Single Pole Brass Battery Switch with Faceplate 175 Amp Continuous 800 Amp Intermittent Marine-Grade UL-Listed master disconnect switches.  Features: 6-36 VDC 175 Amp Continuous 800 Amp Intermittent 2 Positions Off-On Positions Single-Pole Circuitry Brass Case Lever Actuator

Single Pole Brass Marine Battery Switch - 175 Amp - Continuous 800 Amp Intermittent Marine-Grade UL-Listed master disconnect switches. Features: Voltage: 6-36 Vdc Electrical Ratings*: 250A at 6Vdc, 125A at 12Vdc intermittent, 40A at 6V, 20A at 12V continuous* Number of Positions: 2 Positions: Off-On Circuitry: Single-Pole Case: Brass Contacts: Silver or Brass Actuator: Lever

Single Pole Brass Marine Battery Switch - 175 Amp - Continuous 1000 Amp Intermittent Marine-Grade UL-Listed master disconnect switches. Features: Voltage: 6-36 Vdc Electrical Ratings*: 250A at 6Vdc, 125A at 12Vdc intermittent, 40A at 6V, 20A at 12V continuous* Number of Positions: 2 Positions: Off-On Circuitry: Single-Pole Case: Brass Contacts: Silver or Brass Actuator: Lever

3 Position Brass Ignition Switch with Rubber Boot Marine Grade Ignition Switches in brass or plastic. Off-Ign-Ign/Start, spring return to Ign. Key removable at Off.

4 Position Brass Ignition Switch Marine Grade Ignition Switches in brass or plastic. Off-Ign-Ign/Start, spring return to Ign. Key removable at Off.

3 Position Brass Ignition Switch Marine Grade Ignition Switches in brass or plastic. Off-Ign-Ign/Start, spring return to Ign. Key removable at Off. 

2 Position Brass Ignition Switch Marine Grade Ignition Switches in brass or plastic. Off-Ign-Ign/Start, spring return to Ign. Key removable at Off.

Heavy Duty Push Button Switch w/Rubber Cap SPST Off-On 2 Screw - 35A Features: 35A at 12V, 20A at 24V, 10A at 36V DC Normally Off, push to On Two brass screw terminals Mounting stem; brass 5/8" -32 thread, 1 3/8: (34.9mm) long, fits panels up to 1" (25.4mm) thick Silver contacts With snap-on black rubber cap

Heavy Duty Push Button Switch w/Gasket Seal SPST Off-On 2 Screw - 10A Features: Normally Off, push to On Two brass screw terminals Mounting stem; brass 5/8" -32 thread, 1 3/8: (34.9mm) long, fits panels up to 1" (25.4mm) thick Silver contacts Gasket Seal

Dual Battery Switch w/Mounting Ring & Legs - Bulkhead Mount The Perko Dual Battery Selector Switch allows the addition of an extra battery for accessories. This switch provides the flexibility of selection between batteries or combined operation of both batteries in parallel for starting or charging. It can also serve as an emergency main disconnect switch in the event of an electrical problem. All models are make before break design and are ignition protected. Four switch positions: Both "Off", Both "On", Battery 1 "On"/Battery 2 "Off", Battery 1 "Off"/Battery 2 "On" Materials & Finish Red polycarbonate polymer body Black polymer actuator key Nickel plated terminals Features For two or more batteries Unique oval shape mounts in a round hole Removable actuator key Technical Information Rating: 140 Amps Continuous, 200 Amps 5 Min. Intermittent, 250 Amps 30 Second Start For use with alternators and generators 6-50 V.D.C. Marine Electrical Systems Ignition Protected Face Dimensions: 3-7/8" x 3-1/4"

Remote Operated Battery Switch w/Optical Sensor 500A 12/24V The MD range of battery switches allow you to install the battery switch very close to the battery, to remotely manage the increased electrical loads found on today's boats. This reduces cable lengths and sizes, providing significant savings in expense and weight of copper battery cable. They are ideal for remote isolation of bow and stern thrusters. The 720-MDO has been enhanced to offer easy standard installation, or advanced options capable of switching different voltage circuits from the main supply (for example: a 48 volt bow thruster with a 24 volt house supply). The optical sensor uses the same easy connection for standard installation and gives you the ability to control different voltage circuits such as 36 or 48 volts. It can be used to switch positive or negative lines and the main contacts can be isolated from the control circuit allowing operation via another battery source. This optical sensor also has low stand-by current draw (<5mA). Remote operation Battery switch can be mounted alongside battery, reducing cable lengths and cable sizes. (Large cost and weight saving in copper cables) Reduced installation labor due to shorter battery cable runs Manual override option to meet CE/ABYC requirements LED status identification for remote control switch Same capacities/specifications and mounting options as standard BEP battery switches Uses interchangeable labeling system (Item # 713 or 715) Specifications: LxWxH: 4" x 4" x 4.33" Rating (A DC) Cont: 500 Rating (A DC) Inter: 700 Rating (A DC) Crank: 2500 Voltage (V DC): 9.5-32 Function: On/Off Stud Size: 2x (1/2"/12mm) WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

ML-RBS Remote Battery Switch with Manual Control Auto-Release - 12V Manual override knob provides an added level of safety allowing control with or without power and offering LOCKED OFF capability for servicing LED output to remotely indicate switch state - requires optional LED 3/ 8"-16 tin-plated copper studs for maximum conductivity and corrosion resistance 7/ 8" (22mm) stud length accepts multiple cable terminals Label recesses for circuit identification Silver alloy contacts provide high reliability for switching live loads Auto Releasing ML-Series Remote Battery Switch with SPST Switching Provides 500A switching and features of current ML Remote Battery Switches, but can be controlled with SPST or SPDT switch for applications where a normally open relay is desired Specifications Control Circuit Connection:Tinned Wire Nominal Voltage:12V DC Coil Function: Auto releasing Mounting: #10 Amperage Operating Current:8mA when OFF/13mA when ON Amperage Operating Current when changing state: <7A (40 ms) Control Circuit Voltage: 10.1 to 16.5V DC Continuous Rating: 500A Intermittent Rating: 700A (5 min) Cranking Rating: 10 sec 2500A Cranking Rating: 1 min 1100A Minimum Operating Temperature: -10° C Maximum Operating Temperature: 50° C Cable Size to Meet Ratings: 2x (4/0) Live Current Switching: 300A @ 12V DC 10,000 Cycles Master Control Switch Capability: Yes Mechanical Endurance: 100,000 Cycles Switching Cycles: 100,000 Terminal Ring Diameter Clearance: 1.18" (29.97mm) Terminal Stud Length: 0.875" (22.23mm) Terminal Stud Size: 3/8-16 (M10) Terminal Stud Torque: 140 in-lb (15.82 Nm) Weight: 1.75lb (0.79 kg) WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Easy Fit Battery Switch - 275A Continuous The Easyfit Battery Switch was created for installations where switches need to be recessed through varying thicknesses of panels. It achieves this through an easily removable threaded ring that allows for panel thicknesses up to 3/4" (19 mm). This switch uses the same features as the 701 with the removable key 45 degree past the off position, labeled handle and a removable back cover covering exposed terminals to meet ABYC specifications. It can also be surface mounted offering a unique style compared to other switches available on the market. BEP Marine Battery Switch Test Procedures (UL 1107) Continuous (1 hour), intermittent (5 minutes) and Cranking (engine starting - 10 seconds). The test is to determine the maximum current the switch can handle for the stated time, without the rear terminals exceeding 100 deg C (212 deg F) above the ambient temperature. The continuous and intermittent ratings are tested at 110% of specified ratings. All BEP switches are tested Independently to this specification by a 3rd party laboratory. Features: Can easily be retro-fitted in place of most European post and lever type switches Molded in high temperature, fiber reinforced plastics Tin-plated copper studs and nuts Ignition-protected WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

4 Pole Plug & Socket Connector with Rubber Cap Normally used with a trailer where only limited functionality (taillights. brake lights) is needed. Ideal for boat trailers or RVs towing a car on a flatbed trailer. Features: Diecast metal housings Screw terminals accept up to 12 AWG wire. Replaceable interiors Brass split-pin contacts are aligned to assure proper contact and minimal voltage drop Spring-loaded socket doors (the plug locks securely into the opening) Wiring codes are identified on the insulator Two mounting holes on the flange are 17/64" (6.7 mm) in diameter. 2-15/16" (74.6 mm) in centers. Mount through a 1 3/8" (34.9 mm) diameter hole. With special housing that protects terminals from road splash Specifications: Housing: Plated steel Circuitry: 4 Input Terminals: Brass Contact Material: Screw

ML-RBS Remote Battery Switch with Manual Control Auto-Release - 24V Manual override knob provides an added level of safety allowing control with or without power and offering LOCKED OFF capability for servicing LED output to remotely indicate switch state - requires optional LED 3/ 8"-16 tin-plated copper studs for maximum conductivity and corrosion resistance 7/ 8" (22mm) stud length accepts multiple cable terminals Label recesses for circuit identification Silver alloy contacts provide high reliability for switching live loads Auto Releasing ML-Series Remote Battery Switch with SPST Switching Provides 500A switching and features of current ML Remote Battery Switches, but can be controlled with SPST or SPDT switch for applications where a normally open relay is desired Specifications Control Circuit Connection:Tinned Wire Nominal Voltage:24V DC Manual Control: Yes Coil Function: Auto releasing Mounting: #10 Amperage Operating Current:8mA when OFF/13mA when ON Amperage Operating Current when changing state: <4A (40 ms) Control Circuit Voltage: 20.2 to 32.9V DC Continuous Rating: 500A Intermittent Rating: 700A (5 min) Cranking Rating: 10 sec 2500A Cranking Rating: 1 min 1100A Minimum Operating Temperature: -10° C Maximum Operating Temperature: 50° C Cable Size to Meet Ratings: 2x (4/0) Live Current Switching: 300A @ 12V DC 10,000 Cycles Master Control Switch Capability: Yes Mechanical Endurance: 100,000 Cycles Switching Cycles: 100000 Terminal Ring Diameter Clearance: 1.18" (29.97mm) Terminal Stud Length: 0.875" (22.23mm) Terminal Stud Size: 3/8-16 (M10) Terminal Stud Torque: 140 in-lb (15.82 Nm) Weight: 1.75lb (0.79 kg) WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.