90 degree mounting bezel for T73NRFC Non-Reversible Steering System

As the Fall months creep into our calendars, boat owners in cooler climates acknowledge, with sadness, that it’s time to put the boat away. Outside Storage? It’s a thought and an option but consider that you may be threatened by snow build up, tornadoes or hurricanes. The success of storing your boat outside depends on how well your boat is protected from the conditions outdoors.                          Rinse/Flush Rinsing the outside of your boat and trailer thoroughly with fresh water will remove excess salt. Pay particular attention to your trailer’s leaf springs, wheel hubs and brakes that are constantly submerged during launching and retrieval of your boat. Flush your engine's cooling system with fresh water in line with your engine manufacturer’s salt removal recommendations. This will minimize corrosion and overheating issues come spring. Drain your boat of all water – bilge, head, sink lines, water tanks, sea-cocks, and pipes. If you are in an area with extended periods of freezing, put antifreeze in the low parts if there is still some water present. Salt Watch out for salt. Buy a good salt remover to minimize corrosion. Add fuel stabilizer to top off your fuel tanks. Here is one recommended by CLR Marine. Diesel Formula Fuel Stabilizer & Performance Improver - 32oz *Case of 4* STA-BIL Diesel Formula Fuel Stabilizer is a diesel additive that keeps fuel fresh for quick, easy starts and maximized for engine performance. Designed for use with all diesel engines, and all diesel fuels, Sta-Bil Fuel Stabilizer Diesel formula prevents sludge and sediment formation, cleans and lubricates fuel injectors to improve performance and helps remove water. It is safe to use and recommended for use at every fill up, with the 32 ounce bottle treating up to 320 gallons of fuel. Batteries Remove the batteries from your boat and store in your garage or basement. Batteries should be connected to a battery charger that will give them a good charge and one that w automatically switches to a float/trickle charge to keep your batteries topped up. Match your charger to the type of battery you are charging. Using a charger manufactured for lead acid batteries to charge an AGM (absorbent glass mat) battery will cause damage to the battery. If you choose to keep your batteries in the boat, connect a solar trickle charger. These chargers will keep your batteries topped off without the hassle of removing heavy batteries from your boat. Cleaning Clean the exterior with the proper fiber glass or wood cleaner needed for your boat. Bright work can be cleaned by removing the wood or cleaning it as it is - installed. Be careful to not get the wood cleaner onto the deck surfaces. The exterior should be dried with a chamois cloth. Vinyl seat cushions and backs should be cleaned with vinyl cleaner. Hard surfaces inside the vessel can be wiped with all purpose cleaners. End your cleaning with a coat of wax to the exterior and polish. Don’t forget the bottom paint. Before you store, spend the time to give your boat a thorough cleaning. CLR Marine has many products by trusted brands such as Powerhouse, Davis Instruments, Jabsco, Shurhold, and Swobbit, to help winterize and clean. You will be grateful in the spring during launch time that your boat is already clean as the new boating season begins. Cover Up If you store outside in your yard, driveway, or a boat yard, a boat cover is a must to prevent damage from winter conditions. Leaving your boat in the water is not recommended. The boat is exposed to rough weather, and has a greater possibility of sinking if you aren’t monitoring it often. https://www.clrmarine.com/462m4/boat-outfitting/winter-covers.html and https://www.clrmarine.com/462m4/winterizing.html Circle May 21, 2022, on your calendar. The date is almost ten days before Memorial Day, next year when most harbors open for the season. Start your prep work, tune-ups, sanding, and painting to get out on the water and a great boating season. In the meantime, during the cold winter months, cozy up to the fire and read your boating manuals, new safety regulations and weather information. Fair winds and smooth sailing.   To obtain more information about the products and services mentioned in this article, please get in touch with CLR Marine https://www.clrmarine.com/. _________________________________________________________________________ Award-winning author Cheryl Kuba has been at the helm for more than 30 years sailing the Great Lakes, with side trips to the British Virgin Islands and St. Maarten. She has served as past- Commodore of Great Lakes Fleet 21 -Chicago region. 3happycampers.com ©Copyright Cheryl Kuba, 3happycampers.com, 2021.  

RAM® Tilt-N-Turn™ 90-Degree Bracket with Single Swing Arm The RAM-VB-TNT90-1, Tilt-N-Turn™ 90 degree motion attachment swing arm, consists of a steel plate on a single swing arm that has a tilt range of 90 degrees forward and back from the vertical position. The small range of tilt is designed to angle a connected RAM laptop cradle forward giving you a comfortable typing and viewing angle. The Tilt-N-Turn™ plate can spin in 360 degrees around on the swing arm end, and with a twist of the side lock knob, the attachment will tilt forward and back. Knowing that this product has countless applications, numerous hole patterns are built right in making the Tilt-N-Turn™ exceptionally versatile. The AMPS, 90 degree AMPS, 75 x 75MM VESA, 2” x 4”, and RAM’s own three hole at 120 degrees take the guess work out of whether this product will work for you. Whether you have and existing RAM system and want to integrate this product, or simply need the best mounting system available, consider RAM and yet another ergonomic product; this time with the Tilt-and-Turn™ feature.  Hardware Included: (1) 3/8"-16 x 1.5" Carriage Bolt (1) 3/8"-18 Lock Nut (1) 2" Rubber Washer (2) 5/16" Flat Washer Materials:  Powder coated steel Marine grade-aluminum

3" ID 90-Degree EPDM Black Rubber Molded Wet Exhaust Elbow with 4 T-Bolt Clamps Trident EPDM marine wet exhaust connections are molded of high-temperature black EPDM rubber with a smooth bore and cover; except elbows of 6” I.D. or bigger have molded reinforcing ribs on the outside. Features: Four stainless steel clamps are included This elbow has excellent resistance to ozone, salt water, diesel fumes and splashes, cold, heat, and aging Exceeds (SAE J2006-R1, and ABYC & NMMA P-1 exhaust standards) Black high-temp EDPM rubber  Construction: Color: Black Reinforcement: Reinforcing ribs on 6” I.D. and above Temperature Range: up to 250°F (121°C) Specifications: Inner Diameter: (inch) 3” / (mm) 76.2 A: (inch) 5.25" / (mm) 133 B: (inch) 5.25” / (mm) 133 C: (inch) 1.75” / (mm) 44.4 D: (inch) 1.75” / (mm) 44.4 R: (inch) 2” / (mm) 50.8 W: (inch) 0.25” / (mm) 6.4 Elbow Degree: 90 degrees

6" ID 90-Degree EPDM Black Rubber Molded Wet Exhaust Elbow with 4 T-Bolt Clamps Trident EPDM marine wet exhaust connections are molded of high-temperature black EPDM rubber with a smooth bore and cover; except elbows of 6” I.D. or bigger have molded reinforcing ribs on the outside. Features: Four stainless steel clamps are included This elbow has excellent resistance to ozone, salt water, diesel fumes and splashes, cold, heat, and aging Exceeds (SAE J2006-R1, and ABYC & NMMA P-1 exhaust standards) Black high-temp EDPM rubber Construction: Color: Black Reinforcement: Reinforcing ribs on 6” I.D. and above Temperature Range: up to 250°F (121°C) Specifications: Inner Diameter: (inch) 6” / (mm) 152.4 A: (inch) 7" / (mm) 178 B: (inch) 7” / (mm) 178 C: (inch) 2.25” / (mm) 57 D: (inch) 2.25” / (mm) 57 R: (inch) 1.75” / (mm) 44.4 W: (inch) 0.25” / (mm) 6.4 Elbow Degree: 90 degrees

4" ID 90-Degree EPDM Black Rubber Molded Wet Exhaust Elbow with 4 T-Bolt Clamps Trident EPDM marine wet exhaust connections are molded of high-temperature black EPDM rubber with a smooth bore and cover; except elbows of 6” I.D. or bigger have molded reinforcing ribs on the outside. Features: Four stainless steel clamps are included This elbow has excellent resistance to ozone, salt water, diesel fumes and splashes, cold, heat, and aging Exceeds (SAE J2006-R1, and ABYC & NMMA P-1 exhaust standards) Black high-temp EDPM rubber Construction: Color: Black Reinforcement: Reinforcing ribs on 6” I.D. and above Temperature Range: up to 250°F (121°C) Specifications: Inner Diameter: (inch) 4” / (mm) 101.6 A: (inch) 5.75" / (mm) 146 B: (inch) 5.75” / (mm) 146 C: (inch) 1.75” / (mm) 44.4 D: (inch) 1.75” / (mm) 44.4 R: (inch) 2” / (mm) 50.8 W: (inch) 0.25” / (mm) 6.4 Elbow Degree: 90 degrees

Perko 3/4" Pipe To Hose Adapter 90 Degree Bronze Cast Bronze Cast hex for easier installation Curved 90 degrees Technical Information: Pipe Size Inches: 3/4 Hose Size Inches: 3/4 Length Overall Inches: 4-1/2 Model Number: 0063DP5PLB Ship Weight: 2.1/9.1 *The above item meets the requirements of U.S.C.G. Safety Standards, January 31, 1977 for gasoline fuel systems, 33 CFR 183.

Perko 1" Pipe To Hose Adapter 90 Degree Bronze Cast Bronze Cast hex for easier installation Curved 90 degrees Technical Information: Pipe Size Inches: 1 Hose Size Inches: 1 Length Overall Inches: 4-3/4 Model Number: 0063DP6PLB Ship Weight: 3.7/16.9 *The above item meets the requirements of U.S.C.G. Safety Standards, January 31, 1977 for gasoline fuel systems, 33 CFR 183.

Perko 1-1/4" Pipe To Hose Adapter 90 Degree Bronze Cast Bronze Cast hex for easier installation Curved 90 degrees Technical Information: Pipe Size Inches: 1-1/4 Hose Size Inches: 1-1/4 Length Overall Inches: 5-1/2 Model Number: 0063DP7PLB Ship Weight: 5.5/25.3 *The above item meets the requirements of U.S.C.G. Safety Standards, January 31, 1977 for gasoline fuel systems, 33 CFR 183.

Perko 1-1/2" Pipe To Hose Adapter 90 Degree Bronze Cast Bronze Cast hex for easier installation Curved 90 degrees Technical Information: Pipe Size Inches: 1-1/2 Hose Size Inches: 1-1/2 Length Overall Inches: 6 Model Number: 0063DP8PLB Ship Weight: 7.5/14.6 *The above item meets the requirements of U.S.C.G. Safety Standards, January 31, 1977 for gasoline fuel systems, 33 CFR 183.

Perko 2" Pipe To Hose Adapter 90 Degree Bronze Cast Bronze Cast hex for easier installation Curved 90 degrees Technical Information: Pipe Size Inches: 2 Hose Size Inches: 2 Length Overall Inches: 7 Model Number: 0063009PLB Ship Weight: 2.9/27.1 *The above item meets the requirements of U.S.C.G. Safety Standards, January 31, 1977 for gasoline fuel systems, 33 CFR 183.

3" ID 90-Degree Blue Silicone Molded Wet Exhaust Elbow with 4 T-Bolt Clamps Trident silicone-blend rubber marine wet exhaust connections. They are molded in very high-temperature blue silicone EPDM blended rubber with a smooth bore and cover.  Features: Four stainless steel t-bolt clamps Very high temp silicone/EDPM blend rubber - molded This elbow has excellent resistance to ozone, salt water, diesel fumes, splash, cold, heat, and aging Exceeds (SAE J2006-R1, and ABYC & NMMA P-1) exhaust standards  Blue very high-temperature silicone blended with EDPM rubber at 350°F (177°C) max continuous Construction: Color: Blue Temperature Range: up to 350°F (177°C) Specifications: Inner Diameter: (inch) 3” / (mm) 76.2 A: (inch) 5.25” / (mm) 133 B: (inch) 5.25” / (mm) 133 C: (inch) 1.75” / (mm) 44.4 D: (inch) 1.50" / (mm) 38.1 R: (inch) 2” / (mm) 50.8 W: (inch) 0.25" / (mm) 6.4 Elbow Degree: 90 degrees 

4" ID 90-Degree Blue Silicone Molded Wet Exhaust Elbow with 4 T-Bolt Clamps Trident silicone-blend rubber marine wet exhaust connections. They are molded in very high-temperature blue silicone EPDM blended rubber with a smooth bore and cover.  Features: Four stainless steel t-bolt clamps Very high temp silicone/EDPM blend rubber - molded This elbow has excellent resistance to ozone, salt water, diesel fumes, splash, cold, heat, and aging Exceeds (SAE J2006-R1, and ABYC & NMMA P-1) exhaust standards  Blue very high-temperature silicone blended with EDPM rubber at 350°F (177°C) max continuous Construction: Color: Blue Temperature Range: up to 350°F (177°C) Specifications: Inner Diameter: (inch) 4” / (mm) 101.6 A: (inch) 5.75” / (mm) 146 B: (inch) 5.75” / (mm) 146 C: (inch) 1.75” / (mm) 44.4 D: (inch) 1.50" / (mm) 38.1 R: (inch) 2” / (mm) 50.8 W: (inch) 0.25" / (mm) 6.4 Elbow Degree: 90 degrees

6" ID 90-Degree Blue Silicone Molded Wet Exhaust Elbow with 4 T-Bolt Clamps Trident silicone-blend rubber marine wet exhaust connections. They are molded in very high-temperature blue silicone EPDM blended rubber with a smooth bore and cover; except elbows of 6" I.D. or larger have molded reinforcing ribs on the outside.  Features: Four stainless steel t-bolt clamps Very high temp silicone/EDPM blend rubber - molded This elbow has excellent resistance to ozone, salt water, diesel fumes, splash, cold, heat, and aging Exceeds (SAE J2006-R1, and ABYC & NMMA P-1) exhaust standards  Blue very high-temperature silicone blended with EDPM rubber at 350°F (177°C) max continuous Construction: Color: Blue Reinforcement: Reinforcing ribs on 6” I.D. and above Temperature Range: up to 350°F (177°C) Specifications: Inner Diameter: (inch) 6” / 152.4 mm A: (inch) 7” / (mm) 178  B: (inch) 7” / (mm) 178  C: (inch) 2.25” / (mm) 57.2 D: (inch) 2" / (mm) 57.2 R: (inch) 1.75” / (mm) 44.5 W: (inch) 0.25" / (mm) 6.4 Elbow Degree: 90 degrees

RhinoFLEX 90-Degree Swivel Fitting Clear RhinoFLEX Swivel Fittings Transparent or semi-translucent fittings connect sewer hose to waste valve fitting. Features swivel lug and bayonet fittings for a secure connection. Available in 45° or 90° style.  Features: 90-degree swivel fitting Clear fitting to see if holding tank is empty Swivel lug and bayonet fitting for secure connection UV stabilized resin for long life Connect sewer hose to your RV’s waste valve fitting