164WR-1 Crows Foot Transducer Wrench Transducer wrenches are available for all bronze low profile transducers. They are used to facilitate holding of the transducer and tightening of the hull nut. Wrenches are constructed of 3/16" thick mild steel. They can easily be bent or modified to accommodate challenging installation locations. For use with: B164 SS164 B175C SS164

117WR-1 Crows Foot Transducer Wrench Transducer wrenches are available for all bronze low profile transducers. They are used to facilitate holding of the transducer and tightening of the hull nut. Wrenches are constructed of 3/16" thick mild steel. They can easily be bent or modified to accommodate challenging installation locations. For use with: B117 B150 B744V B744VL B765C SS555

75WR-1 Crows Foot Transducer Wrench Transducer wrenches are available for all bronze low profile transducers. They are used to facilitate holding of the transducer and tightening of the hull nut. Wrenches are constructed of 3/16" thick mild steel. They can easily be bent or modified to accommodate challenging installation locations. For use with: B75 SS75

60WR-1 Crows Foot Transducer Wrench Transducer wrenches are available for all bronze low profile transducers. They are used to facilitate holding of the transducer and tightening of the hull nut. Wrenches are constructed of 3/16" thick mild steel. They can easily be bent or modified to accommodate challenging installation locations. For use with: SS60 B60

164WR-3 Double Handle Transducer Wrench Transducer wrenches are available for all bronze low profile transducers. They are used to facilitate holding of the transducer and tightening of the hull nut. Wrenches are constructed of 3/16" thick mild steel. They can easily be bent or modified to accommodate challenging installation locations. For use with: B164 SS164 B175C SS264

117WR-3 Double Handle Transducer Wrench Transducer wrenches are available for all bronze low profile transducers. They are used to facilitate holding of the transducer and tightening of the hull nut. Wrenches are constructed of 3/16" thick mild steel. They can easily be bent or modified to accommodate challenging installation locations. For use with: B117 B150 B744V B744VL B765C SS555

60WR-3 Double Handle Transducer Wrench Transducer wrenches are available for all bronze low profile transducers. They are used to facilitate holding of the transducer and tightening of the hull nut. Wrenches are constructed of 3/16" thick mild steel. They can easily be bent or modified to accommodate challenging installation locations. For use with: B60 SS60

75WR-3 Double Handle Transducer Wrench Transducer wrenches are available for all bronze low profile transducers. They are used to facilitate holding of the transducer and tightening of the hull nut. Wrenches are constructed of 3/16" thick mild steel. They can easily be bent or modified to accommodate challenging installation locations. For use with: B75 SS75

Tuthill 1LEV-C-A-88462 Pump 3.2Gpm 1/2Hp 1725Rpm 1P

Tuthill 2LE-A-7 Pump 6.2Gpm 1/2"Ports Cast Iron Rotary Gear Pump Pump End Only L Series Pump Cast Iron Construction Tang Shaft Inlet Port is 1/2 inch NPT Discharge Port is 1/2 inch NPT Positive Displacement, Internal Rotary Gear Design Open Flow at 1800 RPM : 5.6 GPM at 1800 RPM Standard Discharge Pressure: up to 500 PSI Inlet Pressure: up to 280 PSI Maximum Differential Pressure: 300 PSI Temperature: up to 375 F Typical Viscosity Range: 40 to 1000 SSU

Airmar R111LH 2kW In-Hull Transducer, CHIRP Low (38-75kHz)  & CHIRP High (130-210kHz) This in-hull transducer uses narrow beams at low/high frequencies to display depth and temperature data to your Garmin Marine Network via your sonar, such as the GSD 26. Designed to allow both traditional and Spread Spectrum scanning, this 2kW barewire, plastic transducer has a maximum depth of 8,000 ft; an operating frequency of 38 to 75 kHz and 130 to 210 kHz; and a beamwidth of 10x19 degrees. The in-hull mounts on a 0-25° deadrise angle; the pocket mount is installation dependent. Transducer kit comes with installation instructions. Follow the instructions carefully to avoid damaging your boat. *In-hull not recommended for cored-hull vessels WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Jabsco HP340-1890 Hyline Plus 1" No Feet

Jabsco HP340-B005 Hyline Plus 1" No Feet

Bosworth 74-1 Foot/Check Valve 1"   Bosworth- Foot Valve / Check Valve Sea-Lect Gray Delrin, Buna Flapper Valve, 1" Smooth Hose Ports

Bosworth 74  1 1/4" Foot/Check Valve   Bosworth- Foot Valve / Check Valve Sea-Lect Gray Delrin, Buna Flapper Valve, 1 1/4” Smooth Hose Ports