Danfoss 180B3043 App1.5 Piston High Pressure Pump Danfoss APP1.5 180B3043 Axial Piston High Pressure Pump for salt water application, such as, seawater desalination.   Ambient temperature [°C] [Max]: 50 °C Ambient temperature [°C] [Min]: 0 °C Ambient temperature [°F] [Max]: 122 °F Ambient temperature [°F] [Min]: 32 °F Body material: Duplex Country of origin: Denmark Description: Pump for sea or brackish water Displacement [cm³/rev]: 9.31 cm3/rev Displacement [in³/rev]: 0.57 in3/rev Drain connection size (metric): M6 Drain connection standard: Metric Drain connection type: Thread Flow [gpm] [Max]: 7.97 gal/min Flow [gpm] [Min]: 1.32 gal/min Flow [l/min] [Max]: 30.67 L/min Flow [l/min] [Min]: 5.06 L/min Flow [m³/h] [Max]: 1.84 m3/h Flow [m³/h] [Min]: 0.3 m3/h Gross weight: 9.17 Kg Inlet connection size [in]: 3/4 in Inlet connection standard: BSPP Inlet connection type: Thread Inlet pressure [barg] [Max]: 5 barg Inlet pressure [barg] [Min]: 0.5 barg Inlet pressure [psig] [Max]: 72.5 psig Inlet pressure [psig] [Min]: 7.3 psig Inlet pressure peak [barg] [Max]: 10 barg Inlet pressure peak [psig] [Max]: 145 psig Media temperature [°C] [Max]: 50 °C Media temperature [°C] [Min]: 2 °C Media temperature [°F] [Max]: 122 °F Media temperature [°F] [Min]: 36 °F Outlet connection size [in]: 3/4 in Outlet connection standard: BSPP Outlet connection type: Thread Outlet pressure [barg] [Max]: 80 barg Outlet pressure [barg] [Min]: 20 barg Outlet pressure [psig] [Max]: 1160 psig Outlet pressure [psig] [Min]: 290 psig Product Group: Pump Product type: APP 1.5 Seal Material: NBR Serviceable: Yes Sound pressure level [dB(A)]: 77 dBA Speed continuous[rpm] [Min]: 700 rpm Speed [rpm] [Max]: 3450 rpm Speed [rpm] [Min]: 700 rpm

DF 180B3108 Danfoss pump APP 8.2 ATEX High Pressure Pump BrandDanfoss pump TypeWater Pump Max Pressure bar80 Flow gpm33.7 Flow l/min128 Flow m3/h7.7 rpm1800 Power kW20.3     LEAD TIME 3-4 WEEKS

Danfoss 180B0020 PAHT 25 Pump Danfoss PAHT high-pressure pumps are designed for ultra-pure water. PAHT pumps are developed for cleaning applications in the manufacturing of electronic parts (LCD and LED) and parts in the automobile industry, as well as in adiabatic cooling- and humidification systems. Lubrication of the moving parts is provided by the water itself. PAHT pumps are the lightest and most compact pumps in the industry and can be installed horizontally or vertically. They are powered by electric motors or combustion engines and are suitable for boosted inlet pressure and water supply from tank. There is no need for cooling circuits due to very high mechanical efficiency.   Benefits Zero risk of oil contamination thanks to the pump’s ultra-clean technology where no oil is needed Low maintenance costs thanks to its efficient design and stainless steel construction. Service intervals up to 8,000 hours can be expected. Low energy costs due to its highly efficient axial piston design. Easy installation. Fulfills the stringent hygiene requirements, VDI 6022, HACCP.ISO 9001, ISO 14001 and ATEX certified.   Ambient temperature [°C] [Max]: 50 °C Ambient temperature [°C] [Min]: 0 °C Ambient temperature [°F] [Max]: 122 °F Ambient temperature [°F] [Min]: 32 °F Body material: AISI 316 Country of origin: Denmark Description: Pump for ultra pure water Displacement [cm³/rev]: 25 cm3/rev Displacement [in³/rev]: 1.53 in3/rev Drain connection size (metric): M6 Drain connection standard: Metric Drain connection type: Thread Flow [gpm] [Max]: 13.57 gal/min Flow [gpm] [Min]: 3.38 gal/min Flow [l/min] [Max]: 52.2 L/min Flow [l/min] [Min]: 12.99 L/min Gross weight: 23.31 Kg Inlet connection size [in]: 1 1/4 in Inlet connection standard: BSPP Inlet connection type: Thread Inlet pressure [barg] [Max]: 6 barg Inlet pressure [barg] [Min]: 0 barg Inlet pressure [psig] [Max]: 87 psig Inlet pressure [psig] [Min]: 0 psig Inlet pressure peak [barg] [Max]: 20 barg Inlet pressure peak [psig] [Max]: 290 psig Media temperature [°C] [Max]: 50 °C Media temperature [°C] [Min]: 2 °C Media temperature [°F] [Max]: 122 °F Media temperature [°F] [Min]: 36 °F Outlet connection size [in]: 3/4 in Outlet connection standard: BSPP Outlet connection type: Thread Outlet pressure [barg] [Max]: 160 barg Outlet pressure [barg] [Min]: 30 barg Outlet pressure [psig] [Max]: 2320 psig Outlet pressure [psig] [Min]: 435 psig Product Group: Pump Product type: PAHT 25 Seal Material: NBR Serviceable: Yes Sound pressure level [dB(A)]: 79 dBA Speed continuous[rpm] [Min]: 1000 rpm Speed [rpm] [Max]: 2400 rpm Speed [rpm] [Min]: 700 rpm   Type: PAHT

Danfoss 180B3045 App 2.2 Piston High Pressure Pump Ambient temperature [°C] [Max]: 50 °C Ambient temperature [°C] [Min]: 0 °C Ambient temperature [°F] [Max]: 122 °F Ambient temperature [°F] [Min]: 32 °F Body material: Duplex Country of origin: Denmark Description: Pump for sea or brackish water Displacement [cm³/rev]: 12.52 cm3/rev Displacement [in³/rev]: 0.76 in3/rev Drain connection size (metric): M6 Drain connection standard: Metric Drain connection typeThread Flow [gpm] [Max]: 10.9 gal/min Flow [gpm] [Min]: 1.95 gal/min Flow [l/min] [Max]: 41.92 L/min Flow [l/min] [Min]: 7.49 L/min Flow [m³/h] [Max]: 2.52 m3/h Flow [m³/h] [Min]: 0.45 m3/h Gross weight: 9.14 Kg Inlet connection size [in]: 3/4 in Inlet connection standard: BSPP Inlet connection type: Thread Inlet pressure [barg] [Max]5 barg Inlet pressure [barg] [Min]0.5 barg Inlet pressure [psig] [Max]72.5 psig Inlet pressure [psig] [Min]7.3 psig Inlet pressure peak [barg] [Max]10 barg Inlet pressure peak [psig] [Max]145 psig Media temperature [°C] [Max]: 50 °C Media temperature [°C] [Min]: 2 °C Media temperature [°F] [Max]: 122 °F Media temperature [°F] [Min]: 36 °F Outlet connection size [in]: 3/4 in Outlet connection standardBSPP Outlet connection type: Thread Outlet pressure [barg] [Max]: 80 barg Outlet pressure [barg] [Min]: 20 barg Outlet pressure [psig] [Max]: 1160 psig Outlet pressure [psig] [Min]: 290 psig Product Group: Pump Product type: APP 2.2 Seal Material: NBR Serviceable: Yes Sound pressure level [dB(A)]: 77 dBA Speed continuous[rpm] [Min]: 700 rpm Speed [rpm] [Max]: 3450 rpm Speed [rpm] [Min]: 700 rpm  

The US Coast Guard issued a safety alert advising of a potential problem involving certain ANSUL – High Pressure Carbon Dioxide Fire Extinguishing Systems. There have been several instances where this system has discharged without human intervention. The manufacturer has identified the suspect CO2 cylinder valves as those having a date code between 10-07 and 06- 08. Owners, operators, and masters of ships having such ANSUL systems should immediately check the dates on the CO2 cylinder valves and notify ANSUL if the date code is within the suspect range. Safety Alert 05-09

Danfoss 180B3046 App 2.5 Pump Specifications Brand: Danfoss pump Type: Water Pump Max Pressure bar: 80 Flow gpm: 11.1 Flow l/min: 42 Rpm: 3450   Applications Desalination Irigation Water treatment Water supply

Shurflo 8005-733-255, Diaphragm Pump 3 Chamber 1.56 GPM 115VAC Shurflo Diaphragm Pump 3 Chamber, 1.56 GPM Open Flow, 115VAC Intermittant Duty, 60 PSI Demand Switch (adjustable 40-60 PSI), 45 PSI Bypass, EPDM Valves, Santoprene Diaphragm, Polypropylene Housing, 3/8" NPT Female Ports, UL/CSA Recognized, NSF Listed, Typical Application: Water Delivery   The SHURflo 8005-733-255 Demand Pump is ideal in applications that require high pressure and a flow rate of 1.5 GPM.  The pump can be mounted in any position, is compact and is designed for long trouble-free life.   1.5 GPM flow rate Demand Switch 45psi internal bypass Can run dry without damage Self priming up 8 vertical feet 3/8" NPT female ports Santoprene diaphragm Built-in check valve UL Recognized Component NSF and CSA listed

Digital High-Pressure Pump with Car Adapter Digital high-pressure DC pump. Plugs into any 12V car or boat accessory outlet. Digital gauge operation with auto-stop function when reaching max set PSI/BAR. Compatible with HR valves only. Features: 12VDC Plugs into car/boat accessory outlet Digital gauge and auto-stop function Compatible with HR valves only 16 PSI max pressure

Danfoss 180B0030 Paht4 Tech Water Pump Ambient temperature [°C] [Max]50 °C Ambient temperature [°C] [Min]0 °C Ambient temperature [°F] [Max]122 °F Ambient temperature [°F] [Min]32 °F Body materialAISI 304 Country of originDenmark DescriptionPump for ultra pure water Displacement [cm³/rev]4 cm³/rev Displacement [in³/rev]0.24 in³/rev Drain connection size (metric)M6 Drain connection standardMetric Drain connection typeThread Flow [gpm] [Max]2.63 gal/min Flow [gpm] [Min]0.78 gal/min Flow [l/min] [Max]10.12 L/min Flow [l/min] [Min]2.99 L/min Inlet connection size [in]1/2 in Inlet connection standardBSPP Inlet connection typeThread Inlet pressure [barg] [Max]4 barg Inlet pressure [barg] [Min]0 barg Inlet pressure [psig] [Max]58 psig Inlet pressure [psig] [Min]0 psig Inlet pressure peak [barg] [Max]4 barg Inlet pressure peak [psig] [Max]58 psig Media temperature [°C] [Max]50 °C Media temperature [°C] [Min]2 °C Media temperature [°F] [Max]122 °F Media temperature [°F] [Min]36 °F Outlet connection size [in]1/4 in Outlet connection standardBSPP Outlet connection typeThread Outlet pressure [barg] [Max]100 barg Outlet pressure [barg] [Min]30 barg Outlet pressure [psig] [Max]1450 psig Outlet pressure [psig] [Min]435 psig Outside dimensions of packaging LxWxH [in]10,7x5,9x5,4 Outside dimensions of packaging LxWxH [mm]274x151x137 Product groupPump Product namePAHT pumps Seal MaterialNBR ServiceableYes Sound pressure level [dB(A)]76 dBA Speed [rpm] [Max]3000 rpm Speed [rpm] [Min]1000 rpm Speed continuous [rpm] [Min]1000 rpm TYPEPAHT TypePAHT 2-6.3 Type designationPAHT 4

Danfoss 180B0024 Pah2 Pump Flow [gpm] [Max]: 0.670, Flow [l/min] [Max]: 2.590, Outlet pressure [barg] [Max]: 140, Speed [rpm] [Max]: 1800, Speed [rpm] [Min]: 700, Body material: AISI 304 Ambient temperature [°C] [Max]50 °C Ambient temperature [°C] [Min]0 °C Ambient temperature [°F] [Max]122 °F Ambient temperature [°F] [Min]32 °F Body materialAISI 304 Country of originDenmark DescriptionPAH2 Displacement [cm³/rev]2 cm³/rev Displacement [in³/rev]0.12 in³/rev Drain connection size (metric)M6 Drain connection standardMetric Drain connection typeThread Flow [gpm] [Max]0.67 gal/min Flow [gpm] [Min]0.1 gal/min Flow [l/min] [Max]2.59 L/min Flow [l/min] [Min]0.39 L/min Inlet connection size [in]1/2 in Inlet connection standardBSPP Inlet connection typeThread Inlet pressure [barg] [Max]4 barg Inlet pressure [barg] [Min]0 barg Inlet pressure [psig] [Max]58 psig Inlet pressure [psig] [Min]0 psig Media temperature [°C] [Max]50 °C Media temperature [°C] [Min]2 °C Media temperature [°F] [Max]122 °F Media temperature [°F] [Min]36 °F Outlet connection size [in]1/4 in Outlet connection standardBSPP Outlet connection typeThread Outlet pressure [barg] [Max]140 barg Outlet pressure [barg] [Min]30 barg Outlet pressure [psig] [Max]2030 psig Outlet pressure [psig] [Min]435 psig Outside dimensions of packaging LxWxH [in]10,7x5,9x5,4 Outside dimensions of packaging LxWxH [mm]274x151x137 Product groupPump Product namePAH pumps Seal MaterialNBR ServiceableYes Sound pressure level [dB(A)]76 dBA Speed [rpm] [Max]1800 rpm Speed [rpm] [Min]700 rpm Speed continuous [rpm] [Min]700 rpm TYPEPAH TypePAH 2-6.3 Type designationPAH 2

Danfoss 180B0031 PAHT 2 Tech Water Pump Flow gpm Max: 1.090 Flow l/min Max: 4.190 Outlet pressure Max: 100 Speed rpm Max: 3000 Speed rpm Min: 1000, Body material: AISI 304 Ambient temperature °F Max122 °F Ambient temperature °F Min32 °F Body material AISI 304 Country of originDenmark Description Pump for ultra pure water Drain connection standard Metric Drain connection typeThread   TYPE PAHT Type PAHT 2-6.3 Type designation PAHT 2  

Walbro FRB-13-2 Fuel Pump 6-8 Psi 12V Pressure: 6.0 - 8.0 psi Service Life: 18,000+ hr Magnetic Trap: Yes Minimum Flow Rate: 43 gph Dry Lift: 48" Current Draw: 2.3 Amp Inlet/Outlet: 1/4-18 NPSF Fuse: 5A Inlet Filter Screen: 70 Micron Weight: 1.83 lb Voltage: 12V DC Outlet Check Valve: None   The FRB is an advanced electric fuel pump with internal circuitry allowing it to operate at a variable frequency. When turned on, it will cycle as long as there is a demand for fuel, but when fuel demand decreases, the pump slows down as it builds pressure in the fuel delivery line - until the pump's rated maximum pressure is reached, and the pump stops. These FRB pumps are especially suitable for applications where battery life, low noise, and best durability are important. Not recommended for applications such as heater or stove systems as output pressures are too high. For heater and stove fuel pumps, use the lower pressure Walbro FRD Series. See Related Products, below. The FRB is designed to serve as a primary pump (replacing a mechanical fuel pump) or as an auxilliary fuel pump (assisting the existing pump) for internal combustion engines. A common application is supplying fuel to the those diesel refrigeration units mounted high on tractor-trailer trucks. These pumps incorporate a new piston mechanism which, unlike rubber diaphragms, is not affected by modern, high-tech fuel blends. • Pump cycles only when fuel is demanded - so the pump cycles on and off • The non-adjustable maximum output pressure is factory pre-set in the ranges specified in the table, below • Continuous duty life (diesel fuel): >18,000 hours • Can run dry for up to 4 hours • Flow rates as high as 60 gph, but 30 gph is a more typical maximum • Compatible with all commercially available pump grade gasoline, gasoline-alcohol blends, diesel, and bio-diesel fuels • Self-priming to 4 feet • Current draw averages less than 2 amps • USCG 16623-1 and 16623-2 approved; ignition protected • Anodized, corrosion protection coating passes 1,000 hr salt spray test - suitable for marine applications • Replaceable internal 70 micron mesh filter • Magnetic trap for ferrous contaminants • Inlet (lower, side)/Outlet (top): 1/4-18 NPSF (Dryseal American National Standard Straight Pipe Thread) — will accept NPT tapered fittings without leaking, thread sealant recommended • Dimensions: 5.83"H x 2.76"Dia. • Note - a suffix number (typically -1 or -2) in part number refers to type of packaging • Made in USA NOTE — Although the included instructions indicate that FRB pumps are supplied with hose clamps, at this time (5/8/13), these pumps do not include any installation fittings. Technical Selecting among the Walbro FR Series electric fuel pumps: • All the FR electric pumps provide fuel until the fuel demand decreases, or flow is restricted - but they have different mechanisms for doing so. FR pumps will cycle (pump) until they build up the pressure (head) in the outflow line - with an accompanying decrease in fuel flow - and reach their factory preset maximum pressure. At this point, constant frequency pumps like the FRA will continue cycling - but no fuel will flow. Variable frequency pumps, like the FRB and FRD, will slow and eventually stop cycling as the pressure builds. If the pressure on the outflow side of the pump drops, both types of pump will start supplying fuel again. • Choosing an FR Series pump is often less dependent on the application, and more a matter of user preference: — FRA pumps are lower cost, basic models. They have no built-in filter, and their constant cycling means electric current draw is constant - regardless of output, they are always making noise, they typically have a shorter lifespan (higher wear), and they can wear unevenly as the stroke can be shortened when operating near their maximal pressure. — FRB and FRD pumps have a more expensive variable frequency circuit board, always use their full stroke length - so wear is evenly distributed, do not always operate at full capacity/maximal cycling — so less wear, longer life, less noise, and lower average current draw. Additionally, the FRB models include a built-in/replaceable 70 micron mesh filter, so the user doesn't need to supply a pre-filter.   • What the FR fuel pump is designed to do: — In carbureted applications - The FRA and FRB fuel pumps self-regulate to their maximum output pressure when the carburetor bowl is full, and respond to float movement in the carburetor as required. When the engine demands more fuel, the pump increases its flow rate. When the engine demand drops, the pump reduces its flow rate. — In diesel applications - The FRA and FRB pumps will deliver fuel to the diesel injector pump, assuring a positive pressure at the injector pump inlet. These pumps are designed to refill diesel filters after service or replacement. — In transfer applications, including fuel polishing, FRA and FRB pumps run continuously, as long as electrical power is supplied to the pump, and output back pressure is low. — In diesel heater and stove applications, the task-specific FRD pumps will slow their cycling rate to deliver only the fuel required by the stove fuel metering valve ("carburetor"). FRD pumps can also fill day tanks in gravity feed installations. • Complete list of approved fuels for FR pumps: — Unleaded regular gasoline, premium gasoline, gasoline-alcohol blends, diesel fuel, bio-diesel, Stoddard solvent, E85.  

Walbro FRB-16-2 24V Fuel Pump 6-8 Psi Outlet Check Valve: None Voltage: 24V DC Weight: 1.83 lb Magnetic Trap: Yes Minimum Flow Rate: 43 gph Dry Lift: 48" Current Draw: 1.7 Amp Inlet/Outlet: 1/4-18 NPSF Fuse: 5A Inlet Filter Screen: 70 Micron Service Life: 18,000+ hr Pressure: 6.0 - 8.0 psi   The FRB is an advanced electric fuel pump with internal circuitry allowing it to operate at a variable frequency. When turned on, it will cycle as long as there is a demand for fuel, but when fuel demand decreases, the pump slows down as it builds pressure in the fuel delivery line - until the pump's rated maximum pressure is reached, and the pump stops. These FRB pumps are especially suitable for applications where battery life, low noise, and best durability are important. Not recommended for applications such as heater or stove systems as output pressures are too high. For heater and stove fuel pumps, use the lower pressure Walbro FRD Series. See Related Products, below. The FRB is designed to serve as a primary pump (replacing a mechanical fuel pump) or as an auxilliary fuel pump (assisting the existing pump) for internal combustion engines. A common application is supplying fuel to the those diesel refrigeration units mounted high on tractor-trailer trucks. These pumps incorporate a new piston mechanism which, unlike rubber diaphragms, is not affected by modern, high-tech fuel blends. • Pump cycles only when fuel is demanded - so the pump cycles on and off • The non-adjustable maximum output pressure is factory pre-set in the ranges specified in the table, below • Continuous duty life (diesel fuel): >18,000 hours • Can run dry for up to 4 hours • Flow rates as high as 60 gph, but 30 gph is a more typical maximum • Compatible with all commercially available pump grade gasoline, gasoline-alcohol blends, diesel, and bio-diesel fuels • Self-priming to 4 feet • Current draw averages less than 2 amps • USCG 16623-1 and 16623-2 approved; ignition protected • Anodized, corrosion protection coating passes 1,000 hr salt spray test - suitable for marine applications • Replaceable internal 70 micron mesh filter • Magnetic trap for ferrous contaminants • Inlet (lower, side)/Outlet (top): 1/4-18 NPSF (Dryseal American National Standard Straight Pipe Thread) — will accept NPT tapered fittings without leaking, thread sealant recommended • Dimensions: 5.83"H x 2.76"Dia. • Note - a suffix number (typically -1 or -2) in part number refers to type of packaging • Made in USA NOTE — Although the included instructions indicate that FRB pumps are supplied with hose clamps, at this time (5/8/13), these pumps do not include any installation fittings. Technical Selecting among the Walbro FR Series electric fuel pumps: • All the FR electric pumps provide fuel until the fuel demand decreases, or flow is restricted - but they have different mechanisms for doing so. FR pumps will cycle (pump) until they build up the pressure (head) in the outflow line - with an accompanying decrease in fuel flow - and reach their factory preset maximum pressure. At this point, constant frequency pumps like the FRA will continue cycling - but no fuel will flow. Variable frequency pumps, like the FRB and FRD, will slow and eventually stop cycling as the pressure builds. If the pressure on the outflow side of the pump drops, both types of pump will start supplying fuel again. • Choosing an FR Series pump is often less dependent on the application, and more a matter of user preference: FRA pumps are lower cost, basic models. They have no built-in filter, and their constant cycling means electric current draw is constant - regardless of output, they are always making noise, they typically have a shorter lifespan (higher wear), and they can wear unevenly as the stroke can be shortened when operating near their maximal pressure. FRB and FRD pumps have a more expensive variable frequency circuit board, always use their full stroke length - so wear is evenly distributed, do not always operate at full capacity/maximal cycling — so less wear, longer life, less noise, and lower average current draw. Additionally, the FRB models include a built-in/replaceable 70 micron mesh filter, so the user doesn't need to supply a pre-filter. • What the FR fuel pump is designed to do: In carbureted applications - The FRA and FRB fuel pumps self-regulate to their maximum output pressure when the carburetor bowl is full, and respond to float movement in the carburetor as required. When the engine demands more fuel, the pump increases its flow rate. When the engine demand drops, the pump reduces its flow rate. In diesel applications - The FRA and FRB pumps will deliver fuel to the diesel injector pump, assuring a positive pressure at the injector pump inlet.   These pumps are designed to refill diesel filters after service or replacement. In transfer applications, including fuel polishing, FRA and FRB pumps run continuously, as long as electrical power is supplied to the pump, and output back pressure is low. In diesel heater and stove applications, the task-specific FRD pumps will slow their cycling rate to deliver only the fuel required by the stove fuel metering valve ("carburetor"). FRD pumps can also fill day tanks in gravity feed installations. • Complete list of approved fuels for FR pumps: Unleaded regular gasoline, premium gasoline, gasoline-alcohol blends, diesel fuel, bio-diesel, Stoddard solvent, E85.  

Iwaki MD-70RLZT, 3/4 inch MPT in/outlet 684gph 220v Iwaki MD-70RLZT Water Pump   Japanese made high pressure rated pump. 3/4 inch MPT inlet and outlet. 2/7 HP Motor output. 3400 RPM motor speed. 220 Volt 1.90 amps. Max flow 11.4 GPM. 684 GPH Max head 66.6 ft. Max system pressure 42.7 psi.   Iwaki water pumps are magnetic driven, seamless pumps for use on either freshwater or saltwater aquariums. These pumps have a low heat exchange rate combined with quiet operation. Also the Iwaki pumps have a highly durable and aquarium tested design.   WMD pumps have American Made Motors MD pumps have Japanese Made Motors RLT pumps are for pressure applications RZT pumps are for very high pressure applications RLXT pumps are for circulation and wet or dry return   Iwaki America Inc. of Holliston, Massachusetts, is a joint venture which grew from a 15 year association between Walchem Corp. of Holliston, MA and Iwaki Co. Ltd. of Tokyo, Japan. Combining Walchems 30 years of chemical injection and control experience with Iwakis 50 years of pump design engineering, Iwaki America offers the best chemical handling equipment for use in Chemical Process, O.E.M., Industrial and Semiconductor applications.

SHURflo 8000-813-138, Diaphragm Pump 3 Chamber 1.47 GPM 115VAC High Pressure Carpet Pump SHURflo Diaphragm Pump 3 Chamber, 1.47 GPM Open Flow, 115VAC Intermittant Duty, 100 PSI Demand Switch (adjustable 80-100 PSI), Viton Valves, Santoprene Diaphragm, Nylon Housing, 1/2"-14 Male Parallel Thread Ports, UL/CSA Recognized,   Typical Application: Soil Extraction, Carpet Cleaning