preloaded based on the combined engine and transmission weight to limit engine movement. To facilitate in the ease of installation the mounts are height adjusting and the mounting holes in the base of the mount are slotted to assist in alignment of the drivetrain. How To Select (details required): 1.Define the total weight of the engine and the transmission. 2.Determine 60% of the total weight and then divide by 2 to determine the capacity of each of the rear mounts (the mounts on the tranmission side of the engine). 3.Determine 40% of the total weight and then divide by 2 to determine the capacity of each of the front mounts (the mounts opposite the tranmission side of the engine). 4.Determine the stud necessary stud diameter and footprint of the mount. 5.Choose mount most appropriately sized for the per mount weight. When possible, choose the mount nearest the middle of the weight range. Example: Engine weight is 480lbs., transmission weight is 110lbs., footprint is 4", stud diameter is 5/8". Total weight is 590lbs. 590 x .6 / 2 = 177 lbs per rear mount. Mounts required are 800-010 590 x .4 / 2 = 118 lbs per rear mount. Mounts required are 800-037 Why R&D Marine Engine Mounts? Designed for marine use, accepts propeller and engine thrust in both directions Offers a fail safe design R & D Marine Mounts are height adjustable Pre-loaded to reduce movement Slotted holes in base to assist in alignment Mount types to fit all applications

Engine Mount w/6.85" Footprint - 5/8" Stud - 80-230lbs Capacity Per Mount ** Designed as a front mount for the Yanmar 4JH series engine The R & D Marine Engine Mounts are designed specifically for the rigors of marine applications. The mounts are stiff enough to absorb forward and reverse propeller thrust, yet soft enough to isolate drivetrain vibrations from the hull. To help increase the longevity of the mounts, all steel parts are zinc plated and pasivated to limit corrosion. The rubber component is covered by an oil shield to protect it from petroleum based products. R & D Marine mounts are preloaded based on the combined engine and transmission weight to limit engine movement. To facilitate in the ease of installation the mounts are height adjusting and the mounting holes in the base of the mount are slotted to assist in alignment of the drivetrain. How To Select (details required): 1.Define the total weight of the engine and the transmission. 2.Determine 60% of the total weight and then divide by 2 to determine the capacity of each of the rear mounts (the mounts on the tranmission side of the engine). 3.Determine 40% of the total weight and then divide by 2 to determine the capacity of each of the front mounts (the mounts opposite the tranmission side of the engine). 4.Determine the stud necessary stud diameter and footprint of the mount. 5.Choose mount most appropriately sized for the per mount weight. When possible, choose the mount nearest the middle of the weight range. Example: Engine weight is 480lbs., transmission weight is 110lbs., footprint is 4", stud diameter is 5/8". Total weight is 590lbs. 590 x .6 / 2 = 177 lbs per rear mount. Mounts required are 800-010 590 x .4 / 2 = 118 lbs per rear mount. Mounts required are 800-037 Why R&D Marine Engine Mounts? Designed for marine use, accepts propeller and engine thrust in both directions Offers a fail safe design R & D Marine Mounts are height adjustable Pre-loaded to reduce movement Slotted holes in base to assist in alignment Mount types to fit all applications

Engine Mount w/6.85" Footprint - 5/8" Stud - 120-410lbs Capacity Per Mount *** Designed as a rear mount for the Yanmar 4JH series engine The R & D Marine Engine Mounts are designed specifically for the rigors of marine applications. The mounts are stiff enough to absorb forward and reverse propeller thrust, yet soft enough to isolate drivetrain vibrations from the hull. To help increase the longevity of the mounts, all steel parts are zinc plated and pasivated to limit corrosion. The rubber component is covered by an oil shield to protect it from petroleum based products. R & D Marine mounts are preloaded based on the combined engine and transmission weight to limit engine movement. To facilitate in the ease of installation the mounts are height adjusting and the mounting holes in the base of the mount are slotted to assist in alignment of the drivetrain. How To Select (details required): 1.Define the total weight of the engine and the transmission. 2.Determine 60% of the total weight and then divide by 2 to determine the capacity of each of the rear mounts (the mounts on the tranmission side of the engine). 3.Determine 40% of the total weight and then divide by 2 to determine the capacity of each of the front mounts (the mounts opposite the tranmission side of the engine). 4.Determine the stud necessary stud diameter and footprint of the mount. 5.Choose mount most appropriately sized for the per mount weight. When possible, choose the mount nearest the middle of the weight range. Example: Engine weight is 480lbs., transmission weight is 110lbs., footprint is 4", stud diameter is 5/8". Total weight is 590lbs. 590 x .6 / 2 = 177 lbs per rear mount. Mounts required are 800-010 590 x .4 / 2 = 118 lbs per rear mount. Mounts required are 800-037 Why R&D Marine Engine Mounts? Designed for marine use, accepts propeller and engine thrust in both directions Offers a fail safe design R & D Marine Mounts are height adjustable Pre-loaded to reduce movement Slotted holes in base to assist in alignment Mount types to fit all applications

5309-R 23' Galaxy VHF Antenna THIS PRODUCT MUST SHIP TRUCK FREIGHT AND DOES NOT QUALIFY FOR ANY SHIPPING PROMOTIONS Phased 1/2 wave elements in collinear array with a band spread matching sleeve and a choking stub to suppress cable radiation This design invokes all the antenna engineers tricks to produce the clearest possible transmission and reception over the longest range. Features: Brass and copper elements Stainless steel ferrule with standard 1"-14 thread Includes 20' RG-8/X cable and a PL-259 connector Suggested mount: Shakespeare Style 409-R or 410-R Mounting Kit (pictured mount not included) Two sections: Base 172", Tip 105" Twin to: Galaxy Style 5310-A HF/SSB Shakespeare Limited Warranty: 5 years Includes FME Cables Technical Specifications: Frequency: VHF Marine Band Bandwidth: 5 MHz within 2.0:1 VSWR SWR: nominally 1.5:1 at 156.8 MHz Gain: 9 dB Max Input (Watts): 150 watts DC Ground: NO Height (feet): 23' Polarization: Vertical

Major Rebuild Kit for Sherwood R-30-G-1 This kit contains the following items   GY 211P-2 1 SQ-HD-PLUG 1/8-B JA 11847-0000 1 KEY MS DATA SHEET 1 DATA SHEET SH 04303 1 SNAP RING SH 10077K 1 IMPELLER KIT SH 10093 1 KEY-WOODRUFF SH 10195 1 SCREW SH 10197 1 VELLUMOID 505 FIBRE GASKET SH 10281 1 COVER ASSEMBLY SH 10285 1 CAM SH 11367 1 SEAL/SEAT ASSEMBLY SH 12686 6 SLOTTED MACH SCREW 10-24 SH 1311 2 DOWELL PIN SH 343 8 LOCKWASHER SH 4304 3 SNAP RING SH 4306 1 BALL BEARING SH 5437 2 SCREW     Kits are put together at time of order

Minor Repair Kit for Sherwood R-30-G-1 This kit contains the following items   SH 10077K 1 IMPELLER KIT SH 11367 1 SEAL/SEAT ASSEMBLY     Kits are put together at time of order