Siphon-Mate Siphon Pump Specialty Transfer Pump Safety experts caution against the unsafe practice of siphoning petroleum by mouth, warning specially, that it can result in loss of life. Beckson's answer is the patented Siphon-Mate pump; a combination displacement lift pump and siphon pump with valves suitable for transferring fuel. Pump half strokes to start flow. Once flow begins, fully extending the handle will allow siphoning provided that the source is higher in elevation than the receptacle. Supplied with clear tubing to allow versatile application. Cut tubing for desired length of intake and discharge hose. When finished siphoning or pumping flammable liquids, be sure to drain siphon pump of liquid before storing. This pump not intended for transfer of liquid over 120 degrees F (49 degrees C) nor solvents that will attack PVC. Features Use for diesel, oil, water Length: 11-1/2" (28.4cm) Diameter: 1-1/4" (32mm) Lifts: 4 oz (.12 L) per stroke WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Mate USA M164-095-15 12/24V Reversible Diesel/Oil Transfer Pump with Flow Regulation UP8-RE Volt: 12V & 24V Fuse: 4A/2A Gpm: 2.6 Ports: 3/8" NPT Psi: 51 Diesel: Yes Oil: Yes   Heavy duty Electronic Gear pump with Integrated Smart Keypad to reverse the flow direction and to manually fine tune the flow rate. The flow rate is also automatically adjusted according to the viscosity of the fluid to avoid cavitation. Best for oil and diesel transferring. Compact and Easy to operate and carry.

Thirsty-Mate Hand Pump with 20" Hose The Beckson THIRSTY-MATE hand pump is manufactured in the U.S.A. of the finest materials available. It is self-priming and very easy to clean. This hand pump will not rust or corrode or mar your boat. If your THIRSTY-MATE hand pump becomes clogged, simply remove the foot valve assembly and clean out the inside. Spare parts such as replacement foot valve assemblies and hoses are readily available. Features: Angled top sleeve Contoured red tee handle Non-conductive material Self-priming plunger valve Special polyvinyl grey body and shaft Removable foot valve for cleaning Self-priming Solvent welded construction Will withstand temperature to 120 degrees F (49 degrees C) Length: 18" Diameter: 1-1/4" Strokes/Gal: 10 Capacity: 6GM Hose Length: 20" WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Thirsty-Mate Hand Pump The Beckson THIRSTY-MATE hand pump is manufactured in the U.S.A. of the finest materials available. It is self-priming and very easy to clean. This hand pump will not rust or corrode or mar your boat. If your THIRSTY-MATE hand pump becomes clogged, simply remove the foot valve assembly and clean out the inside. Spare parts such as replacement foot valve assemblies and hoses are readily available. Features: Angled top sleeve Contoured red tee handle Non-conductive material Self-priming plunger valve Special polyvinyl grey body and shaft Removable foot valve for cleaning Self-priming Solvent welded construction Will withstand temperature to 120 degrees F (49 degrees C) Length: 36" Diameter: 1-3/4" Strokes/Gal: 4 Capacity: 13GPM Hose Length: 36" WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Thirsty-Mate Hand Pump The Beckson THIRSTY-MATE hand pump is manufactured in the U.S.A. of the finest materials available. It is self-priming and very easy to clean. This hand pump will not rust or corrode or mar your boat. If your THIRSTY-MATE hand pump becomes clogged, simply remove the foot valve assembly and clean out the inside. Spare parts such as replacement foot valve assemblies and hoses are readily available. Features: Angled top sleeve Contoured red tee handle Non-conductive material Self-priming plunger valve Special polyvinyl grey body and shaft Removable foot valve for cleaning Self-priming Solvent welded construction Will withstand temperature to 120 degrees F (49 degrees C) Length: 36" Diameter: 1-3/4" Strokes/Gal: 4 Capacity: 13GPM Hose Length: 72" WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Thirsty-Mate Hand Pump The Beckson THIRSTY-MATE hand pump is manufactured in the U.S.A. of the finest materials available. It is self-priming and very easy to clean. This hand pump will not rust or corrode or mar your boat. If your THIRSTY-MATE hand pump becomes clogged, simply remove the foot valve assembly and clean out the inside. Spare parts such as replacement foot valve assemblies and hoses are readily available. Features: Angled top sleeve Contoured red tee handle Non-conductive material Self-priming plunger valve Special polyvinyl grey body and shaft Removable foot valve for cleaning Self-priming Solvent welded construction Will withstand temperature to 120 degrees F (49 degrees C) Length: 36" Diameter: 1-3/4" Strokes/Gal: 4 Capacity: 13GPM Hose Length: 108" WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Thirsty-Mate Hand Pump The Beckson THIRSTY-MATE hand pump is manufactured in the U.S.A. of the finest materials available. It is self-priming and very easy to clean. This hand pump will not rust or corrode or mar your boat. If your THIRSTY-MATE hand pump becomes clogged, simply remove the foot valve assembly and clean out the inside. Spare parts such as replacement foot valve assemblies and hoses are readily available. Features: Angled top sleeve Contoured red tee handle Non-conductive material Self-priming plunger valve Special polyvinyl grey body and shaft Removable foot valve for cleaning Self-priming Solvent welded construction Will withstand temperature to 120 degrees F (49 degrees C) Length: 24" Diameter: 1-1/2" Strokes/Gal: 7 Capacity: 8GPM Hose Length: 24" WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Thirsty-Mate Hand Pump The Beckson THIRSTY-MATE hand pump is manufactured in the U.S.A. of the finest materials available. It is self-priming and very easy to clean. This hand pump will not rust or corrode or mar your boat. If your THIRSTY-MATE hand pump becomes clogged, simply remove the foot valve assembly and clean out the inside. Spare parts such as replacement foot valve assemblies and hoses are readily available. Features: Angled top sleeve Contoured red tee handle Non-conductive material Self-priming plunger valve Special polyvinyl grey body and shaft Removable foot valve for cleaning Self-priming Solvent welded construction Will withstand temperature to 120 degrees F (49 degrees C) Length: 30" Diameter: 1-1/2" Strokes/Gal: 6 Capacity: 10GPM Hose Length: 32" WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Impeller Kit F3 Nitrile A worn or damaged impeller can cause system failure or engine breakdown. SPX's Johnson Pump brand impellers are developed and manufactured for maximum flow and long life. With a genuine spare impeller you can also be sure that you are getting the quality required by engine manufacturers and professionals. Features:  Made for F3B Pump Material: Nitrile (oil resistant) In The Product Box: Impeller Glycerine lubricate O-rings, gasket, and cover Dimensions: Outer Diameter: 1.78" Inner Diameter: 0.31"/Flat Width: 0.50" *F3B oil pump with reversible switch sold separately 

Jabsco 18777-0001-B Neoprene Impeller Kit Neoprene impeller material for water pumping applications Spline drive hub 10 impeller blades 2 1/4 in. diameter x 2 in. width x 5/8 in. shaft Used in Jabsco 50410, 22110, and 23800 model crank shaft driven pumps Impeller profile HH in Jabsco impeller identification charts Replaces Jabsco 22120-0001, 18777-0001, 18777-01 Replaces Volvo Penta 876120 Replaces Marine Power 527272

Micropump DG-F61.G1S2P5.J.B I Drive Motor J Mount Micropump Brushless DC I-Drive

Micropump GC-M25.PVS.F Pump Head F Mount Micropump 81378 GC-M25.PVS.F Mag-Drive Gear Pump Head, Requires A-Mount compatible Drive. 81378 constructed of Base Material 316SS, Gear Material PPS (carbon fiber/ptfe) and Shaft Material 316SS. Pump Series: GC Series Ports/Fittings: 3/8-18 (F) NPT Side Port Min Speed (RPM): 500 Max Speed (RPM): 4000 Max Pressure (psi): 1500 Min Temperature (°C): -29 Max Temperature (°C): 176.666666666667 Max Diff. Pressure (psi): 75 Displacement (ml/rev): 1.82 Design: Standard Design Gear Set: 0.750/2/20 (1.82 ml/rev) Gear Material: PPS (carbon fiber/ptfe) Static Seals: Viton® Base Materials: 316SS Drive Mount: MP Housing (220 Style) Bypass: No Driven: Ferrite Driving Magnet: Not Included High System Pressure: No Bushings: PPS Shafts: 316SS Gear Trim: None Model: GC-M25.PVS.F

Mate USA M162-004-13 Water Pump with Nitrile flexible impeller UP1-J GPM: 7.4 Ports: 3/4" Barb Volt: 24V Fuse 4 amp Gpm: 7.4 Psi: 15 Fresh water: Yes Salt water: Yes Greywater: Yes   This Mate USA 7.4 GPM Self-priming electric pump with flexible rubber impeller. Is fitted with water proof cable guide and internal brush holder with EMI filter. ISO 8846 and ISO 8849. Ideal for bilge and waste water on any type of boat.   Note: image is showing a 12volt pump, This pumps is 24v.

Mate USA M162-001-1C Water Pump 220V 50HZ PUMP UP1/AC 7.9 GPM Bilge & Grey Water Pump Volt: 220V Fuse 3.3 amp Ports 1" Barb Gpm: 7.9 Psi: 14.5 Fresh water: Yes Salt water: Yes   This Mate USA 7.9 GPM Self-priming electric pump with flexible nitrile impeller. Nickel-plated brass body, shaft in stainless steel AISI 303. Electric motor 0.55 kW. Ideal for transfer of fresh or salt water.

Micropump GC-M35.PVS.F Pump Head F Mount Micropump 81379 GC-M35.PVS.F Mag-Drive Gear Pump Head, Requires A-Mount compatible Drive. 81379 constructed of Base Material 316SS, Gear Material PPS (carbon fiber/ptfe) and Shaft Material 316SS.