Shakespeare Style 4720 Economy Rail Antenna Mount Shakespeare's Style 4720 Economy Rail Mount is designed for quick and easy installation on vertical or horizontal, straight or angled rails. Its simple design makes installation a snap. The vice section grips the rail, and the flat section supports the antenna. The flat section can also be bolted to a flat surface, instead of to the rail grip. Standard 1" - 14 thread Nylon adapters included for 7/8", 1", and 1-1/4" vertical or horizontal rails Stainless steel construction

WindTrak AV Antenna Mount Wind Vane WindTrak wind vanes continue to offer exceptional performance at the best value of any wind indicator worldwide. The secret is in the sapphire jewel suspension bearing, large fin-low inertia vane, and easy-to-read, fully adjustable tacking tab system. WindTrak AV installs onto most whip antennas, including Metz and Shakespeare brands, with a whip diameter less than 1/8" (3 mm). Combine two installations into one to reduce masthead clutter, weight, and windage aloft. Rides on low-friction Teflon® bearings. Complete with 15" (38 cm) vane, reflective tacking arms, hardware and instructions for easy installation. Antenna not included.

GPS / VHF Antenna Mount for Self Levelling Radar Mount Single mount for installing an additional GPS / VHF antenna above the radar. Features Attaches to top of radome cradle Fits all standard GPS / VHF antennas with 1? x 14 tpi thread attachment Materials Marine grade 316 stainless steel GPS / VHF Antenna Mount Kit 1 x GPS / VHF mount 2 x M6 x 8mm bolts 2 x M6 spring washers

The RAM antenna mount is designed to hold most VHF and similar antennas. The rubber ball and socket system securely mounts the antenna while allowing for almost infinite adjustment. Mount the antenna on a horizontal or vertical surface or anywhere in between. The ball base is made from a light weight marine grade aluminum with powder coat. The ball socket and male 1" -14 threaded post are made from high strength composites designed for prolonged outdoor use. The RAM antenna mount will work with any standard antenna that has a 1" -14 threaded interface. Color: Black Powder Coat Ball Size: 1.5 Inch Rubber Ball Material: Marine Grade Aluminum and Composites

Rail / Side Mount Lets you secure your downrigger to the rail of your boat. No cutting or drilling necessary. Just clamp this aluminum mount to the rail and position your downrigger on the base. It can also be used to mount a downrigger to the side of your boat when gunwales won't accommodate deck plates or bases. Should be attached at the "T" joint of the rail. WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Stainless Steel Stud Mount Flanged Hand Rail with Mounting Flange - 12"  These Stud Mounted Flanged Hand Rail features integral 5/16”-18 threaded studs and installs with two 5/16”-18 nuts (not included). Constructed of formed 304 stainless steel for corrosion resistance. Design features flanged ends to provide a larger mounting surface for greater durability. Functional and attractive, with no visible mounting hardware.

Stainless Steel Stud Mount Flanged Hand Rail with Mounting Flange - 18"  These Stud Mounted Flanged Hand Rail features integral 5/16”-18 threaded studs and installs with two 5/16”-18 nuts (not included). Constructed of formed 304 stainless steel for corrosion resistance. Design features flanged ends to provide a larger mounting surface for greater durability. Functional and attractive, with no visible mounting hardware.

Stainless Steel Stud Mount Flanged Hand Rail with Mounting Flange - 24"  These Stud Mounted Flanged Hand Rail features integral 5/16”-18 threaded studs and installs with two 5/16”-18 nuts (not included). Constructed of formed 304 stainless steel for corrosion resistance. Design features flanged ends to provide a larger mounting surface for greater durability. Functional and attractive, with no visible mounting hardware.

Stainless Steel Stud Mount Flanged Hand Rail with Mounting Flange - 10"  These Stud Mounted Flanged Hand Rail features integral 5/16”-18 threaded studs and installs with two 5/16”-18 nuts (not included). Constructed of formed 304 stainless steel for corrosion resistance. Design features flanged ends to provide a larger mounting surface for greater durability. Functional and attractive, with no visible mounting hardware.

Grand Slam 850 Electric VHF Antenna Mount Designed with safety and innovation in mind, boaters can adjust the position of their VHF antenna with the simple push of a button from the comfort of their helm. The GS-850 is a fully electric unit with hidden wires inside the hardtop. This mount easily installs to the surface of the hardtop and fits all top thicknesses. Features: Standard 1”-14 thread (male) shaft to accept standard VHF antennas  No under-mount clearance required  Machined / Anodized aluminum body with a light brushed finish  Threaded shaft for consistent lift and descent  Delrin bearings for smooth operation  Features removable set screw for manual adjustment  Kit includes drill template and installation instructions  Includes 10” lead for 12-volt DC power supply for lift and descent  Accepts 3A fuse in the main +12 VDC power feed (not included)  Sold individually  Made in the USA  1-year limited warranty

Gen 3 Standard Starlink Antenna Mount with 8 Degree Wedge Base The Seaview SRM200W Mount for the Gen 3 Standard Starlink Antenna (sometimes Gen 4 / Standard) has been specifically designed for the harsh marine environment. If it's good for the marine environment then it's ideal for any other outdoor application (RVs, overland vehicles, vans, jeeps, side-by-side, UTV, trucks, etc.). The base aluminum plate has a 3 part polyurethane prime and powder coat and the end pieces are made using machined marine-grade high-density polyethylene to ensure the best possible finish and corrosion resistance.  The Gen 3 Standard Starlink Antenna (sometimes Gen 4 / Standard) now features a convenient pressure-fit kickstand for placement on flat non-mobile surfaces. However, marine or vehicle mounting necessitates additional support. Opting for the Seaview SRM200W Mount is a superior choice, offering a reliable and adaptable mounting solution. You have the option to utilize through-bolts for a permanent fixture through machined holes in the mount's base or pair it with the Seaview 8° Wedge base for a highly versatile installation. *The SRM200W can be mounted directly or it can be mounted to the Starlink 8° Wedge Base (SVSLWB). Wedge Base Features: Designed to fit the Starlink Flat High-Performance Antenna and Seaview SRM200W Mount for the Gen 3 Standard Starlink Antenna.  Pre-drilled mounting holes allow the hardware to fasten directly to the wedge. Drilled and tapped for the CG30PW (white) or CG30PB (black) cable seal that comes with each Seaview wedge base. No need to cut the Starlink connectors for installation. Available in white or black

Horizontal Rail Accessory Mount - 3" Disk Edson’s Stainless Horizontal Rail Accessory Mount puts your hand-held GPS securely and conveniently within reach on your Steering Pedestal Guard. With its 3" Disk Platform you can mount your GPS hand held or other items that need a secured place to stay. Designed to attach to all 1”, 1-1/8” and 1-1/4” pedestal guard tubes by clamping the two pieces together around the guard tube without the need for removal of the tubes or any existing wiring.

Horizontal Rail Accessory Mount - 5" Disk Edson’s Stainless Horizontal Rail Accessory Mount puts your hand-held GPS securely and conveniently within reach on your Steering Pedestal Guard. With its 5" Disk Platform you can mount your GPS hand held or other items that need a secured place to stay. Designed to attach to all 1”, 1-1/8” and 1-1/4” pedestal guard tubes by clamping the two pieces together around the guard tube without the need for removal of the tubes or any existing wiring.

Gen 3 Standard Starlink Antenna Mount The Seaview SRM200W Mount for the Gen 3 Standard Starlink Antenna (sometimes Gen 4 / Standard) has been specifically designed for the harsh marine environment. If it's good for the marine environment then it's ideal for any other outdoor application (RVs, overland vehicles, vans, jeeps, side-by-side, UTV, trucks, etc.). The base aluminum plate has a 3 part polyurethane prime and powder coat and the end pieces are made using machined marine-grade high-density polyethylene to ensure the best possible finish and corrosion resistance.  The Gen 3 Standard Starlink Antenna (sometimes Gen 4 / Standard) now features a convenient pressure-fit kickstand for placement on flat non-mobile surfaces. However, marine or vehicle mounting necessitates additional support. Opting for the Seaview SRM200W Mount is a superior choice, offering a reliable and adaptable mounting solution. You have the option to utilize through-bolts for a permanent fixture through machined holes in the mount's base or pair it with the Seaview 8° Wedge base for a highly versatile installation. *The SRM200W can be mounted directly or it can be mounted to the Starlink 8° Wedge Base (SVSLWB).

Standard Support w/4-Way Base - 1.5" Collar A perfect blend of form and function, Antenna Mounting Systems by Rupp combine good looks with innovative designs. The locking collar holds antenna securely, yet unlocks conveniently for lowering. Made of forged and anodized aluminum for strength and long lasting beauty. Standard supports are designed for easy mounting to cabin sides. Features: Base: Oval 4-Way Spacer: No Bolts: No