Big Stick 48" - Carbon - 7/8" Shaft Light, Stiff, Rugged - Precise Helm Control The rugged, light weight tiller extensions are built to last the test of time on any go-fast dinghy or keel boat. They are simple, yet elegant. Nothing to go wrong. 7/8” diameter shaft for a sold grip for either men or women. NO Frills, just an extension! Black only. All straight tubes so that they can be modified by each sailor to tailor fit his/her boat. All come with our proven “speed lock” design for quick mount/dismount and easy replacement if necessary.  The extensions are shipped loose for custom lengths to suit your class requirements. Simply cut the tube to length and epoxy the “speed lock” fitting on to the end of the tube.

Big Stick 72" - Carbon - 7/8" Shaft Light, Stiff, Rugged - Precise Helm Control  The rugged, light weight tiller extensions are built to last the test of time on any go-fast dinghy or keel boat. They are simple, yet elegant. Nothing to go wrong. 7/8” diameter shaft for a sold grip for either men or women. NO Frills, just an extension! Black only. All straight tubes so that they can be modified by each sailor to tailor fit his/her boat. All come with our proven “speed lock” design for quick mount/dismount and easy replacement if necessary.  The extensions are shipped loose for custom lengths to suit your class requirements. Simply cut the tube to length and epoxy the “speed lock” fitting on to the end of the tube.

MP Pumps 25664 7/8" SHAFT

27"-48" Twist-Lock Steering Control Arm Fits 7/8"-1" Wheels Forespar's quick-release Steering Control Arm extends functional range when behind the wheel. Made specifically for use while motoring or easy sailing, the control arm allows the driver to move away from the helm station and still control the steering. This extended range of movement has two specific benefits. First, it enhances safety by allowing the helmsman to move outboard to the rail, increasing their forward sightline. This is especially helpful when trying to see around large headsails. Second, it allows for a number of new sitting positions for additional comfort. On many boats this means the driver can now safely relax on the stern rail seat. The Forespar Steering Control Arm uses a twist-lock extension with a special quick-release attachment clamp mounted to the wheel. It installs in seconds and can be easily deployed or removed with the simple push of a button.

PSS Shaft Seal 1-3/8" Shaft 2-1/4" Tube Shaft Diameter: 1-3/8" Stern Tube Diameter (D): 2-1/4" to 2-3/8" Total Length (A): 7.38" Total Length (compressed) (Compressed A): 6.38" Rotor Diameter (B): 2.875" Carbon Cuff Diameter (C): 2.5" Stern Cuff Length (E): 1.5" The PSS Shaft Seal is the number one selling marine mechanical seal worldwide and is installed as standard equipment by many of the worlds most reputable boat builders / yards. The PSS Shaft Seal is also recognized as the premiere retrofit (aftermarket) seal on the world market. Certified by Bureau Veritas, ABS & Rina: Boat builders / yards recognize the advantages and value of installing the PSS as it eliminates the maintenance, constant adjustment & cost associated with traditional packing type glands. Aside from these benefits, the PSS Shaft Seal helps to eliminate water in the bilge (100% water tight) & wear to the propeller shaft. The PSS Shaft Seal can be easily retrofitted and is available for shafts ranging from 3/4" (20mm) to 6" (150mm). The PSS Shaft Seal is a mechanical face seal that is created between the flat surfaces of the rotating stainless steel rotor and the stationary carbon flange. The stationary carbon flange is attached to the vessels stern tube with hose clamps and the carbon flange is attached to the front side of the bellows with hose clamps. The stainless steel rotor is fit on the shaft in front of the carbon flange. The stainless steel rotor is used to compress the bellows before the collar is secured to the shaft with set-screws. This compression (pre-load) maintains contact between the faces and allows the PSS to compensate for the thrust from the propeller. The carbon flange is bored larger than the shaft diameter allowing it to "float" around the shaft and thus compensate for most misalignment and vibration problems. The stainless steel collar is sealed to the shaft by two o-rings that are recessed into the bore of the collar. These o-rings rotate with the shaft and stainless steel rotor and do not experience wear during operation. **As with any rubber hose below waterline, the PSS bellows must be inspected on a regular basis for any sign of wear, aging or chemical deterioration. PYI suggests as preventative maintenance that the PSS bellow be replaced in six year intervals. During bellows replacement it is recommended the o-rings & set screws in the stainless steel rotor also be replaced." Bellows may need to be more frequently inspected in an environment where non-sealed batteries emit sulfuric acid. Sulfuric acid vapor will accelerate rubber deterioration, as will an ozonater. The Maintenance Kit includes the items you need to properly maintain your PSS Shaft Seal. Included in the kit is one (1) PSS bellow, two (2) O-rings, five (5) set screws, four (4) new hose clamps and an allen key.

Impeller Kit - 8 Blade - Neoprene - 2-9/16" Diameter x 3" W, 5/8" Shaft Diameter Features: Material: Neoprene Drive Type: Spline Drive Number of Blades: 8 Dimensions: Diameter: 2-9/16", Shaft Width: 3", Shaft Diameter: 5/8" Insert Material: Brass Jabsco flexible impellers can be fitted to most makes and models of bronze flexible impeller engine cooling, bilge, transfer and general purpose pumps. Jabsco flexible impellers are subjected to rigorous quality processes to ensure reliable, efficient and long lasting performance. Replace all impellers at least once every year, or sooner, depending on the engine duty. When the installation is correct an impeller may last for several years, but it is always advisable to stick to a schedule of preventative, rather than corrective, maintenance. Replacing impellers is easy. By removing the end cover screws, it is possible to remove the impeller by using either a Jabsco Impeller Removal Tool, or channel lock pliers, to grip the hub of the impeller. Don?t use screwdrivers as they may damage the face of the pump body, causing leaks, and they can be dangerous in confined spaces. Always carry spare impellers on board in case of emergency. The impeller is one of the most vital components of the engine cooling system and should always be treated as such. Always grease new impellers. Firstly, it makes it easier to install the impeller into the pump bore, and secondly it gives added protection to the impeller during initial prime. After replacing the gasket and end cover the pump is ready to use. WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Impeller Kit - 8 Blade - Neoprene - 2-9/16" Diameter x 2" W, 5/8" Shaft Diameter Features: Material: Neoprene Drive Type: Spline Drive Number of Blades: 8 Dimensions: Diameter: 2-9/16", Shaft Width: 2", Shaft Diameter: 5/8" Insert Material: Brass Jabsco flexible impellers can be fitted to most makes and models of bronze flexible impeller engine cooling, bilge, transfer and general purpose pumps. Jabsco flexible impellers are subjected to rigorous quality processes to ensure reliable, efficient and long lasting performance. Replace all impellers at least once every year, or sooner, depending on the engine duty. When the installation is correct an impeller may last for several years, but it is always advisable to stick to a schedule of preventative, rather than corrective, maintenance. Replacing impellers is easy. By removing the end cover screws, it is possible to remove the impeller by using either a Jabsco Impeller Removal Tool, or channel lock pliers, to grip the hub of the impeller. Don?t use screwdrivers as they may damage the face of the pump body, causing leaks, and they can be dangerous in confined spaces. Always carry spare impellers on board in case of emergency. The impeller is one of the most vital components of the engine cooling system and should always be treated as such. Always grease new impellers. Firstly, it makes it easier to install the impeller into the pump bore, and secondly it gives added protection to the impeller during initial prime. After replacing the gasket and end cover the pump is ready to use. WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Impeller Kit - 10 Blade - Neoprene - 2" Diameter x 7/8"W Pin Drive Insert Material: Neoprene Insert Material:Brass Drive Type: Slotted Shaft Pin Drive or Through Hole Pin Drive Number of Blades: 10 Dimensions: Diameter:2" Shaft Width:1/2" Shaft Diameter:7/8" Jabsco flexible impellers can be fitted to most makes and models of bronze flexible impeller engine cooling, bilge, transfer and general purpose pumps. Jabsco flexible impellers are subjected to rigorous quality processes to ensure reliable, efficient and long lasting performance. Replace all impellers at least once every year, or sooner, depending on the engine duty. When the installation is correct an impeller may last for several years, but it is always advisable to stick to a schedule of preventative, rather than corrective, maintenance. Replacing impellers is easy. By removing the end cover screws, it is possible to remove the impeller by using either a Jabsco Impeller Removal Tool, or channel lock pliers, to grip the hub of the impeller. Don?t use screwdrivers as they may damage the face of the pump body, causing leaks, and they can be dangerous in confined spaces. Always carry spare impellers on board in case of emergency. The impeller is one of the most vital components of the engine cooling system and should always be treated as such. Always grease new impellers. Firstly, it makes it easier to install the impeller into the pump bore, and secondly it gives added protection to the impeller during initial prime. After replacing the gasket and end cover the pump is ready to use. WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

PP4406 PowerPod Pre-Cut f/Simrad NSS7 evo2 or B&G Zeus2 7 - Carbon Black PP4400 Series, PowerPods for Power are a better option than bracket mounting. PowerPods provide a clean look for flush mounting with the advantage of a swivel base. The trunion bracket that is supplied with most electronics is not optimal. PowerPods have the advantage of protecting the back of the electronics from harsh saltwater spray. Most manufacturers do an excellent job of protecting the face of the display from water intrusion with sealed rubber push buttons. The back is generally not waterproof. They are expecting you to flush mount it into the console or a NavPod. The PowerPod also protects the plastic connectors and wires from deterioration caused by long term exposure to UV. PowerPods for Sail are for mounting on a flat surface. Perhaps under the dodger or aft end of the cockpit table especially on boats with dual wheels. Sizing: Overall Size: 9"H x 10.2"W x 6"D Usable Face: 5.6"H x 8.9"W x 3.75"D Max Cutout: 4.625"H x 8"W All PowerPods Include: Acrylic capped ABS plastic Chromed stainless steel tamper-poof fasteners Double seal for watertight integrity Models are available pre-cut for popular electronics Swivel Base with large pass-through for wire harness

PED4900 PedestalPod Uncut (Usable Face = 12.5"W x 7.8"H) (31.75cm W x 19.8cm H) - Carbon Black PedestalPods are better than bracket mounting. Very sturdy and secure, yet clean and attractive, this mount provides protection of your fishfinder/chartplotter from the harshest of wet boating conditions. PedestalPods provide the convenience of easily reaching and controlling the fishfinder/chartplotter while providing added security with protection from theft. PedestalPods position your fishfinder/chartplotter at 20" off the deck and located near the bow and at the 45° angle for ease of viewing while fishing. This allows the user to easily reach and access the fishfinder/chartplotter for changes to range, zoom or even control the trolling motor. PedestalPods are manufactured with a double gasket system that provides an excellent watertight seal keeping spray off the electrical connections on the back of your fishfinder/chartplotter assuring reliability and longevity of your marine electronics. Your fishfinder/chartplotter is easily flush mounted into the pre-cut face of the NavPod. The heavy duty, powder coated aluminum pedestal tube is 3” in diameter with a 5” round base and has a large 1.75” opening providing plenty of room for running wires and connectors internally for a very clean look and provides protection for wires and electrical connectors from water intrusion, UV exposure or damage from just getting kicked or snagged and ripped out of their sockets. NavPods come with a security wrench and nickel chrome-plated stainless steel tamperproof screws for protection from theft. There are pre-cut models available for 7", 9" and 12" LCD displays from all major marine electronic manufacturers.

PED5100-01 PedestalPod Pre-Cut f/Humminbird HELIX 10 & HELIX 9 Series - Carbon Black PedestalPods are better than bracket mounting. Very sturdy and secure, yet clean and attractive, this mount provides protection of your fishfinder/chartplotter from the harshest of wet boating conditions. PedestalPods provide the convenience of easily reaching and controlling the fishfinder/chartplotter while providing added security with protection from theft. PedestalPods position your fishfinder/chartplotter at 20" off the deck and located near the bow and at the 45° angle for ease of viewing while fishing. This allows the user to easily reach and access the fishfinder/chartplotter for changes to range, zoom or even control the trolling motor. PedestalPods are manufactured with a double gasket system that provides an excellent watertight seal keeping spray off the electrical connections on the back of your fishfinder/chartplotter assuring reliability and longevity of your marine electronics. Your fishfinder/chartplotter is easily flush mounted into the pre-cut face of the NavPod. The heavy duty, powder coated aluminum pedestal tube is 3” in diameter with a 5” round base and has a large 1.75” opening providing plenty of room for running wires and connectors internally for a very clean look and provides protection for wires and electrical connectors from water intrusion, UV exposure or damage from just getting kicked or snagged and ripped out of their sockets. NavPods come with a security wrench and nickel chrome-plated stainless steel tamperproof screws for protection from theft. There are pre-cut models available for 7", 9" and 12" LCD displays from all major marine electronic manufacturers.

PP5100-01 PowerPod Pre-Cut f/Humminbird HELIX 10 & HELIX 9 Series - Carbon Black All PowerPods Include: Acrylic capped ABS plastic Chromed stainless steel tamper-poof fasteners Double seal for watertight integrity Models are available pre-cut for popular electronics Swivel Base with large pass-through for wire harness The Hi-Gloss Material NavPods are manufactured with a custom co-extruded acrylic capped ABS material. We use the absolute best UV resistant material that provides a very high gloss white finish that matches gel-coated fiberglass. The Gen3 enhancements now include a thicker gauge material that improves strength and provides for better structural rigidity. The Waterproof Seal All NavPods are manufactured with a double gasket system providing an excellent watertight seal between the front and back of the NavPod for protection of your Marine Electronics. NavPods are made to withstand the harshest of wet offshore boating conditions. Gen3 enhancements include a thicker external silicone gasket with improved flush fit. The internal EPDM gasket is now 50% thicker and is not subject to "compression set" like many rubber compounds. This is important when you need to open the NavPod in the future to service your electronics. The Nickel Chrome Plated Screws We use all stainless steel mounting hardware that is supplied with each NavPod. Large round head tamperproof screws have deeper sockets for the NavPod wrench for better holding ability when tightening than the previous screws. For Gen3 we provide nickel chrome-plated stainless steel tamperproof screws for security combined with a little bling! The Manufacturing Process Heavy-gauge thermoforming is considered an art since many processes come into play. It all starts with the design and development of the tooling. We are fortunate to have experienced in-house design engineers who utilize CAD programs like Solidworks, Catia and AutoCad. Surfcam is used to interface with our CNC machining centers to produce quality tools with precision tolerances. Our Commitment to Quality We are committed to producing the best possible waterproof housing for Marine Electronics. Now with two decades of experience under our belt, we are confident you will have years of trouble free service and a long lasting high gloss finish. We will stand behind our commitment by now offering a 10-year warranty on all new Gen3 NavPods.

UC128TS Version 2 Hydraulic Cylinder 1.38" Bore 7.8" Stroke Front #2 Link Arm Front Mount Features: The replaceable triple-sealed 1 3/4" cylinder end cartridges offer industry-leading longevity and durability Designed for up to 600HP in certain applications 304 electropolished and passivated link assembly for peak corrosion resistance Carbon-steel piston allows less internal bypass and provides greater efficiency Ultrabolt high-strength stainless steel tiller bolt Specifications: Application: Outboard Dimensions: 3"H x 6"D x 27"L Horsepower: Up to 300 Horsepower

March 0157-0033-1000 Carbon Bushing 8 Series  

Teak Marine Lumber Thickness: 7/8" Width: 1-3/4" Length: 48"