Repair parts for SeaStar hydraulic cylinders.

Male Run T-Fitting - 3/8" x 3/8" Tube x 1/4" NPT Typical Application: Used to connect any 1/4 NPT Female port to our hoses Specifications: 1/4 NPT to 3/8 COMP FITTING Helm side = 1/4 NPT Hose side= 9/16 - 24 UNEF 2A

3/8" compression fittings which utilize a 9/16"-24 fine thread. NPT fittings are not to be used in a -3 helm and/or cylinder.

Raritan 1117B Screw 3/8-16 X 1-1/8 Hx Hd

PSS Shaft Seal Maintenance & Parts Replacement Kit FOR 1 3/8" SHAFT 2 1/4" TUBE As with any rubber hose below waterline, the PSS bellows must be inspected on a regular basis for any sign of wear, aging or chemical deterioration. The PSS bellow should be replaced in six year intervals. During bellows replacement it is recommended the o-rings & set screws in the stainless steel rotor also be replaced. Bellows may need to be more frequently inspected in an environment where non-sealed batteries emit sulfuric acid. Sulfuric acid vapor will accelerate rubber deterioration, as will an ozonater. The Maintenance Kit includes the items you need to properly maintain your PSS Shaft Seal. Included in the kit is one (1) PSS bellow, two (2) O-rings, five (5) set screws, four (4) new hose clamps and an allen key.

PSS Shaft Seal 1-3/8" Shaft 2-1/4" Tube Shaft Diameter: 1-3/8" Stern Tube Diameter (D): 2-1/4" to 2-3/8" Total Length (A): 7.38" Total Length (compressed) (Compressed A): 6.38" Rotor Diameter (B): 2.875" Carbon Cuff Diameter (C): 2.5" Stern Cuff Length (E): 1.5" The PSS Shaft Seal is the number one selling marine mechanical seal worldwide and is installed as standard equipment by many of the worlds most reputable boat builders / yards. The PSS Shaft Seal is also recognized as the premiere retrofit (aftermarket) seal on the world market. Certified by Bureau Veritas, ABS & Rina: Boat builders / yards recognize the advantages and value of installing the PSS as it eliminates the maintenance, constant adjustment & cost associated with traditional packing type glands. Aside from these benefits, the PSS Shaft Seal helps to eliminate water in the bilge (100% water tight) & wear to the propeller shaft. The PSS Shaft Seal can be easily retrofitted and is available for shafts ranging from 3/4" (20mm) to 6" (150mm). The PSS Shaft Seal is a mechanical face seal that is created between the flat surfaces of the rotating stainless steel rotor and the stationary carbon flange. The stationary carbon flange is attached to the vessels stern tube with hose clamps and the carbon flange is attached to the front side of the bellows with hose clamps. The stainless steel rotor is fit on the shaft in front of the carbon flange. The stainless steel rotor is used to compress the bellows before the collar is secured to the shaft with set-screws. This compression (pre-load) maintains contact between the faces and allows the PSS to compensate for the thrust from the propeller. The carbon flange is bored larger than the shaft diameter allowing it to "float" around the shaft and thus compensate for most misalignment and vibration problems. The stainless steel collar is sealed to the shaft by two o-rings that are recessed into the bore of the collar. These o-rings rotate with the shaft and stainless steel rotor and do not experience wear during operation. **As with any rubber hose below waterline, the PSS bellows must be inspected on a regular basis for any sign of wear, aging or chemical deterioration. PYI suggests as preventative maintenance that the PSS bellow be replaced in six year intervals. During bellows replacement it is recommended the o-rings & set screws in the stainless steel rotor also be replaced." Bellows may need to be more frequently inspected in an environment where non-sealed batteries emit sulfuric acid. Sulfuric acid vapor will accelerate rubber deterioration, as will an ozonater. The Maintenance Kit includes the items you need to properly maintain your PSS Shaft Seal. Included in the kit is one (1) PSS bellow, two (2) O-rings, five (5) set screws, four (4) new hose clamps and an allen key.

3/8" compression fittings which utilize a 9/16"-24 fine thread. NPT fittings are not to be used in a -3 helm and/or cylinder.

3/8" compression fittings which utilize a 9/16"-24 fine thread. NPT fittings are not to be used in a -3 helm and/or cylinder.

Flat Surface Mount w/1" Ball, including M6 X 30 SS HEX Head Bolt, f/Raymarine Dragonfly-4/5 & WiFish Devices The RAM-B-202-379-M616U consists of a 2.5" diameter round base with the universal AMPS hole pattern, STANDARD size double socket arm and 1" diameter ball, containing a M6 x 30 SS HEX head bolt. The mount is designed with a RAM 1" diameter patented rubber ball and socket system that has adjustment points at both ends of the double socket arm; this allowing for almost infinite adjustment and perfect viewing angles. The RAM-B-202-379-M616 reduces the mounting footprint, compared to old dragonfly units that contain a large neck. This mount allows for a seamless marriage of RAM components into your Raymarine system, opening up the ball and socket system and all of our mounting options to you. Material: High Strength Composite & Powder Coated Marine Grade Aluminum Ball Size: 1" Rubber Ball "B" Size Note: The "U" in the part number reflects product packaged in poly bag. Raymarine device not included with purchase.

Suction Cup Mount w/1" Ball, including M6 X 30 SS HEX Head Bolt, f/Raymarine Dragonfly-4/5 & WiFish Devices The RAM-B-224-1-379-M616U consists of a 3.3" diameter suction cup twist lock base, STANDARD length double socket arm and 1" diameter ball, containing a M6 x 30 SS HEX head bolt. The mount is designed with a RAM 1" diameter patented rubber ball and socket system that has adjustment points at both ends of the double socket arm; this allowing for almost infinite adjustment and perfect viewing angles. The suction cup, twist lock base is designed to have a strong hold on glass and non-porous plastic surfaces. The RAM-B-224-1-379-M616U reduces the mounting footprint, compared to old dragonfly units that contain a large neck. This mount allows for a seamless marriage of RAM components into your Raymarine system, opening up the ball and socket system and all of our mounting options to you. Material: High Strength Composite & Powder Coated Marine Grade Aluminum Ball Size: 1" Rubber Ball "B" Size Note: The "U" in the part number reflects product packaged in poly bag. Raymarine device not included with purchase. 

Oberdorfer 7321 Pipe Nut 3/8 Npt  

Swivel Shackle - 5/16" Pin - 2-3/8"L x 21/32"W Features: Coined head pin 7.9mm(5/16") Diameter Pin Grade 316 Stainless Steel bodies and pins Stainless Steel ball bearing race

3/8" compression fittings which utilize a 9/16"-24 fine thread. NPT fittings are not to be used in a -3 helm and/or cylinder.

Long Dee Shackle - 3/8" Pin - 2-3/8"L x 23/32"W Features: High strength to weight ratio Grade 316 Stainless Steel bodies and pins Drilled Shackle pin for siezing wire

Yamada 643018 O'Ring 20.8 mm X 2.4 mm