BI-200 Battery Integrator Charging multiple battery banks without the use of diode isolators dictates that the batteries be connected or “integrated” only whenever a charge voltage is present so that they may be charged simultaneously, then disconnected or “isolated” when the charge voltage is no longer present to allow for selective discharge and avoid having the secondary or standby battery drain into the primary battery. Battery integrators perform this function automatically, acting as a “smart” switch to connect independent battery banks only when a charging voltage is present. Otherwise, they are isolated, and discharge between banks is prevented. The Battery Integrator causes no voltage drop in the charging system, while the multiple batteries are charged as a single bank whenever a charging source of approximately 13.2 VDC or 26.4 VDC or greater is present (depending on the model). When the alternator or charger is off or a large load causes the voltage to drop below the disconnect point, the unit breaks the common tie between the banks. This allows selective battery discharge and prevents the “dumping” of a higher-charged bank into a lower-charged bank. The unit may also be remotely activated to connect other batteries through the key starter or a manual switch to provide an added “boost” from the secondary battery whenever the starter is engaged and the unit senses there is sufficient voltage in that battery to provide an assist. Features: Enables charging of two separate banks without voltage drop yet maintains 100% isolation at all other times. For systems of three banks or more, an additional unit must be installed for each additional bank Heavy-duty silver-plated contactor, continuous duty rated to 100 Amps or 200 Amps depending on model Voltage sense circuits, epoxy-encapsulated, and heavy-duty continuous-rated solenoids are all designed for use in marine environments Has ignition protection rating Easy three-wire hookup for two bank systems (BATT +, BATT +, GROUND) Terminal for optional wiring of a remote light indicating when battery banks are integrated Optional internal connections can be wired through the key starter or manual override switch, tying battery banks together for an extra boost during engine start Specifications: Terminals: Battery Connections: 5/16 in. copper alloy stud Approvals: CE Marked Dimensions (H x W x D): 200 Amp Models: 4 x 3.3 x 4.1 inches Weight: 2 lb. Operating Temperature: Control: -40 to +85 degrees C and Solenoid: -28 to +48 degrees C Voltage: 12 VDC Battery Integration Point: 13.2 VDC     Battery Disconnect Point: 12.8 VDC Max. Continuous Current: 200 Amps     Peak Maximum Current: 600 Amps

BI-100 Battery Integrator Charging multiple battery banks without the use of diode isolators dictates that the batteries be connected or “integrated” only whenever a charge voltage is present so that they may be charged simultaneously, then disconnected or “isolated” when the charge voltage is no longer present to allow for selective discharge and avoid having the secondary or standby battery drain into the primary battery. Battery integrators perform this function automatically, acting as a “smart” switch to connect independent battery banks only when a charging voltage is present. Otherwise, they are isolated, and discharge between banks is prevented. The Battery Integrator causes no voltage drop in the charging system, while the multiple batteries are charged as a single bank whenever a charging source of approximately 13.2 VDC or 26.4 VDC or greater is present (depending on the model). When the alternator or charger is off or a large load causes the voltage to drop below the disconnect point, the unit breaks the common tie between the banks. This allows selective battery discharge and prevents the “dumping” of a higher-charged bank into a lower-charged bank. The unit may also be remotely activated to connect other batteries through the key starter or a manual switch to provide an added “boost” from the secondary battery whenever the starter is engaged and the unit senses there is sufficient voltage in that battery to provide an assist. Features: Enables charging of two separate banks without voltage drop yet maintains 100% isolation at all other times. For systems of three banks or more, an additional unit must be installed for each additional bank Heavy-duty silver-plated contactor, continuous duty rated to 100 Amps or 200 Amps depending on model Voltage sense circuits, epoxy-encapsulated, and heavy-duty continuous-rated solenoids are all designed for use in marine environments 12 volt, 100 amp model has an ignition protection rating Has ignition protection rating Easy three-wire hookup for two bank systems (BATT +, BATT +, GROUND) Terminal for optional wiring of a remote light indicating when battery banks are integrated Optional internal connections can be wired through the key starter or manual override switch, tying battery banks together for an extra boost during engine start Specifications: Terminals: Battery Connections: 5/16 in. copper alloy stud Approvals: CE Marked Dimensions (H x W x D): 100 Amp Models: 3 x 3.25 x 2.5 inches Weight: 1 lb. Operating Temperature: Control: -40 to +85 degrees C and Solenoid: -28 to +48 degrees C Voltage: 12 VDC Battery Integration Point: 13.2 VDC     Battery Disconnect Point: 12.8 VDC Max. Continuous Current: 100 Amps     Peak Maximum Current: 400 Amps

PT-7 Battery Charger Newmar’s Phase Three Series Battery Chargers employ “Smart” battery charging technology for 12-volt systems aboard marine applications including workboats, military vessels, commercial vessels, and recreational craft. This charger interacts with batteries, providing the optimum three-stage charge process for fast recovery and conditioning, maximizing performance, and extending battery life. A selector switch adjusts output voltage to adapt to gel-cell, flooded lead-acid, or AGM battery types. An optional temperature compensation sensor also adjusts output for ideal voltage based on changes in the batteries’ ambient temperature. This model is housed in a rugged stainless-steel case with a durable white powder coat finish, and the internal circuitry is polyurethane-coated for maximum corrosion resistance. Features: “Smart” circuitry provides three-stage charging – bulk, absorption, float Gel-Cell/Flooded Lead-acid/AGM battery type switch selects optimum charge/float voltages Multiple isolated output banks; ammeter indicates total output current. (Except PT-7) The optional sensor adjusts output voltage based on battery temperature. (Except PT-7) Current limiting prevents damage from overloading Clean well-regulated output can be used as a power supply; can power loads directly without a battery in line Built to last – rugged stainless-steel case with a durable white powder coat finish with an optional drip shield and marinized internal circuitry Protection: Current Limiting, Thermal Protection, Forced Air Cooling, Drip Shield ABS-type approval for battery charging and power supplies Specifications: Input VAC (50-60 Hz.): 88-132 or 176-264  Input Amps @ Full Load: @ 115 VAC 2, @ 230 VAC 1     P.F. Rating: >.65  Max Output Amps: 7 Output Banks: 2  Battery Capacity (Amp-Hours): 14-70 Operating Temp. Rating Reference: T-1 Case Size Reference: A-1 Case Size (H x W x D): 10.5 x 5.0 x 2.8 inches (26.7 x 12.7 x 7.1 centimeters) Weight Lbs./Kg: 3.2/1.5 Optional Temp. Sensor Model: N/A Remote Panel Model: N/A  Equalize Option: No Output Indicator Reference: M-1 Compliance Reference: CG, CE     Temperature Rating References: Temperature: -10 degrees C to +45 degrees C     Derate Linearly From 100% @ 0 degrees C to 80% @ -10 degrees C Nominal Output Voltages at Gel/Flooded Switch Settings (without Temperature Compensation): Gel-Cell: 14.0 VDC Charge @ 50% load and 13.6 VDC Float @ .5 amp load Flooded/AGM: 14.2 VDC Charge @ 50% load and 13.4 VDC Float @ .5 amp load Compliance References: CG: USCG CFR 183.410 (Ignition protected) CE: Carries the CE mark ABS: PT Series meet SVR 2009 4-8-3/5.9, Under 90 meters Rules 2006 4-6-4/7.19, and HSNC 2007 4-8-3/5.13 This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Attention Sailers!!! Do you have a Binnacle mounted compass that is looking really bad? Now is the time to update to a New Ritchie DNP-200 Navigator Compass. We have one in stock in our clearance section selling for have the price. Ritchie Navigator Compass Navigator Compass Features: 4-1/2" PowerDamp Flat Card Dial with Large Numerals Brushed Stainless Housing Ideal for both Power and Sail Boats Fits all Popular Sailboat Steering Pedestals Exclusive Built-in Green NiteVu Night Illumination Built-in Compensators to Easily Adjust for Deviation Scientifically Matched Sapphire Jewel and Hardened Steel Pivot Dial Movement Internal Gimbal Systems for Maximum Stability During Adverse Pitch and Roll Conditions Powerful DirectiveForce Magnets for Fast Heading Lock-on Movable Sun Shield 45 Degree Lubber Lines High Temperature Construction for Extended Operating Range Custom Fitted Protective Covers Available (weather shield model no. WS-P) Easily Installed, Fits 5.25" (13.35 cm) Mounting Hole 100% Repairable Exclusive 5-Year Ritchie Warranty   Get it today before it's gone at  https://www.clrmarine.com/m4/10377--ritchie-dnp-200-navigator-compass-binnacle-mount.html

PT-14W Battery Charger Newmar’s Phase Three Series Battery Chargers employ “Smart” battery charging technology for 12-volt systems aboard marine applications including workboats, military vessels, commercial vessels, and recreational craft. This charger interacts with batteries, providing the optimum three-stage charge process for fast recovery and conditioning, maximizing performance, and extending battery life. A selector switch adjusts output voltage to adapt to gel-cell, flooded lead-acid, or AGM battery types. An optional temperature compensation sensor also adjusts output for ideal voltage based on changes in the batteries’ ambient temperature. This model is housed in a rugged stainless-steel case with a durable white powder coat finish, and the internal circuitry is polyurethane-coated for maximum corrosion resistance. Features: “Smart” circuitry provides three-stage charging – bulk, absorption, float Gel-Cell/Flooded Lead-acid/AGM battery type switch selects optimum charge/float voltages Multiple isolated output banks; ammeter indicates total output current. (Except PT-7) The optional sensor adjusts output voltage based on battery temperature. (Except PT-7) Current limiting prevents damage from overloading Clean well-regulated output can be used as a power supply; can power loads directly without a battery in line Built to last – rugged stainless-steel case with a durable white powder coat finish with an optional drip shield and marinized internal circuitry Protection: Current Limiting, Thermal Protection, Forced Air Cooling, Drip Shield ABS-type approval for battery charging and power supplies Specifications: Input VAC (50-60 Hz.): 85-264     Input Amps @ Full Load: @ 115 VAC: 2.8, @ 230 VAC: 1.4  P.F. Rating: .93@230V and .98@115V Max Output Amps: 14 Output Banks: 3 Battery Capacity (Amp-Hours): 28-140     Operating Temp. Rating Reference: T-2 Case Size Reference: A-2 Case Size (H x W x D): 11.2A x 7.7 x 4.75A inches (31.8A x 19.6 x 12.1A centimeters) *Note with Dripshield installed A add 1.1” (2.8 cm) to height and .92” (2.3 cm) to depth Weight Lbs./Kg: 8/4 Optional Temp. Sensor Model: TCS-12/24     Remote Panel Model: RP Equalize Option: Yes Output Indicator Reference: M-3 Compliance Reference: CG, CE     Temperature Rating References: Temperature: -10 degrees C to +60 degrees C     Derate Linearly From 100% @ 40 degrees C to 60% @ 60 degrees C Nominal Output Voltages at Gel/Flooded Switch Settings (without Temperature Compensation): Gel-Cell: 14.0 VDC Charge @ 50% load and 13.6 VDC Float @ .5 amp load Flooded/AGM: 14.2 VDC Charge @ 50% load and 13.4 VDC Float @ .5 amp load Compliance References: CG: USCG CFR 183.410 (Ignition protected) CE: Carries the CE mark ABS: PT Series meets SVR 2009 4-8-3/5.9, Under 90 meters Rules 2006 4-6-4/7.19, and HSNC 2007 4-8-3/5.13. Options: Remote Panel, model RP, for use with all models except PT-7 and PT-40U (LEDs indicate the charger output stage. Manual re-initialization of a three-stage charge cycle. With 25′ of cable. Panel dimensions: 3″ H x 4.75″ W) This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

PT-25W Battery Charger Newmar’s Phase Three Series Battery Chargers employ “Smart” battery charging technology for 12-volt systems aboard marine applications including workboats, military vessels, commercial vessels, and recreational craft. This charger interacts with batteries, providing the optimum three-stage charge process for fast recovery and conditioning, maximizing performance, and extending battery life. A selector switch adjusts output voltage to adapt to gel-cell, flooded lead-acid, or AGM battery types. An optional temperature compensation sensor also adjusts output for ideal voltage based on changes in the batteries’ ambient temperature. This model is housed in a rugged stainless steel case with a durable white powder coat finish, and the internal circuitry is polyurethane coated for maximum corrosion resistance. Features: 12-volt model “Smart” circuitry provides three-stage charging – bulk, absorption, and float Gel-Cell/Flooded Lead-acid/AGM battery type switch selects optimum charge/float voltages Multiple isolated output banks; ammeter indicates total output current. (Except PT-7) The optional sensor adjusts the output voltage based on battery temperature. (Except PT-7) Current limitations prevent damage from overloading Clean well-regulated output can be used as a power supply; can power loads directly without a battery in line Built to last – rugged stainless steel case with a durable white powder coat finish, an optional drip shield, and marinized internal circuitry Protection: Current Limiting, Thermal Protection, Forced Air Cooling, Drip Shield ABS-type approval for battery charging and power supplies Specifications: Input VAC (50-60 Hz.): 90-132 or 180-264 Input Amps @ Full Load: @ 115 VAC: 6.5, @ 230 VAC: 4 Power Factor: .7 Max Output Amps: 25 Output Banks: 3 Battery Capacity (Amp-Hours): 50-250 Operating Temp. Rating Reference: T-4 Case Size Reference: A-2 Case Size (H x W x D): 11.2A x 7.7 x 4.75A inches (31.8A x 19.6 x 12.1A centimeters) *Note with Dripshield installed A add 1.1” (2.8 cm) to height and .92” (2.3 cm) to depth Weight Lbs./Kg: 8.2/4 Optional Temp. Sensor Model: TCS-12/24                 Remote Panel Model: RP Equalize Option: Yes Output Indicator Reference: M-3 Compliance Reference: CG Temperature Rating References: Temperature: -20 degrees C to +60 degrees C Derate Linearly From 100% @ 50 degrees C to 60% @ 60 degrees C Nominal Output Voltages at Gel/Flooded Switch Settings (without Temperature Compensation): Gel-Cell: 14.0 VDC Charge @ 50% load and 13.6 VDC Float @ .5 amp load Flooded/AGM: 14.2 VDC Charge @ 50% load and 13.4 VDC Float @ .5 amp load Compliance References: CG: USCG CFR 183.410 (Ignition protected) CE: Carries the CE mark ABS: PT Series meets SVR 2009 4-8-3/5.9, Under 90 meters Rules 2006 4-6-4/7.19, and HSNC 2007 4-8-3/5.13. Options: Remote Panel, model RP, for use with all models except PT-7 and PT-40U (LEDs indicate charger output stage. Manual re-initialization of three-stage charge cycle. With 25′ of cable. Panel dimensions: 3″ H x 4.75″ W) Temperature Compensation Sensor, Model TCS 12/24, for use with all models except PT 7 (-5 mV per cell degrees C, 25′ cable (40’cable optional) This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

PT-40U Battery Charger Newmar’s Phase Three Series Battery Chargers employ “Smart” battery charging technology for 12-volt systems aboard marine applications including workboats, military vessels, commercial vessels, and recreational craft. This charger interacts with batteries, providing the optimum three-stage charge process for fast recovery and conditioning, maximizing performance, and extending battery life. A selector switch adjusts output voltage to adapt to gel-cell, flooded lead-acid, or AGM battery types. An optional temperature compensation sensor also adjusts output for ideal voltage based on changes in the batteries’ ambient temperature. This model is housed in a rugged stainless steel case with a durable white powder coat finish, and the internal circuitry is polyurethane coated for maximum corrosion resistance. Features: 12-volt model “Smart” circuitry provides three-stage charging – bulk, absorption, and float Gel-Cell/Flooded Lead-acid/AGM battery type switch selects optimum charge/float voltages Multiple isolated output banks; ammeter indicates total output current. (Except PT-7) The optional sensor adjusts the output voltage based on battery temperature. (Except PT-7) Current limitations prevent damage from overloading Clean well-regulated output can be used as a power supply; can power loads directly without a battery in line Built to last – rugged stainless steel case with a durable white powder coat finish, an optional drip shield, and marinized internal circuitry Protection: Current Limiting, Thermal Protection, Forced Air Cooling, Drip Shield ABS-type approval for battery charging and power supplies Specifications: Input VAC (50-60 Hz.): 90-264 Input Amps @ Full Load: @ 115 VAC: 6.8, @ 230 VAC: 3.4 Power Factor: .98 @ 115V and .95 @ 230V Max Output Amps: 40 Output Banks: 3 Battery Capacity (Amp-Hours): 80-400     Operating Temp. Rating Reference: T-5 Case Size Reference: A-3 Case Size (H x W x D): 13.85B x 9.5 x 4.8B inches (35.2B x 24.1 x 12.2B centimeters) *Note with Dripshield installed B add .75” (1.9 cm) to height and 1.35” (3.4 cm) to depth Weight Lbs./Kg: 11/6 Optional Temp. Sensor Model: TCS-12/24                 Remote Panel Model: EVM-12-2     Equalize Option: No Output Indicator Reference: M-3 Compliance Reference: CG Temperature Rating References: Temperature: -20 degrees C to +70 degrees C Derate Linearly From 100% @ 50 degrees C to 50% @ 70 degrees C Nominal Output Voltages at Gel/Flooded Switch Settings (without Temperature Compensation): Gel-Cell: 14.0 VDC Charge @ 50% load and 13.6 VDC Float @ .5 amp load Flooded/AGM: 14.2 VDC Charge @ 50% load and 13.4 VDC Float @ .5 amp load Compliance References: CG: USCG CFR 183.410 (Ignition protected) CE: Carries the CE mark ABS: PT Series meets SVR 2009 4-8-3/5.9, Under 90 meters Rules 2006 4-6-4/7.19, and HSNC 2007 4-8-3/5.13. Options: Remote Panel, model EVM-12-2, for us with model PT-40 only (Enables monitoring of when the battery charger is “on” and the batteries’ state of readiness, at a glance of two (2) battery banks only) Temperature Compensation Sensor, Model TCS 12/24, for use with all models except PT 7 (-5 mV per cell degrees C, 25′ cable (40’cable optional) This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

PT-80 Battery Charger Newmar’s Phase Three Series Battery Chargers employ “Smart” battery charging technology for 12-volt systems aboard marine applications including workboats, military vessels, commercial vessels, and recreational craft. This charger interacts with batteries, providing the optimum three-stage charge process for fast recovery and conditioning, maximizing performance, and extending battery life. A selector switch adjusts output voltage to adapt to gel-cell, flooded lead-acid, or AGM battery types. An optional temperature compensation sensor also adjusts output for ideal voltage based on changes in the batteries’ ambient temperature. This model is housed in a rugged stainless steel case with a durable white powder coat finish, and the internal circuitry is polyurethane coated for maximum corrosion resistance. Features: 12-volt model “Smart” circuitry provides three-stage charging – bulk, absorption, and float Gel-Cell/Flooded Lead-acid/AGM battery type switch selects optimum charge/float voltages Multiple isolated output banks; ammeter indicates total output current. (Except PT-7) The optional sensor adjusts the output voltage based on battery temperature. (Except PT-7) Current limitations prevent damage from overloading Clean well-regulated output can be used as a power supply; can power loads directly without a battery in line Built to last – rugged stainless steel case with a durable white powder coat finish, an optional drip shield, and marinized internal circuitry Protection: Current Limiting, Thermal Protection, Forced Air Cooling, Drip Shield ABS-type approval for battery charging and power supplies Specifications: Input VAC (50-60 Hz.): 90-264 Input Amps @ Full Load: @ 115 VAC: 12, @ 230 VAC: 7 Power Factor: .95@230V or .98@115V Max Output Amps: 80 Output Banks: 3 Battery Capacity (Amp-Hours): 160-800 Operating Temp. Rating Reference: T-7 Case Size Reference: A-5 Case Size (H x W x D): 16.8C x 9.6 x 6.1C inches (42.7C x 24.4 x 15.5C centimeters) *Note with Dripshield installed C add 1” (2.54 cm) to height and .5” (1.27 cm) to depth Weight Lbs./Kg: 15.2/7 Optional Temp. Sensor Model: TCS-12/24                 Remote Panel Model: RP Equalize Option: Yes Output Indicator Reference: M-3 Compliance Reference: CE Temperature Rating References: Temperature: -10 degrees C to +60 degrees C Derate Linearly From 100% @ 50 degrees C to 80% @ 60 degrees C Nominal Output Voltages at Gel/Flooded Switch Settings (without Temperature Compensation): Gel-Cell: 14.0 VDC Charge @ 50% load and 13.6 VDC Float @ .5 amp load Flooded/AGM: 14.2 VDC Charge @ 50% load and 13.4 VDC Float @ .5 amp load Compliance References: CG: USCG CFR 183.410 (Ignition protected) CE: Carries the CE mark ABS: PT Series meet SVR 2009 4-8-3/5.9, Under 90 meters Rules 2006 4-6-4/7.19, and HSNC 2007 4-8-3/5.13 Options: Remote Panel, model RP, for use with all models except PT-7 and PT-40U (LEDs indicate charger output stage. Manual re-initialization of three-stage charge cycle. With 25′ of cable. Panel dimensions: 3″ H x 4.75″ W) Temperature Compensation Sensor, Model TCS 12/24, for use with all models except PT 7 (-5 mV per cell degrees C, 25′ cable (40’cable optional) This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Waterproof Battery Guard - 200 Amps The complete universal programmable Battery Guard (BGW) prevents the excessive discharge of the battery (which would damage the battery) and protects electronic appliances against overvoltage. The BGW 200 battery guard has "Automatic Board System Detection"; the BGW automatically detects the battery voltage (12 or 24 V). The BGW 200 battery guard can carry a 200 A continuous load and a 1000 A peak current at 25 degrees. You can choose between 10 on/off threshold voltage programs for both 12V and 24V battery systems, which can be easily programmed. Features: Can be set to connect/disconnect at several different voltages Batteries last longer Prevents damage to connected components Protects against excessive voltage caused by faulty alternators or chargers E-mark, pending 2-year warranty Specifications: Input Voltage: Automatic detection 12/24 V Output Voltage: 9,5-27,6 VDC Dimensions: 39 x 76 x 111 mm Output: 200 Amps Weight: 0,295 Kg *No battery included

Engine Cooling Recirculating Pump    More Info: Small Block Chrysler 273 318 340 360 3004886 3745985, Volvo AQ200-311 835390-6 856364-5 PUMP TYPE Chrysler Block Recirculating Pumps   APPLICATIONS / CHARACTERISTICS New bi-rotational recirculating pumps manufactured with brass impellers, plugs and fittings, premium coated castings, upgraded marine mechanical seal and all required mounting gaskets.

Shurflo 902-200 DC Controller For 9300 The 902-200 has all the features of the Shurflo's 902-100 pump controller and more. It optimizes your solar water pumping system by translating the current and voltage from your PV panels into a combination that is better matched to the pump's needs. This allows your SHURflo 9300-series pump to start pumping earlier in the morning and run later into the evening.   SHURflo 902-200 Pump Controller Features Increases daily water output by up to 30% Protects pump from low or high voltage conditions Switch-selectable for 12 VDC or 24 VDC operation Pump on/off switch Water-tight enclosure and cable inlets Terminals for float switch Includes water level monitor mode with probes and cable

Groco B-200 Motor Base Stamping, Blk  

Groco B-200-G Pump Base Grommets (4Pk)  

Jabsco 9970-200 Pump for Perkins 4-107 Pump Body: Bronze Flange Mounted Port Size: 3/4" BSP Thread (not NPT) Impeller: Neoprene Shaft Seal: Mechanical Shaft: Stainless Steel   Flange Mounted Engine Cooling Pump   The 9970-200 model uses a short shaft with a coupling.  

Globe Impeller 200 Globe Impeller Model 200 Replaces the following impellers Ancor JP50015 CEF 500245 Detroit Diesel 5198550 Jabsco 18376-0001, 6760-0001 Johnson Pump 09-802B, 802B Sierra Marine 18-3304 Volvo Penta 842857, 844683, 845796 Weight: 0.6 lbs. Od (in/mm): 3 3/4" / 95 Width (in/mm): 3 1/2" / 90 Shaft Size (in/mm): 1" / 25 Drive Type: 12 pt Spline Core Type: Composite Number of Blades: 9 Silhouette Letter: O Fuel Type: Water