|
Spare Vane Only f/WindTrak 15
|
30.00 |
|
|
Spare Vane Only f/WindTrak 10.Sport
|
18.76 |
|
|
J-BASE for WindTrak 15
This optional mount for WindTrak 15 provides more versatility and reduces overall weight aloft by 15 grams when substituted for standard WindTrak 15 mounting base.
The J-Base comes with two #10 (5 mm) selftapping screws. Drill a pilot hole in mast, apply silicone sealant or Locktite® and screw into mast. Installation of J-Base can also be accomplished by tapping the mast for 3/16" (5 mm) machine screws or by using epoxy putty to affix base to the mast
|
9.25 |
|
|
J-Base for WindTrak 10.Sport for Side, Top or Front of Mast Mounting
Allows for side, top, or front mounting on most masts, on big boats or dinghies alike. Standard with the WindTrak 10.Sport, J-Base™ can be ordered as an option for WindTrak 15.
Standard with the WindTrak 10.Sport, J-Base™ can be ordered as an option for WindTrak 15. Allows for side, top, or front mounting on most masts, on big boats or dinghies alike. J-Base is made of glass filled polycarbonate, 2″ (5 cm) long. Includes stainless steel set screw and (2) #10 self-tapping screws. Reduces overall weight by 15 grams when substituted for standard mounting base on WindTrak 15.
|
9.25 |
|
|
WindTrak 15
WindTrak wind vanes continue to offer exceptional performance at the best value of any wind indicator worldwide. The secret is in the sapphire jewel suspension bearing, large fin-low inertia vane, and easy-to-read, fully adjustable tacking tab system.
WindTrak is the perfect choice for all cruising and racing boats 15' (4.6 meters) and bigger.
Reflector tape on the vane and tacking tabs make WindTrak 15 easy to see day and night. WindTrak vanes are sturdy and when installed properly, offer many years of use. They have been wind tunnel tested to wind speeds of 80 knots! WindTrak 15 has a 15" (38 cm) vane. Includes through-bolt or drill and tap mounting socket; 5/16" -18 stainless stud, washers and nut. Stands 12.75" (32 cm) tall and weighs just 3.6 ounces (101 g).
A bird-proof spike extends another 10" (24 cm) above the vane to discourage birds from landing.
|
52.50 |
|
|
WindTrak AV Spare Vane Only
|
22.50 |
|
|
Universal Masthead Mount
Extend your WindTrak 10.Sport or WindTrak 15 vane away from masthead obstructions and turbulence. The 13" (33 cm) arm comes with hardware allowing side or top mounting and offset angles up to ±20 degrees. May be attached securely to flat, curved, vertical, horizontal, or inclined surfaces. Gain space aloft and improve mounting position of wind finders and other equipment. Mount on the back of the mast for easier viewing from the cockpit. The mount adapts to virtually every masthead situation.
Features:
Length 13" (33 cm)
Weight 3.2 oz (90 g)
Boom can be shortened if necessary; complete instructions included
Can be used with WindTrak Light #3200. Also accommodates Davis J-Base Mounts (using #10 stainless steel screws and nuts, not included)
|
37.50 |
|
|
Spare Cap f/1313 Gas Fill
Non-Locking Spare Cap f/1313 Gas Fill
|
10.99 |
|
|
Smart Tab Trim Tabs 9 X 8 f/13-15' Boats w/30-40 HP
IMPROVES YOUR BOAT'S OVERALL PERFORMANCE GUARANTEED!!!
If these trim tabs don't provide you with an outstanding performance increase, contact us within 30 days of your purchase.
Why buy a manually adjusting trim tab set when you can get the automatic trim tabs that will self adjust and perform better for less money?
Our breakthrough technology in trim tabs is completely automatic requiring no operator adjustment while underway. Nauticus trim tabs self adjust according to how you load and maneuver your boat.
The nitrogen Gas Actuator provides LIFT at the stern of the boat by holding the trim plate down during acceleration. The amount of LIFT is determined by the actuator load rating and the trim plate adjustment, which is done at the time of installation.
Reduce the minimum planning speed by up to 33%
Faster Acceleration
Increase top speed
Provide a level, more comfortable ride at lower speeds
Improve fuel economy, handling and safety
NO HYDRAULICS - NO ELECTRIC SWITCHES
Nauticus trim tabs are completely automatic requiring no operator adjustment while underway.
The nitrogen Gas Actuator provides LIFT at the stern of the boat by holding the trim plate down during acceleration. The amount of LIFT is determined by the actuator load rating and the trim plate adjustment, which is done at the time of installation.(see installation instruction).
SPEED REGULATED
Nauticus trim tabs start in a downward angel to maximize lift at slow speeds. As the boat accelerates, the water pushes up on the trim plates providing lift to the stern which minimizes bow rise, and allows the boat to plane quickly.
Once the water pressure exceeds the actuator load rating (maximum lift) the trim plates move up to a horizontal position eliminating any drag.
BOAT STABILIZERS
Even when cruising SMART TABS continue to work like shock absorbers. The constant adjustment to sea conditions allow SMART TABS to provide remarkable stability in turns, while crossing waves, while cruising, and while running at maximum speeds. No more sliding, porpoising, or chine walking.
ONE OF A KIND
The unique system is the only one of its kind in the industry. The internal valve system is truly "smart" in its design of controlling you boats performance.
It will reduce the minimum planning speed by 33%
Provide a level, more comfortable ride at lower speeds
Improve economy, handling and safety
As the boat speed increases, the water pressure also increases. Once the water pressure exceeds the Actuator load rating (maximum LIFT period) the trim plates begin to move upward until they are horizontal with the bottom of the boat.
The internal valve system dampens the trim plate movement which eliminates any instant reaction to minor water pressure variances. Nauticus trim tabs provide smooth and undetectable reaction to boat speed creating a level, more comfortable ride at lower speeds.
INSTALLATION IS SIMPLE
With an electric drill, small drill bit, a phillips screwdriver, and two wrenches, just about anyone can install SMART TABS in less than an hour. Professional installers should be able to install SMART TABS in 30 minutes or less.
All mounting hardware, instructions, and templates are included.
SMART TABS require NO THROUGH HULL DRILLING
|
116.16 |
|
|
F-7 - 15" x 41" - Double Layer - Navy
The F-Series are double layered making them softer, more durable & reversible.
Master Fender Covers are specially designed to protect the topsides and hull from fender scuff and reduce the need for expensive gel coat repairs.
They are made from a premium stain resistant, non-abrasive, loop-knit acrylic fabric, which is both durable and fade resistant. They are available in a variety of colors and sizes to suit your individual requirements.
|
47.99 |
|
|
F-7 - 15" x 41" - Double Layer - Black
The F-Series are double layered making them softer, more durable & reversible.
Master Fender Covers are specially designed to protect the topsides and hull from fender scuff and reduce the need for expensive gel coat repairs.
They are made from a premium stain resistant, non-abrasive, loop-knit acrylic fabric, which is both durable and fade resistant. They are available in a variety of colors and sizes to suit your individual requirements.
|
59.05 |
|
|
F-8 - 15" x 58" - Double Layer - Navy
The F-Series are double layered making them softer, more durable & reversible.
Master Fender Covers are specially designed to protect the topsides and hull from fender scuff and reduce the need for expensive gel coat repairs.
They are made from a premium stain resistant, non-abrasive, loop-knit acrylic fabric, which is both durable and fade resistant. They are available in a variety of colors and sizes to suit your individual requirements.
|
85.92 |
|
|
F-8 - 15" x 58" - Double Layer - Black
The F-Series are double layered making them softer, more durable & reversible.
Master Fender Covers are specially designed to protect the topsides and hull from fender scuff and reduce the need for expensive gel coat repairs.
They are made from a premium stain resistant, non-abrasive, loop-knit acrylic fabric, which is both durable and fade resistant. They are available in a variety of colors and sizes to suit your individual requirements.
|
85.92 |
|
|
No-Drill™ Vehicle Laptop System f/97-15 Ford Expedition
This No-Drill™ Laptop Stand System installs quickly and easily into the specified vehicles using the existing hardware of the passenger side seat rails. This configuration provides a telescoping feature that ranges from 12" to 18". Dual swing arms provide articulation and 12" of reach for passenger and driver access to the mounted device. Rubber ball and socket joint provides additional adjustment as well as shock and vibration isolation.
The RAM Tough Tray™ is spring loaded to accommodate 10" to 16" wide laptops & (17" wide screens). The tray features four adjustable retaining arms with rubber grip feature. These arms can be moved both vertically and horizontally. This allows for a custom fit for varying thicknesses of laptops and the freedom of not blocking ports or drives. A screen support and USB light are also available to accessorize the tray. Hole patterns on perimeter of tray facilitate the mounting of additional RAM systems to support GPS or other electronics.
Compatible Vehicles:
Ford Expedition (1997-2015)
Ford Expedition King Ranch EL (2013)
Ford Expedition Limited (2013)
Ford Expedition Limited EL (2013)
Ford Expedition Ranch EL (2013)
Ford Expedition XLT (2013)
Ford Expedition XLT EL (2013)
Ford F-150 (1997-2003)
Ford F-150 Heritage (2004)
Ford F-250 Light Duty (1997-2004)
Ford Windstar (2004-2007)
Specs & Features
Placement of Mount: Passenger side floor board, under seat
Drilling Requirements: No - uses existing seat bolts
Seat Configuration: Bucket/Bench
Material: High Strength Composite and Powder Coated Steel
Notes:If the Tough-Tray™ Laptop Cradle is intended to hold a laptop or device while the vehicle is in motion, we recommend the Secure-N-Motion™ kit.
One 4" riser is included with this vehicle base. Step feature allows minimized amount of intrusion of passenger leg space. This base will not interfere with factory installed console in most installations.
|
266.34 |
|
|
No-Drill™ Vehicle Laptop Base f/97-15 Ford Expedition
The RAM® No-Drill™ laptop mounting base features a heavy-duty steel mounting base custom designed to fit this vehicle perfectly. Using the front bench or passenger side seat rail bolts as attachment points, existing hardware is used to secure the laptop mount base in the vehicle.
Compatible Vehicles:
Ford Expedition (1997-2015)
Ford Expedition King Ranch EL (2013)
Ford Expedition Limited (2013)
Ford Expedition Limited EL (2013)
Ford Expedition Ranch EL (2013)
Ford Expedition XLT (2013)
Ford Expedition XLT EL (2013)
Ford F-150 (1997-2003)
Ford F-150 Heritage (2004)
Ford F-250 Light Duty (1997-2004)
Ford Windstar (2004-2007)
Specs & Features
Placement of Mount: Passenger side floor board, under seat
Drilling Requirements: No - uses existing seat bolts
Seat Configuration: Bucket/bench
Pole: Purchased Separately
Material: Powder Coated Steel
Features: One 4" riser is included with this vehicle base. Step feature allows minimized amount of intrusion of passenger leg space. This base will not interfere with factory installed console in most installations.
|
98.90 |
|