Flotec FP3212 3-Wire 4 Inch Submersible Well Pump, 230 Volts 1/2 HP, 10 GPM 4" Submersible Pumps are the most economical, energy-efficient pumps for 4" wells or larger. They provide the optimum amount of water and pressure for general home and farm use.   KEY FEATURES For 4" inside diameter or larger wells Pumps from depths of 150ft Floating Stack Design for sand resistance and reduced sand locking Corrosion-resistant stainless steel pump and motor housing   3 year limited warranty HORSEPOWER:  1/2 PERFORMANCE SERIES:  10 GPM VOLTAGE:  230v, 60 Hz NUMBER OF WIRES:  3 plus ground BODY CONSTRUCTION:  Stainless steel MAXIMUM CAPACITY:  14 GPM OPERATING RANGE:  20' to 150' MAXIMUM DEPTH-TO-WATER:  150' MAX PSI:  105 psi PUMP DIAMETER:  3.78" DISCHARGE PIPE SIZE:  1-1/4" NPT RECOMMENDED BREAKER:  10 amp

Flotec FP2212 2-Wire 4 Inch Submersible Well Pump, 230 Volts 1/2 HP 4" Submersible Pumps are the most economical, energy-efficient pumps for 4" wells or larger. They provide the optimum amount of water and pressure for general home and farm use.   KEY FEATURES For 4" inside diameter or larger wells Pumps from depths of 150ft Floating Stack Design for sand resistance and reduced sand locking Corrosion-resistant stainless steel pump and motor housing   3 year limited warranty HORSEPOWER:  1/2 PERFORMANCE SERIES:  10 GPM VOLTAGE:  230v, 60 Hz NUMBER OF WIRES:  2 plus ground BODY CONSTRUCTION:  Stainless Steel MAXIMUM CAPACITY:  13.6 GPM OPERATING RANGE:  20' to 150' MAXIMUM DEPTH-TO-WATER:  150' MAX PSI:  105 psi PUMP DIAMETER:  3.78" DISCHARGE PIPE SIZE:  1-1/4" NPT RECOMMENDED BREAKER:  10 amp

Flotec FP2211 2-Wire 4 Inch Submersible Well Pump, 115 Volts 1/2 HP 4" Submersible Pumps are the most economical, energy-efficient pumps for 4" wells or larger. They provide the optimum amount of water and pressure for general home and farm use.   KEY FEATURES For 4" inside diameter or larger wells Pumps from depths of 150ft Floating Stack Design for sand resistance and reduced sand locking Corrosion-resistant stainless steel pump and motor housing   WARRANTY   3 year limited warranty     HORSEPOWER:  1/2   PERFORMANCE SERIES:  10 GPM   VOLTAGE:  115v, 60 Hz   NUMBER OF WIRES:  2 plus ground   BODY CONSTRUCTION:  Stainless Steel and Thermoplastic   MAXIMUM CAPACITY:  13.6 GPM   OPERATION RANGE:  20' to 150'   MAXIMUM DEPTH-TO-WATER:  150'   MAX PSI:  105 psi   PUMP DIAMETER:  3.78"   DISCHARGE PIPE SIZE:  1-1/4" NPT     RECOMMENDED BREAKER:  25 amp

Flotec FP5182 Thermoplastic Sprinkler Pump 2 HP Corrosion-resistant, self priming sprinkler pumps are constructed of rugged, heavy-duty fiberglass-reinforced thermoplastic. Capable of operating up to 30 sprinkler heads. KEY FEATURES Superior performance at depths to water of 20' or less Fiberglass-reinforced thermoplastic pump housing for the highest corrosion resistance Ready-to-install 230 volt motor (dual voltage) Self-priming after pump housing is initially filled (Check Valve or Foot Valve required) 1 year limited warranty BODY CONSTRUCTION:  Thermoplastic HORSEPOWER:  2 MAXIMUM CAPACITY:  69 GPM FLOW AT 10' LIFT and 30 PSI:  45 GPM MAX LIFT:  25' MAXIMUM PRESSURE:  50 psi SUCTION PIPE SIZE:  2" NPT DISCHARGE PIPE SIZE:  2" NPT AMP DRAW:  12 amps on 230v / 24 amps on 115v VOLTAGE:  230v / 115v, 60 Hz RECOMMENDED BREAKER:  15 amp for 230v / 30 amp for 115v MAXIMUM WATER TEMPERATURE:  140 °F (60 °C)

Flotec FP217-811 Control Box for 3/4HP Pumps  For use with Flotec Submersible Sump Pump, Model FP3222 Controls the start and run functions  

Flotec FP2122 Submersible Well Pump 4" Flotec Submersible Well Pump, for 5" or Larger Wells, Stainless Steel Pump and Motor Housing, 7GPM Series, 2 Wire, 3/4HP 230V, 1-1/4”NPT Port, Water Filled Submersible Motor, Built-in Check Valve, No Control Box Required

Flotec FP2112 Submersible Well Pump 4" Flotec  Submersible Well Pump, for 5" or Larger Wells, Stainless Steel Pump and Motor Housing, 7GPM Series, 2 Wire, 1/2HP 230V, 1-1/4”NPT Port, Water Filled Submersible Motor, Built-in Check Valve, No Control Box Required

Flotec FP5162 Thermoplastic Sprinkler Pump 1 HP Corrosion-resistant, self priming sprinkler pumps are constructed of rugged, heavy-duty fiberglass-reinforced thermoplastic. Capable of operating up to 30 sprinkler heads. KEY FEATURES Superior performance at depths to water of 20' or less Fiberglass-reinforced thermoplastic pump housing for the highest corrosion resistance Ready-to-install 230 volt motor (dual voltage) Self-priming after pump housing is initially filled (Check Valve or Foot Valve required) WARRANTY 1 year limited warranty BODY CONSTRUCTION:  Thermoplastic HORSEPOWER:  1 MAXIMUM CAPACITY:  55 GPM FLOW at 10' LIFT and 30 PSI:  28 GPM MAX LIFT:  25' MAXIMUM PRESSURE:  42 psi SUCTION PIPE SIZE:  1-1/2" NPT DISCHARGE PIPE SIZE:  1-1/2" NPT AMP DRAW (full load):  7.4 amps on 230v / 14.8 amps on 115v VOLTAGE:  230v / 115v, 60 Hz RECOMMENDED BREAKER:  15 amp on 230v / 20 amp on 115v   MAXIMUM WATER TEMPERATURE:  140 °F (60 °C)

Flotec FP5172 Thermoplastic Sprinkler Pump 1.5 HP Corrosion-resistant, self priming sprinkler pumps are constructed of rugged, heavy-duty fiberglass-reinforced thermoplastic. Capable of operating up to 30 sprinkler heads. KEY FEATURES Superior performance at depths to water of 20' or less Fiberglass-reinforced thermoplastic pump housing for the highest corrosion resistance Ready-to-install 230 volt motor (dual voltage) Self-priming after pump housing is initially filled (Check Valve or Foot Valve required) 1 year limited warranty   BODY CONSTRUCTION:  Thermoplastic HORSEPOWER:  1-1/2 MAXIMUM CAPACITY:  67 GPM FLOW at 10' LIFT and 30 PSI:  45 GPM MAX LIFT:  25' MAXIMUM PRESSURE:  47 psi SUCTION PIPE SIZE:  1-1/2" NPT DISCHARGE PIPE SIZE:  1-1/2" NPT AMP DRAW (full load):  9.6 amps on 230v / 19.2 amps on 115v VOLTAGE:  230v / 115v , 60 Hz RECOMMENDED BREAKER:  15 amp for 230v / 25 amp for 115v MAXIMUM WATER TEMPERATURE:  140 °F (60 °C)    

Gianneschi MAXI SUB Bilge Pump 230/50 Submersible Bilge Pump for seawater and grey water.   Maxi Sub   230v 50 Hz - 0,18 kW Max flow: 180 L/min @ 2 m Max head: 8 m @ 30 L/min Outlet: 1", female (vertical) Stainless steel shaft (AISI 316) ; ABS open impeller Diameter: 230 mm Height: 350 mm IP rating : IP68

Flotec FP4122 Well Pump 3/4Hp 115/230V Flotec Shallow Well Jet Pump, Cast Iron Construction, 3/4HP 115/230V, 1-1/4”NPT Suction x 1” NPT Discharge Ports, up to 14.4GPM at 40psi, Pressure Switch Set to 30psi On / 50psi Off, up to 25 Foot Water Depth

Flotec Stainless Steel Waterfall Utility 1/2 HP Stainless Steel construction with a ceramic seal design marks the FPOS4100X as the top of the line in the Flotec Waterfall/utility series of pumps.   KEY FEATURES Complete stainless steel construction - superior corrosion resistance Seal design - allows for continuous operation High performance - ideal for waterfalls and streams WARRANTY 2 year limited warranty BODY CONSTRUCTION:  Stainless Steel HORSEPOWER:  1/2 MAXIMUM LIFT:  30' MAXIMUM CAPACITY:  4100 GPH FLOW at 10' LIFT:  3000 GPM SWITCH TYPE:  No Switch (Manual Operation) DISCHARGE PIPE SIZE:  1-1/4" (ships with Adapter Fittings) AMP DRAW (full load):  7.2 Amps CORD LENGTH:  15' VOLTAGE:  115v AC, 60 Hz MAXIMUM WATER TEMPERATURE:  100°F (38°C)

Jabsco 53041-2003-230 Pump 230V 50Hz Heavy Duty Utility 1" Self-Priming Flexible Impeller Pump 230 volt, single phase, 50Hz IP54 Electric Motor, Nitrile oil-resistant impeller   Connections: 1” BSP internal threaded ports Output: up to 9.5 GPM Built-in dry-running protection for up to 30 minutes after initial prime Rapid self-priming from dry up to 2m Will handle hard or soft solids Corrosion resistant bronze body, stainless steel shaft Carbon-ceramic mechanical shaft seal Simple, fully serviceable design with few wearing parts Continuously rated motor

March 893-10 Brushless 24V DC Pump Applications for the March 893-10 Magnetic Drive Pump include computer cooling, photographic processing equipment, refrigeration systems, and water displays.   March Pump's industrial 893-10 is an American submersible seal-less centrifugal magnetic drive pump ideal for applications such as chemical recirculation, chemical transfer, and heat transfer. It is capable of generating a maximum flow of 2.7 gallons per minute at 1 foot, and its maximum head is 10.6 Feet (or around 4.5PSI).  The pump may be used submerged or not submerged. The standard wet end (the materials that come into contact with the solution) is composed of Noryl, Nylon, Carbon/Teflon, Buna N, Stainless Steel, and Ceramic Magnet.  When submerged Epoxy, Delrin, and the motor leads are also in contact with the solution. The inlet connection is 0.375 inch female pipe thread, and the outlet is 0.375 inch smooth. The standard motor is a 0.006 Horsepower DC Brushless Motor, available in 24 Volts.  The 24 Volt Motor has an operating range from 12 to 28 Volts.  The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheit or 87 Celsius when not submerged, or 130 Fahrenheit or 54 Celsius when submerged. The March 893-10 centrifugal magnetic drive pump is capable of handling mildly or highly corrosive chemicals, acids, and solvents.   Max Flow 2.7 GPM 11 LPM Max Head 10.6 FT 3.3 M Power .006 HP .004 KW Electrical 24V Range 12-28V Submersible Yes   Type Centrifugal Mag Drive Inlet 3/8"FPT Outlet 3/8"OD Wet End Noryl (Front and Rear Housings), Nylon (Impeller), Carbon/Teflon (Thrust Washer), Buna N (O-Ring), 316 Stainless Steel (Shaft), Ceramic Magnet Uses Submersible or Open Air When submerged, the following is also in contact with the solution Epoxy, Delrin, Motor Leads    

Little Giant Pump 582614 Little Giant TE-4-MD-HC 230V Magnetic Drive Pump Motor 230 Volt 50/60 Hz 1/10 HP Totally Enclosed Fan Cooled Motor, 850 GPH at 1 Foot Head, Shutoff Head 24.3 Feet, Inlet: 1" FNPT, Outlet: 1/2" MNPT, Ryton Body, Fluid Temperature Up to 200F (93C), UR/C-CSA Listed, 6 Foot Power Cord- No Plug   582614 Magnetically driven pumps for circulation of highly corrosive acids, alkalis, solvents, brine, plating solutions, sterile solutions, and other highly corrosive chemicals and solutions that are compatible with the pump's material of construction. The MD-HC Series features leakproof, seal-less magnetic drives and are designed for in-line, non-submersed use.