Hydraulic Ram Type 1 - 12V High power, efficient drive units for maximum power with minimum consumption Ram allows the Power Steer Mode on the Pilot to be used in case of manual steering failure Integrated hydraulic system: no external hoses, reservoirs, etc...

Groco Gpb-1-12V Gear Pump, Oil Chg 12V  Groco- Gear Pump Bronze 3.0GPM 50psi Max 12VDC 3/8”NPT Ports

Groco GPBR-1-12V Reversable Gear Pump for Oil Changes Groco Gear Pump Bronze 3.0GPM 50psi Max 24VDC Reversible 3/8”NPT Ports

Groco Wsg-1 12V Gear Pump Pressure System  Groco- Water Pressure System Gear Pump Bronze 3GPM 20-40psi 12VDC with 1 Gallon Pressure Tank   More Info: Uses Groco GPB-1 Pump

Hydraulic Ram to 12V High power, efficient drive units for maximum power with minimum consumption. Ram drives allow the Power Steer mode on the Pilot to be used in cases of manual steering failure Fully Integrated (T0, T1 and T2 units) hydraulic system, no external hoses, reservoirs etc. Always remember to use the fully laden displacement of your boat when selecting a pilot. Typically a yacht fully provisioned with the water and fuel tanks full can be as much as 20% above the designed displacement. If your boat falls between two pilot types, choose the larger pilot type - an under rated pilot may not be able to perform adequately when you need it most. If in doubt, please check with an authorized B & G Dealer. If you are using a Ram, Rotary drive or existing drive unit from another manufacturer, these will, in most cases, be compatible with B & G units. Features: Max Boat Size: 19,000 lbs (9000 kg) Stroke: 7.87 in (200 mm) Hard Over Time: 12 sec Tiller Arm: 6.89 in (175 mm) Thrust: 771.6 lbs (350 mm) Rudder Torque: 136.6 lbs (62 kg) Required Computer: AC12, NAC-2 *Typical average cruising consumption

Hydraulic Ram T2 - 12V B&G's 12V Hydraulic T2 Autopilot Ram

Rotary Drive Type 1 - 12V The rotary drive is designed for power and sailboat systems that can be driven from the helm position through a chain and sprocket (e.g. cable and rod steering system). The outstanding design of the Raymarine rotary drive unit provides smooth, powerful autopilot controlled steering with quiet operation. Optional drive sprockets and modification to the steering chain may be required. Features: Rotary Drive Type 1 12V Specifications: Maximum Boat Displacement: 11,000 kg Peak Output Torque: 20 nm Maximum Shaft Speed: 33 rpm Recommended Hard-Over Time (no load): 10 seconds Power Consumption: 24-48w Corepack Used: ACU-200

Autopilot Pump Type 1 Adjustable Reversing 12V Up To 15 CI Cylinder TWICE THE POWER The unique Octopus piston pump delivers over twice the hydraulic output per watt of input than a standard hydraulic gear pump. HALF THE POWER CONSUMPTION Gear pumps leak oil between the gears, while a piston (such as used in car engines) does not.  This means the piston pump will place the cylinder ram exactly where it is required, positioning the rudder accurately.  This gives far sharper steering, reducingunnecessary course corrections meaning battery consumption on Octopus pumps is up to half that of other pumps. PINPOINT ACCURACY Leading autopilot manufacturers choose Octopus pumps for their non RFB pilot systems which do not have a Rudder Feedback unit. Previously, slop in the system caused by gear leakage meant that a Rudder Feedback unit was necessary to tell the pilot the exact rudder position. As Octopus pumps will always bring the ram back to the required position the Rudder Feedback unit is not required, which also greatly simplifies installation. SAVE ON INSTALLATION COSTS A professional installation should always have a method of isolating the pump from the steering system - Octopus pumps feature inbuilt shut off valves in the pump manifold. ADJUSTABLE FLOW RATE A pump that does not have variable flow (unless dedicated to a range of cylinders such as our fixed 0.8L pump) will be operating too fast or too slow in 90% of cases.  Autopilot manufacturers get around this problem by adjusting the output to the pump to compensate, which either forces the pump to operate for longer periods of time which increases power consumption and wear on the parts, or it will operate at high pressure for short periods of time - also putting unnecessary strain and wear on the system. Octopus Variable Flow Reversing Pumps precisely control the speed of the ram, reducing unnecessary battery consumption, pressure, strain and wear on the hydraulic system. Getting the best steering performance for the boat. The flow rate of the pump can be set to get the best hard over time (cylinder ram speed) for the particular boat.  Features: Reliable - Piston pump technology with only three moving parts Twice the Power - Delivers over twice the hydraulic output per watt of input Half the Power Consumption - Accurate ram positioning means fewer course corrections Adjustable Flow Rate - Configure performance to suit your vessel Easy Servicing - Shut off valves allow removal without draining steering system

Rotary Drive Type 2 - 12V The rotary drive is designed for power and sailboat systems that can be driven from the helm position through a chain and sprocket (e.g. cable and rod steering system). The outstanding design of the Raymarine rotary drive unit provides smooth, powerful autopilot controlled steering with quiet operation. Optional drive sprockets and modification to the steering chain may be required. Features: Rotary Drive Type 2 12V Specifications: Maximum Boat Displacement: 20,000 kg Peak Output Torque: 34 nm Maximum Shaft Speed: 33 rpm Recommended Hard-Over Time (no load): 10 seconds Power Consumption: 60-84w Corepack Used: ACU-400

Type 1 Pump 12volt Reversing hydraulic pump for use with steering systems equipped with 4.914 cubic inch (80cc 230cc) hydraulic steering rams. The Type 1 hydraulic drive is compatible with both S1/S1G and S2/S2G corepacks. Use the table below to determine the Type 1 hydraulic drive's capacity when used with each corepack Corepack Used S1 or S1G Ram Capacity 4.9in - 10.5in (80CC-172CC) Maximum Stall Pressure at 12V 750psi (50bar) (no load) 67in/min (1000cc/min) Corepack Used S2 or S2G Ram Capacity 4.9in - 14in (80cc - 230cc) Maximum Stall Pressure at 12V 750psi (50bar) Peak Flow Rate (no load) 67in/min (1000CC/min)

Evolution EV-150 Hydraulic Autopilot System Pack The Evolution EV-150 Hydraulic Autopilot System Pack is a complete autopilot-in-a-box kit that is ready to install on many popular fishing and cruising powerboats with hydraulic steering. The system comes complete with our p70Rs autopilot controller, EV1 Sensor Core, ACU150 Actuator Control Unit, Type 1 Hydraulic Pump, and an Evolution autopilot cabling kit. Engineered for simplicity, Raymarine's award-winning Evolution autopilots eliminate the need for complicated set up and calibration. Thanks to the intelligent 9-axis EV sensor core, the autopilot automatically evolves and adapts to your vessel's steering characteristics without any user adjustments. The result is precise and confident course keeping, regardless of vessel speed or sea conditions. The Evolution EV-150 system also employs Raymarine's patented Hydro-Balance™ technology which delivers superior autopilot performance for hydraulically steered boats, particularly those with outboard motors and rudder-reference less systems. Hydro-Balance automatically compensates for hydraulic system elasticity, steering system asymmetry, and torque steer to keep your boat on-course at trolling speed, cruising speed, and all-out running. Anglers will also love the Evolution Autopilot's built-in trolling patterns. Let the autopilot work the boat while you prep bait, set your lines and adjust your spread. The system is also equipped with Raymarine latest Evolution TrackIQ™ algorithms which deliver tighter track-keeping and faster track acquisition. It also uses information on vessel pitch, roll, yaw and heave to stabilize GPS navigation data like course over ground, speed over ground and cross track error for the best possible tracking to waypoints and routes. The Raymarine EV-150 Hydraulic Autopilot System Pack is the ideal autopilot for small to medium sized hydraulically steered vessels with a steering ram capacity between 4.9 cu. in. (80cc) and 14.0 cu in. (230cc). The system is for 12-volt DC electrical systems only. Includes E70329 p70Rs Control Head E70096 EV-1 Sensor Core R70160 Evolution Cable Kit E70430 ACU-150 Actuator Control Unit M81120 Type 1 12v Hydraulic Pump

RAM-ROD 1.5" Diameter Ball & Hardware f/RAM 5 Spot Mounting Base Color: Black Material: High Strength Composite

RAM Composite 1" Ball Mount with 6.25" X 2" Rectangular Plate & Track Ball™ Base The RAP-B-111B-354-TRA1U consists of a Track Ball™ base, composite double socket arm and 6.25" x 2" rectangle plate. The 6.25" x 2" rectangle plate contains different combinations of pre-drilled holes which will match up to many electronic devices and mounts, including Marine GPS, CB Radios, Ham Radios, Gimbal Brackets and more. The Track Ball™ base can connect to virtually any track system including the RAM Tough-Track™ Overall Height: 6" Ball Size: 1" Rubber "B" Ball Size Material: High Strength Composite Base Marine Grade Aluminum Plate Note: Part number reflects product packaged in a poly bag.

RAM Mount 1" Diameter Ball Mount w/Long Double Socket Arm & 2/2.5" Round Bases - AMPS Hole Pattern (7-5/16" Length) The RAM-B-101U-C consists of a long double socket arm and two 2.5" diameter round bases that contain the universal AMPS hole pattern. The mount is designed with a 1" diameter patented rubber ball and socket system that has adjustment points at both ends of the double socket arm; this allowing for almost infinite adjustment and perfect viewing angles. The hole pattern found on the round base adapter will connect to many RAM cradles, including all iPad cradles. The included RAM's patented design dampens shock and vibration, helping to extend the life of your device. Overall Height: 7.3125" Material: Powder Coated Marine Grade Aluminum Ball Size: 1" Rubber "B" Ball Size Note: The "U" in the part number reflects product packaged in poly bag.

RAM Motorcycle 1" Ball Adapter for Brake/Clutch Reservoir Base This ball connects to the open hole on the side of the RAM-B-309-1U (single 1" ball) and is included with the purchase of the RAM-B-309-2U (double 1" ball). Material: Powder Coated Marine Grade Aluminum Ball Size: 1" Rubber Ball "B" Size Note: The "U" in the part number reflects product packaged in poly bag.