12-12-6i Power Stabilizer Feed sensitive electronics with proper voltage, regardless of the battery condition. This stabilizing converter provides continuous, precisely regulated output over the entire range of a battery’s usable voltage. This prevents subjecting loads to fluctuating input voltage, which can cause shutdown, diminish performance, and possibly damage sensitive circuitry. This converter provides total input/output isolation, virtually eliminating conducted line noise and permitting the connection of negative ground gear to positive or floating ground systems, or vice versa. It can be modified for use as a battery charger, allowing them to maintain a battery at a great distance from the primary voltage source, providing reserve power if the main source fails. The rugged anodized aluminum case is ideal for marine applications. Application Benefits Include: Operate electronics at optimal input voltage, even from nearly drained batteries Boost voltage to compensate for voltage drops in long wire runs from batteries Eliminate voltage drops during momentary high current drain from batteries, as during engine start Eliminate voltage fluctuation from charge sources Eliminate voltage overshoot due to sudden removal of high current load Specifications: Input Voltage: 10-16 Input Amps: 8 Output Voltage: 13.6 Output Amps (Intermittent): 6 Output Amps (Continuous): 6 Case Size (H x W x D): 6.5 x 4.0 x 1.75 inches (6.8 x 10.2 x 4.5 centimeters) Weight: 2 lb. (.9 kg) Output: 12 or 24V, nominal, see matrix Ripple: 150 mV P-P maximum Regulation: 1% Line/Load Duty Cycle Ratings: Intermittent: 20 minutes max on time, 20% duty. The current limit is set at approx. 105% of intermittent rating. Continuous: 24 hours, 100% duty Idle Current: Less than 100 mA (including power “ON” light ) Operating Temp: 0-50 degrees C, Derate Linearly From 100% @ 40 degrees C To 50% @ 50 degrees C. Thermal shutdown @ 70 degrees C Case Temperature. Switching Frequency: 40 kHz. Efficiency: 85% – Typical. Isolation – Output/Chassis; Input/chassis: 250 VDC Mechanical Specifications: Anodized aluminum heat sink case Front panel terminal block Heavy-duty mounting flange Conformal-coated PC board Options/Factory Modifications: Operation as a battery charger (contact factory) Parallel/redundant operation (contact factory) High-vibration mounting kit Non-standard output voltage (contact factory) Option: Extreme Vibration Mounting Kit The Extreme Vibration Mounting Kit is available to protect NEWMAR power converters from the extreme stresses of shock and vibration when mounted on high-vibration vehicles. The kit (pictured here) replaces the standard vibration kit provided with the unit and fits into the unit’s mounting flange to act as a “super shock absorber” for electronics in high-vibration applications. It is available to fit all NEWMAR units from 2 to 70 lbs. Specify KIT–L for units that weigh 2–15 lbs. and Kit–H for units that weigh 16-70 lbs. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

12-12-3i Power Stabilizer Feed sensitive electronics with proper voltage, regardless of the battery condition. This stabilizing converter provides continuous, precisely regulated output over the entire range of a battery’s usable voltage. This prevents subjecting loads to fluctuating input voltage, which can cause shutdown, diminish performance, and possibly damage sensitive circuitry. This converter provides total input/output isolation, virtually eliminating conducted line noise and permitting the connection of negative ground gear to positive or floating ground systems, or vice versa. It can be modified for use as a battery charger, allowing them to maintain a battery at a great distance from the primary voltage source, providing reserve power if the main source fails. The rugged anodized aluminum case is ideal for marine applications. Application Benefits Include: Operate electronics at optimal input voltage, even from nearly drained batteries Boost voltage to compensate for voltage drops in long wire runs from batteries Eliminate voltage drops during momentary high current drain from batteries, as during engine start Eliminate voltage fluctuation from charge sources Eliminate voltage overshoot due to sudden removal of high current load Specifications: Input Voltage: 10-16 Input Amps: 4 Output Voltage: 13.6 Output Amps (Intermittent): 3 Output Amps (Continuous): 3 Case Size (H x W x D): 3.5 x 3.5 x 1.75 inches (8.9 x 8.9 x 4.5 centimeters) Weight: 1 lb. (.45 kg) Output: 12 or 24V, nominal, see matrix Ripple: 150 mV P-P maximum Regulation: 1% Line/Load Duty Cycle Ratings: Intermittent: 20 minutes max on time, 20% duty. Current limit is set at approx. 105% of intermittent rating. Continuous: 24 hours, 100% duty Idle Current: Less than 100 mA (including power “ON” light ) Operating Temp: 0-50 degrees C, Derate Linearly From 100% @ 40 degrees C To 50% @ 50 degrees C. Thermal shutdown @ 70 degrees C Case Temperature. Switching Frequency: 40 kHz. Efficiency: 85% – Typical. Isolation – Output/Chassis; Input/chassis: 250 VDC Mechanical Specifications: Anodized aluminum heat sink case Front panel terminal block Heavy-duty mounting flange Conformal-coated PC board Options/Factory Modifications: Operation as a battery charger (contact factory) Parallel/redundant operation (contact factory) High-vibration mounting kit Non-standard output voltage (contact factory) Option: Extreme Vibration Mounting Kit The Extreme Vibration Mounting Kit is available to protect NEWMAR power converters from the extreme stresses of shock and vibration when mounted on high-vibration vehicles. The kit (pictured here) replaces the standard vibration kit provided with the unit and fits into the unit’s mounting flange to act as a “super shock absorber” for electronics in high-vibration applications. It is available to fit all NEWMAR units from 2 to 70 lbs. Specify KIT–L for units that weigh 2–15 lbs. and Kit–H for units that weigh 16-70 lbs. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

115-12-20A Power Supply This super-rugged DC power supply is ideal for powering 12-volt communication and navigation equipment onboard commercial vessels where reliability is essential. The proven linear circuit design provides pure noise-free output and a long service life. Features: Excellent Regulation and Ripple Spec (output voltage maintained within 1% under all rated line and load conditions) Polyurethane conformal coated PC board and corrosion-resistant heavy-duty aluminum case with integral shock mounts assure survival in hostile environments The heat generated by semi-conductors is extracted and dissipated by large heat sink fins for cool operation Protection: overvoltage, current limit; (set @ 105% of intermittent rating), thermal overload, and input/output fusing Thermally activated cooling fan on “CD” units Specifications: Nominal Input/VAC: 115/230     Maximum Input Current @115: 5.5 Maximum Input Current @230: 2.5 Output Amperage (Intermittent): 20 Output Amperage (Continuous): 8 Weight: 20 lbs. / 9.1 kg Case Size: H x W x D (inch): 5.7” x 4.8” x 16.3” Input Range 105-125/210-250 VAC (selectable), 50-60 Hz; Derate to 50% output below 110 and 220 VAC Operating Temperature Standard Units - 0-50 degrees C, Derate linearly from 100% @ 40 degrees C to 50% @ 50 degrees C thermal shutdown @ 85 degrees C case temperature Duty Cycle: Intermittent: 20 minutes max on time, 20% duty Continuous: 24 hours/day 100% Duty Options: Modify for use as a battery charger The output voltage is adjusted (see Output Voltage for range) Transfer relay for back-up battery in event of power failure (ERC option) Output Voltage: 13.6 VDC (internally adjustable 12.6-14.5 VDC) Ripple: 40mV P-P (@ 110-125 / 220-250 VAC input) 1% Line and Load (@ 110-125 / 220-250 VAC input) Mechanical: Powder-coated aluminum heat sink case Front panel terminal block Heavy-duty mounting flange Conformal-coated PC board This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

115-12-35CD Power Supply This super-rugged DC power supply is ideal for powering 12-volt communication and navigation equipment onboard commercial vessels where reliability is essential. The proven linear circuit design provides pure noise-free output and a long service life. Features: Excellent Regulation and Ripple Spec (output voltage maintained within 1% under all rated line and load conditions) Polyurethane conformal coated PC board and corrosion-resistant heavy-duty aluminum case with integral shock mounts assure survival in hostile environments The heat generated by semi-conductors is extracted and dissipated by large heat sink fins for cool operation Protection: overvoltage, current limit; (set @ 105% of intermittent rating), thermal overload, and input/output fusing Thermally activated cooling fan on “CD” units Specifications: Nominal Input/VAC: 115/230     Maximum Input Current @115: 7.5 Maximum Input Current @230: 3.5 Output Amperage (Intermittent): 35 Output Amperage (Continuous): 35 Weight: 32 lbs. / 14.6 kg Case Size: H x W x D (inch): 6.5” x 9.5” x 14.0” Input Range 105-125/210-250 VAC (selectable), 50-60 Hz; Derate to 50% output below 110 and 220 VAC Operating Temperature C.D. Units - 0-65 degrees C, Derate linearly from 100% @ 50 degrees C to 50% @ 65 degrees C thermal Shutdown @ 85 degrees C case temperature Duty Cycle: Intermittent: 20 minutes max on time, 20% duty Continuous: 24 hours/day 100% Duty Options: Modify for use as a battery charger The output voltage is adjusted (see Output Voltage for range) Transfer relay for back-up battery in event of power failure (ERC option) Output Voltage: 13.6 VDC (internally adjustable 12.6-14.5 VDC) Ripple: 40mV P-P (@ 110-125 / 220-250 VAC input) 1% Line and Load (@ 110-125 / 220-250 VAC input) Mechanical: Powder-coated aluminum heat sink case Front panel terminal block Heavy-duty mounting flange Conformal-coated PC board This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

115-12-8 Power Supply This super-rugged DC power supply is ideal for powering 12-volt communication and navigation equipment onboard commercial vessels where reliability is essential. The proven linear circuit design provides pure noise-free output and a long service life. Features: Excellent Regulation and Ripple Spec (output voltage maintained within 1% under all rated line and load conditions) Polyurethane conformal coated PC board and corrosion-resistant heavy-duty aluminum case with integral shock mounts assure survival in hostile environments The heat generated by semi-conductors is extracted and dissipated by large heat sink fins for cool operation Protection: overvoltage, current limit; (set @ 105% of intermittent rating), thermal overload, and input/output fusing Thermally activated cooling fan on “CD” units Specifications: Nominal Input/VAC: 115/230     Maximum Input Current @115: 2.5 Maximum Input Current @230: 1.5 Output Amperage (Intermittent): 8 Output Amperage (Continuous): 5 Weight: 32 lbs. / 14.6 kg Case Size: H x W x D (inch): 6.0” x 4.6” x 8.5” Input Range 105-125/210-250 VAC (selectable), 50-60 Hz; Derate to 50% output below 110 and 220 VAC Operating Temperature Standard Units - 0-50 degrees C, Derate linearly from 100% @ 40 degrees C to 50% @ 50 degrees C thermal shutdown @ 85 degrees C case temperature Duty Cycle: Intermittent: 20 minutes max on time, 20% duty Continuous: 24 hours/day 100% Duty Options: Modify for use as a battery charger The output voltage is adjusted (see Output Voltage for range) Transfer relay for back-up battery in event of power failure (ERC option) Output Voltage: 13.6 VDC (internally adjustable 12.6-14.5 VDC) Ripple: 40mV P-P (@ 110-125 / 220-250 VAC input) 1% Line and Load (@ 110-125 / 220-250 VAC input) Mechanical: Powder-coated aluminum heat sink case Front panel terminal block Heavy-duty mounting flange Conformal-coated PC board This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

3-Pin, 12/24V Power Cable - 1.5M f/DSM30/300, CP300, 370, 450, 470 & 570 Features: Length: 1.5M 12/24V 3-Pin Compatible Devices: DSM30 DSM300 CP300 CP370 CP450 CP470 CP570 CP200 E120

12-12-35I DC Converter This isolated series provides voltage conversion as well as input/output isolation, allowing the use of negative ground gear in positive or floating ground battery systems, or vice versa.  Using an isolated converter as a voltage stabilizer on 12- or 24-volt systems can solve conducted noise and interference problems on sensitive DC-powered communication, navigation systems, and DC microprocessor-based devices. Features: Wide range of input voltage Precise output voltage regulation Reverse polarity Input fuse/output fuse Total input/output isolation, pos. or neg. ground Current-limiting, short-circuit-proof output Automatic resetting of the thermal shutdown High/low input voltage shutdown Polyurethane conformal coating on PC board Power ON light Rugged case designed for high-vibration applications Specifications: Input Voltage: 10-16 Max Input Amps: 56 Output Voltage: 13.6 Output Amps (Intermittent): 35 Output Amps (Continuous): 20 Case Size (H x W x D): 6 x 6.8 x 16.5 inches (15.2 x 17.3 x 41.9 centimeters) Weight: 12 lb. (5.5 kg) Output: 13.6 VDC (internally adjustable 12.6 -14.5) or 24.5 VDC (or specify) Ripple: 150 mV P-P maximum Regulation: 1% Line/Load Duty Cycle Ratings: Intermittent – 20 minutes max on time, 20% duty. current limit set at approx. 105% of the intermittent rating. Continuous – 24 hours, 100% duty Idle Current: Less than 100 mA (including power “ON” light ) Operating Temp: 0-50 degrees C, Derate Linearly From 100% @ 40 degrees C To 50% @ 50 degrees C. Thermal shutdown @ 70 degrees C Case Temperature Switching Frequency: 40 kHz Efficiency: 85% – Typical Isolation – Output/Chassis; Input/chassis: 250 VDC Mechanical Specifications: Anodized aluminum heat sink case Front panel terminal block Heavy-duty mounting flange conformal-coated PC board Options: Operation as battery charger or parallel redundant operation* – derate to continuous duty rating (contact factory) Extreme vibration mounting kit. (Information below) Option: Extreme Vibration Mounting Kit The Extreme Vibration Mounting Kit is available to protect NEWMAR power converters from the extreme stresses of shock and vibration when mounted on high-vibration vehicles. The kit replaces the standard vibration kit provided with the unit and fits into the unit’s mounting flange to act as a ‘super shock absorber’ for electronics in high-vibration applications. It is available to fit all NEWMAR units from 2 to 70 lbs. Specify Kit L for units that weigh 2 -15 lbs. and Kit H for units that weigh 16 – 70 lbs. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

PowerPod Pre-Cut for Furuno NavNet TZTouch3 12″ (TZT12F) PowerPods are better than bracket mounting. Sturdy and secure, yet clean and attractive, PowerPods position your fishfinder/chartplotter at a 20-degree viewing angle. PowerPods provide the clean look of flush mounting with the advantages of a swivel base. PowerPods are now available in two color options. All models are available in high gloss white, and many models (PP4400-C, PP4500-C, PP4600-C, PP4800-C, PP4900-C, PP5050-C, PP5100-C, PP5200-C, PP5920-C Series) are also available in black carbon print. Constructed out of durable ABS like all Gen3 NavPods, these new black carbon models have the same high gloss finish with UV stability. NavPods are made to protect your marine electronics from the harshest of wet boating conditions. All NavPods are manufactured with a double gasket system that provides an excellent watertight seal. PowerPods keep the spray off the electrical connections on the back of your fishfinder/chartplotter, assuring reliability and longevity of your marine electronics. Your fishfinder/chartplotter is easily flush mounted into the pre-cut face of the PowerPod. The base has a large opening (1.1″ for PP4100, PP4400, PP4500, PP4600 Series; 1.8″ for PP4800, PP4900, PP5030, PP5050, PP5060, PP5100, PP5200, PP5920 models) to provide plenty of room for running wires and connectors through the base to conceal them from the elements. This provides protection for wires and connectors from water intrusion, UV exposure, or damage from getting snagged and ripped out of their sockets. All NavPods come with a security wrench and Nickel Chrome-Plated Stainless Steel tamper-resistant screws for a little bling and a lot of security. PowerPod pre-cut models are available for most 7″, 9″, 12″ and 16″ displays from all major marine electronic manufacturers. NavPod backs up its commitment to quality by offering a 10-year warranty on all Gen3 NavPods. PowerPods: Protection, Convenience, Security.

12V-24V 7 Amp Converter for DRS12AX X-Class Open Array - Newmar Newmar 12-24-7 Step Up Dc-Dc Converter 7amp Conitnuos These "UP" converters produce 24 volts from 12 volt systems and are ideal for managing dual voltage applications on marine vessels without having to install a 24 volt battery and dedicated charging system. Choose from two types depending on your application: In the Standard, Non-Isolated Series the 12V input and 24V output share a common negative ground and are ideal when installing certain electronics that operate better on 24 volts when a robust 12 volt system exists. Models available in outputs of 7, 16 and 25 amps. Standard, Non-Isolated Series Intended for use on negative ground systems 10 -15 VDC input range 7 Amp output Current limited, voltage spike suppression, automatic thermal shutdown and recovery Specifications: Input: 10 - 15V DC Output: 27.2 VDC +/-5% at extreme temperature load, input, tolerance, etc. Ripple: <100mV P-P Regulation: +/- 5% Line/Load Duty Cycle: Intermittent: 2 minutes, 20% duty Continuous: 24 hours, 100% duty Operating Temp: -25º - 30º C, derate linearly from 30 to 0% @ 80º C Mechanical Efficiency: 93% - Typical. Anodized aluminum, glass filled polycarbonate, dust water and impact resistance to IP533 Front panel terminal block Output indicator: Green LED WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

PP5030-01 PowerPod Pre-Cut for Humminbird ION 12.1" PowerPods are designed for the serious boater who is blasting offshore. He demands the most from his boat and his electronics. He needs a tough and rugged mount to protect vital electronics from the harshest of offshore boating conditions. Sturdy and secure, yet clean and attractive, PowerPods are better than bracket mounting. Over 70 Pre-Cut PowerPods are available for all popular manufacturers products. 1.8" opening in the swivel tube provides plenty of room for running wires and connectors through. PowerPods are positioned at a 20 degree tilt back viewing angle. PowerPods for Sail are for mounting on a flat surface. Perhaps under the dodger or aft end of the cockpit table especially on boats with dual wheels. The Hi-Gloss Material NavPods are manufactured with a custom co-extruded acrylic capped ABS material. We use the absolute best UV resistant material that provides a very high gloss white finish that matches gel-coated fiberglass. The Gen3 enhancements now include a thicker gauge material that improves strength and provides for better structural rigidity. The Waterproof Seal All NavPods are manufactured with a double gasket system providing an excellent watertight seal between the front and back of the NavPod for protection of your Marine Electronics. NavPods are made to withstand the harshest of wet offshore boating conditions. Gen3 enhancements include a thicker external silicone gasket with improved flush fit. The internal EPDM gasket is now 50% thicker and is not subject to "compression set" like many rubber compounds. This is important when you need to open the NavPod in the future to service your electronics. The Nickel Chrome Plated Screws We use all stainless steel mounting hardware that is supplied with each NavPod. Large round head tamperproof screws have deeper sockets for the NavPod wrench for better holding ability when tightening than the previous screws. For Gen3 we provide nickel chrome-plated stainless steel tamperproof screws for security combined with a little bling! The Manufacturing Process Heavy-gauge thermoforming is considered an art since many processes come into play. It all starts with the design and development of the tooling. We are fortunate to have experienced in-house design engineers who utilize CAD programs like Solidworks, Catia and AutoCad. Surfcam is used to interface with our CNC machining centers to produce quality tools with precision tolerances. Our Commitment to Quality We are committed to producing the best possible waterproof housing for Marine Electronics. Now with two decades of experience under our belt, we are confident you will have years of trouble free service and a long lasting high gloss finish. We will stand behind our commitment by now offering a 10-year warranty on all new Gen3 NavPods.

PC-10 Power Conditioner Noise Filter The interference or electronic “noise” generated by alternators, ignition systems, motors, etc. can render a vehicle or vessel’s radio or other electronic equipment virtually useless. This interference takes the form of popping or static on radios or audio gear and garbled images or “hashes” on video displays. These specialized filters can be used singly or in combination to attenuate conducted line noise, either at the affected equipment or at the noise source. Features: Heavy-duty aluminum construction Operate on 6-48 VDC systems Integral mounting flanges for secure installation Nickle-plated, brass stud connectors on alternator filters accommodate high-current cables and terminals Color-coded wire leads on PC models make in-line installation easy Specifications: Filtered Frequencies: Audio – 200 MHz Rating: 10 amp Installation Location: At affected equipment in “+” and “-” leads     Dimensions (inches): 1.25 x 4.25 x 3 Weight (lbs): 1

PC-25 Power Conditioner Noise Filter The interference or electronic “noise” generated by alternators, ignition systems, motors, etc. can render a vehicle or vessel’s radio or other electronic equipment virtually useless. This interference takes the form of popping or static on radios or audio gear and garbled images or “hashes” on video displays. These specialized filters can be used singly or in combination to attenuate conducted line noise, either at the affected equipment or at the noise source. Features: Heavy-duty aluminum construction Operate on 6-48 VDC systems Integral mounting flanges for secure installation Nickle-plated, brass stud connectors on alternator filters accommodate high-current cables and terminals Color-coded wire leads on PC models make in-line installation easy Specifications: Filtered Frequencies: Audio – 200 MHz Rating: 25 amp Installation Location: At affected equipment in “+” and “-” leads     Dimensions (inches): 2 x 4.25 x 3.25 Weight (lbs): 2

Vac N' Blo Hi Performance Hand Vac/Blower Pound for Pound, the Vac N Blo® is the most Powerful Hand Vac/Blower on the Planet! Catalog P/N VM12500 Features: 500 Watts of power with a new state of the art fan enclosed motor. The 500 series produces Sealed Suction Measurement of 60" water lift (A scientific method of measuring vacuum cleaner suction)  The vacuum is designed for DRY PICK UP ONLY All steel construction with black powder coat finish. Technical Specifications: Construction - All-steel baked enamel finish Vacuum Filter - Bag Hose Length - 1' Motor/Voltage - 120 VAC Power - 500 W Amps - 12 AMPS Airflow - 20 CFM/8,000 FPM Cord - 12' Plug - Two (2) prong electrical plug   Vacuum Capacity - 1/4 Gallon Vacuum Air Flow - 70 CFM Dimensions - 16.5" x 5.25" x 6"  Weight - 3 Pounds In the Box: Vacuum Extension wand Pik-All Nozzle Dust brush Crevice tool Inflator adapter  Shoulder strap Disposable paper bag x 6 *Sold as an Individual  WARNING: This product can expose you to chemicals including CARBON BLACK which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.

Yamada NDP-50BAN Pump (852229) Buna N 2" Ports NDP-50BAN AIR POWERED DOUBLE DIAPHRAGM PUMP   Yamada® NDP-50BAN series Air Powered Double Diaphragm (AODD) pumps provide a maximum flow rate of 166 gallons per minute.   Air Exhaust: 1" Female NPT (includes silencer) Air Inlet: 3/4" Female NPT (includes ball valve) Air Supply Pressure: 20 to 100 PSI (1.4 to 7 kgf/cm²) Diaphragm: Buna-N Discharge Volume Per Cycle: 1.14 gallons (4.3 liters) Fluid Port: 2" (NPT or ANSI Flange) Liquid Temperature: 180°F (82°C) Max Material: Aluminum - Combination fluid port: ANSI Flange with 2" tapped FNPT (ADC-12) Max Cycles Per Minute: 146 Maximum Flow (GPM): 164 Max Suction Lift: 19 feet Model Number: 852229 Model Series: NDP-50 Models Motor: Aluminum Air Motor Outside Dimension: 17.68" W x 30.67" H Solids (Inches): 5/16" (8 mm) Type: 852229 Valve / Seat / O-Ring: Buna-N   Ships Via Truck Contact US for a shipping quote.    

Haight Pump 10U-N Pump W/Neo Lip Sl No R/V Features Pump Body:Ductile Iron Shaft Seal:Neoprene Lip Seal  Port Size:Inlet Port is 1 inch NPT Discharge Port is 1 inch NPT GPM 10   The Haight 10U-N is a Ductile Iron Gear Pump, square flanged Pump End Only less motor, 10 GPM rated, with Ductile Iron Construction, Neoprene Lip Seal, Steel Shaft, Steel Gears, Iron Rotor and Bearings. The standard construction materials of this pump are Ductile Iron Housing, Steel Shaft and Pinion Gears, Iron Rotor and Bearings, Buna N Lip Seals and Elastomers. These gear pumps have a Gear within a gear internal design and is very effective at handling a broad range of applications while operating at standard motor speeds, and reducing wear. Both of these operating characteristics play an important role in minimizing overall capital investment, and operating expenses. Compact rugged, and easy to maintain, these pumps are ideally suited to close-coupled mounting, or direct mounting to the motor. These pumps can operate at standard motor speeds, eliminating the need for pulleys/gear reducers. The involute gear design offers excellent suction characteristics, and minimizes noise and reduces internal bypassing It comes standard with self-lubricating gramix iron bearings, and easy to maintain Buna-N lip seals. The seals are installed in the UniverSeal design for simple and quick replacement, or change to alternate seal style. This is just the bare pump end, but there are optional mounting brackets which are designed for in-line mounting with standard NEMA frame size motors or bedplate mounting. These pumps are self-priming and will develop up to 27 inches of vacuum. Pumps will operate in either direction, and flow direction in the pump can be changed without disrupting the attached piping, or special tools. The is the standard pump model and it does not come with the relief valve but if required it has the flexibility of a bolt-on, integral Relief Valve assembly (sold as an extra adder) - the relief valve assembly can be added at any time, in the field, with no special tools.   Applications Petroleum Products, Machine Manufacturing Applications Machine Tools, Hydraulic Equipment Lubrication Systems Diesel Engines Food Processing Restaurant Equipment Misc. Chemical Applications Glue and Ink Soap and Detergent Products Building and Highway Contractors Paper Products Industries Automotive Applications Shipbuilding Applications Beverage Applications Aircraft Applications Mining Applications