|
V60-B VHF Marine Radio with DSC & AIS (Receive & Transmit)
See and Be Seen with Integrated AIS
The V60-B includes a Class B AIS transmitter and receiver, which not only receives AIS targets but also transmits your yacht’s position to nearby AIS-equipped vessels. This helps other mariners to spot your boat through any conditions, day or night. A built-in AIS receiver monitors the position of other AIS-equipped vessels, helping you to proactively avoid collisions in crowded harbors and waterways. AIS information can be viewed on the radio’s built-in screen or overlaid on your chart or radar screen through a compatible chartplotter.
Removable Fist Mic
The V60-B’s removable fist mic can be connected to the front or rear of the radio, and optional extension cables allow the mic and radio to be mounted separately. This offers a simple and cost-effective solution for any mounting location, with no cable clutter. For instance, the V60-B can be mounted overhead, with no hanging cables, while the mic is connected to an extension socket on the dash below.
Expandable with Wireless Handsets
Add an optional H60 wireless handset to take your radio anywhere on board. Each handset duplicates your radio’s display and controls, enabling remote access to all key functions. Up to two handsets can be connected to a single V60-B, and with multiple handsets connected your radio doubles as an on-board intercom.
Man Overboard (MOB) function
Hold down the NAV/MOB button to drop a waypoint on your current location and the V60-B will enter MOB mode to show you how far away you are and where you need to steer to get back to the position of the MOB event. The MOB waypoint is also transmitted over NMEA 2000 to the rest of your network.
Track up to 5 Buddies!
The Track Buddy feature will automatically request the position of another VHF radio at set intervals. Simply enter the MMSI of the VHF into your contact list and start tracking! You will be able to see their position in any compatible chartplotter.
Features:
Class D DSC-approved VHF radio
See and be seen with an integrated Class B AIS transceiver
Integrated GPS receiver
Removable fist mic supports front or rear connection
Connect up to two wireless handsets
Add an optional loudhailer or external speaker
NMEA0183® and NMEA 2000® connectivity
Track up to 5 vessels with the ‘Track Buddy’ feature
Use Navigation Mode to display speed and course
Includes Man Overboard (MOB) function
In the Box:
V60 VHF Radio
000-14922-001 Fist Mic V60
000-14917-001 Mounting Bracket and Knobs
000-14915-001 Flush Mounting Kit
000-14913-001 Suncover
000-14919-001 Mic Clip
|
1438.80 |
|
|
V60-B VHF Marine Radio with DSC, AIS (Receive & Transmit) & GPS-500 GPS Antenna
See and Be Seen with Integrated AIS
The V60-B includes a Class B AIS transmitter and receiver, which not only receives AIS targets but also transmits your yacht’s position to nearby AIS-equipped vessels. This helps other mariners to spot your boat through any conditions, day or night. A built-in AIS receiver monitors the position of other AIS-equipped vessels, helping you to proactively avoid collisions in crowded harbors and waterways. AIS information can be viewed on the radio’s built-in screen or overlaid on your chart or radar screen through a compatible chartplotter.
Removable Fist Mic
The V60-B’s removable fist mic can be connected to the front or rear of the radio, and optional extension cables allow the mic and radio to be mounted separately. This offers a simple and cost-effective solution for any mounting location, with no cable clutter. For instance, the V60-B can be mounted overhead, with no hanging cables, while the mic is connected to an extension socket on the dash below.
Expandable with Wireless Handsets
Add an optional H60 wireless handset to take your radio anywhere on board. Each handset duplicates your radio’s display and controls, enabling remote access to all key functions. Up to two handsets can be connected to a single V60-B, and with multiple handsets connected your radio doubles as an on-board intercom.
Man Overboard (MOB) function
Hold down the NAV/MOB button to drop a waypoint on your current location and the V60-B will enter MOB mode to show you how far away you are and where you need to steer to get back to the position of the MOB event. The MOB waypoint is also transmitted over NMEA 2000 to the rest of your network.
Track up to 5 Buddies!
The Track Buddy feature will automatically request the position of another VHF radio at set intervals. Simply enter the MMSI of the VHF into your contact list and start tracking! You will be able to see their position in any compatible chartplotter.
Features:
Class D DSC-approved VHF radio
See and be seen with an integrated Class B AIS transceiver
Integrated GPS receiver
Removable fist mic supports front or rear connection
Connect up to two wireless handsets
Add an optional loudhailer or external speaker
NMEA 0183® and NMEA 2000® connectivity
Track up to 5 vessels with the ‘Track Buddy’ feature
Use Navigation Mode to display speed and course
Includes Man Overboard (MOB) function
In the Box:
V60 VHF Radio
000-14922-001 Fist Mic V60
000-14917-001 Mounting Bracket and Knobs
000-14915-001 Flush Mounting Kit
000-14913-001 Suncover
000-14919-001 Mic Clip
000-13613-001 GPS-500 GPS Antenna
|
1558.80 |
|
|
BEP Marine
BEP engineers and manufactures a range of high quality electrical solutions designed for the harsh Marine and RV environments. Every product it makes meets exacting performance specifications and is designed to withstand conditions both at sea, and on land. The engineers and product managers at BEP continue to develop the next generation of power management products.
|
|
|
Easy Fit Battery Switch - 275A Continuous
The Easyfit Battery Switch was created for installations where switches need to be recessed through varying thicknesses of panels. It achieves this through an easily removable threaded ring that allows for panel thicknesses up to 3/4" (19 mm). This switch uses the same features as the 701 with the removable key 45 degree past the off position, labeled handle and a removable back cover covering exposed terminals to meet ABYC specifications. It can also be surface mounted offering a unique style compared to other switches available on the market. BEP Marine Battery Switch Test Procedures (UL 1107) Continuous (1 hour), intermittent (5 minutes) and Cranking (engine starting - 10 seconds). The test is to determine the maximum current the switch can handle for the stated time, without the rear terminals exceeding 100 deg C (212 deg F) above the ambient temperature. The continuous and intermittent ratings are tested at 110% of specified ratings. All BEP switches are tested Independently to this specification by a 3rd party laboratory.
Features:
Can easily be retro-fitted in place of most European post and lever type switches
Molded in high temperature, fiber reinforced plastics
Tin-plated copper studs and nuts
Ignition-protected
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
31.92 |
|
|
Contour Matrix Gas Detector with Control
The Contour Matrix Gas Detectors are the product of continuing research and development which BEP Marine Ltd devotes to their product range. The BEP Detectors use microprocessor control to ensure correct sensor sensitivity. The Detectors have the capability to control two sensors that detect both LPG and Petrol, with visual and audible alarms. There is a test switch to check the operation of sensors with indicators for fault detection. 600-GDL Gas Detector has the same features as the 600-GD, with the additional ability to switch a valve on and off. The 600-GDL has a "pulse and hold" feature which allows the solenoid valve to be opened, using full power, and then reducing power to hold the valve in the open position. This reduces power consumption and heat generated whilst the valve is in the on position.
Features:
Operating Voltage 10 to 32 Volts DC
Self-testing capability
Microprocessor control
Provision for external alarm
Automatic shut-off solenoid control with pulse and hold circuit for low power draw (600-GDL only)
Provision for bilge blower
Dual sensor capability
For remote alarm operation use part no. 54-27C4
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
286.63 |
|
|
DC Color Systems Monitor (DCSM) - No Shunt
DC Systems Monitor (DCSM) Designed and manufactured by BEP, these state of the art full colour monitors are made to meet the systems monitoring requirements of today's modern vessel and recreational vehicle. Complex and DC electrical installations on board are becoming more common place. Additionally the increase in tank monitoring requirements for fuel, fresh, grey and black water, accurate monitoring of these systems is essential. The DCSM display features clear, extra large type face. This allows for more detailed on-screen information and increased clarity. The screen has back lighting for easy night time viewing.
Features:
8 Generic, user configurable inputs
Programmable high/low audio /visual alarms for volts, amps and tank levels
Backlit keypad and dimmable screen
Can be panel or surface mounted
2.8" Colour QVGA LCD
Input voltage 8-32VDC
Dimensions: Width 90mm x Height 100mm
Backlit keypad
Monitors charge/discharge amps for two banks
Monitors capacity remaining in A/h and %
Monitors battery condition
Monitors tank fluid level
Monitors circuit status
|
391.00 |
|
|
Mini Battery Selector Switch
The 701S is the most compact selector switch available on the market. While BEP recommends isolated battery systems as outlined with our distribution clusters, the 701S provides a simple economical way of separating two batteries. BEP Marine Battery Switch Test Procedures (UL 1107) Continuous (1 hour), intermittent (5 minutes) and Cranking (engine starting - 10 seconds). The test is to determine the maximum current the switch can handle for the stated time, without the rear terminals exceeding 100 deg C (212 deg F) above the ambient temperature. The continuous and intermittent ratings are tested at 110% of specified ratings. All BEP switches are tested Independently to this specification by a 3rd party laboratory.
Housed in the same dimensions as the 701, and includes the same removable side plates and back cover
Please note selector switches will not separate electronics from harmful engine starting spikes
Tin-plated copper studs and nuts
Ignition-protected
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
35.83 |
|
|
Sprayway manufactures a complete line of industrial MRO, automotive, screen print and housekeeping products since 1947. Sprayway has been an innovative industry leader, and its Sprayway Glass Cleaner is recognized as "The World's Best." From marine detailing to industrial maintenance, whether it is a detailing wax or an industrial lubricant, Sprayway provides wide-ranging industries with the products they need.
The World's Best Glass Cleaner - Excellent for windows, mirrors, windshields and other glass surfaces!
For cleaning and polishing glass, mirrors, windshields and windows. This easy-to use, fast acting product uses a clinging foam to break up soils and hold them - even on vertical surfaces. There is no dripping, no running and no streaking. With an exclusive formulation using denatured alcohol and no ammonia, this product cleans thoroughly, dries quickly, requires no rinsing and leaves a pleasant, fresh aroma.
SHOP: https://www.clrmarine.com/462m4/manufacturers/s/sprayway.html
Specials Closeouts Remanufactured Rebates
|
|
|
Mini Contour Battery Disconnect Switch - 275A Continuous
This switch offers a number of unique features, the highlight being the Contour Locking System, allowing it to be a stand alone unit, or locked together with other switches. The control knob can be removed by switching to an counterclockwise 45 degree position. This control knob also features an interchangeable labeling system allowing a full range of applications (Item # 713 or 715). Three removable side plates provide access of up to 1/0 cables. The rear cover insulating the rear terminals against any short circuits. This ensures that the switch meets ABYC requirements. BEP Marine Battery Switch Test Procedures (UL 1107) Continuous (1 hour), intermittent (5 minutes) and Cranking (engine starting - 10 seconds). The test is to determine the maximum current the switch can handle for the stated time, without the rear terminals exceeding 100°C (212°F) above the ambient temperature. The continuous and intermittent ratings are tested at 110% of specified ratings. All BEP switches are tested Independently to this specification by a 3rd party laboratory.
Features:
Can be either surface or recess mounted by cutting a 2.1" (52 mm) hole
Available with house knob (OEM # 701B-HB) or with chassis knob (OEM # 701B-CH)
Tin-plated copper studs and nuts
Ignition-protected
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
27.49 |
|
|
Heavy-Duty Battery Selector Switch
The 721 Battery Selector Switch is our heavy duty selector switch. Housed in the same module as the 720, it includes the same removable plates and back cover. While BEP Marine recommends isolated battery systems as outlined with our distribution clusters, the 721 offers a simple economical way of separating two batteries. Please note selector switches will not separate electronics from harmful engine starting spikes.
Specifications:
DC Voltage: 48
Stud Size (Imperial): 3 x 3/8"
Stud Size (Metric): 2 x 10mm
Continuous Rating: 350
Intermittent Rating: 500
Cranking Rating: 1500
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
59.10 |
|
|
Circuit Breaker Panel - 4-Way
BEP Marine uses the highest quality materials in its range of Control Panels, from the marine grade aluminium base plates to the Airpax magnetic hydraulic circuit breakers.
Features
Marine Grade powder coated aluminium
Airpax circuit breaker
Stylish Contour Design fascia
Green LED backlit labels
Red LED indicates systems on
Panels meet ABYC standards
Specifications
Total Positions: 4 Loads
Circuit Breakers: 1X 5A, 2X 10A, 1X 15A
Nominal Voltage: 12V
Maximum Amperage: 80A
Dimensions: 4.5" X 5" X 2.5"
Neg Bus: 6 Way
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
136.90 |
|
|
DC Panel - 8-Way - Horizontal
BEP Marine uses the highest quality materials in its range of Control
Panels, from the marine grade aluminium base plates to the Airpax magnetic
hydraulic circuit breakers.
Features
Marine Grade powder coated aluminium
Airpax circuit breaker
Stylish Contour Design fascia
Green LED backlit labels
Red LED indicates systems on
Panels meet ABYC standards
Specifications
Total Positions: 8 Loads
Circuit Breakers: 2X 5A, 2X 10A, 3X 15A, 1X 20A
Nominal Voltage: 12V
Maximum Amperage: 160A
Dimensions: 4.5" X 9.75" X 2.5"
Neg Bus: 6 Way
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
240.71 |
|
|
DC Panel - 8-Way - Vertical
BEP Marine uses the highest quality materials in its range of Control
Panels, from the marine grade aluminium base plates to the Airpax magnetic
hydraulic circuit breakers.
Features
Marine Grade powder coated aluminium
Airpax circuit breaker
Stylish Contour Design fascia
Green LED backlit labels
Red LED indicates systems on
Panels meet ABYC standards
Specifications
Total Positions: 8 Loads
Circuit Breakers: 2X 5A, 2X 10A, 3X 15A, 1X 20A
Nominal Voltage: 12V
Maximum Amperage: 160A
Dimensions: 7.9" X 5" X 2.5"
Neg Bus: 6 Way
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
240.71 |
|
|
DC Panel - 12-Way - No Meter - Horizontal
BEP Marine uses the highest quality materials in its range of Control
Panels, from the marine grade aluminium base plates to the Airpax magnetic
hydraulic circuit breakers.
Features
Marine Grade powder coated aluminium
Airpax circuit breaker
Stylish Contour Design fascia
Green LED backlit labels
Red LED indicates systems on
Panels meet ABYC standards
Specifications
Total Positions: 12 Loads
Circuit Breakers: 3X 5A, 4X 10A, 4X 15A, 1X 25A
Nominal Voltage: 12V
Maximum Amperage: 100A
Dimensions: 4.5" X 13.9" X 2.5"
Neg Bus: 6 Way
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
373.86 |
|
|
DC Panel - 12-Way - No Meter - Vertical
BEP Marine uses the highest quality materials in its range of Control
Panels, from the marine grade aluminium base plates to the Airpax magnetic
hydraulic circuit breakers.
Features
Marine Grade powder coated aluminium
Airpax circuit breaker
Stylish Contour Design fascia
Green LED backlit labels
Red LED indicates systems on
Panels meet ABYC standards
Specifications
Total Positions: 12 Loads
Circuit Breakers: 3X 5A, 4X 10A, 4X 15A, 1X 25A
Nominal Voltage: 12V
Maximum Amperage: 160A
Dimensions: 11.25" X 5" X 2.5"
Neg Bus: 6 Way
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
373.86 |
|