Insta-Trim Boat Leveler 12 Volt Solenoid Valve with Green Wire. They are custom designed for Insta-Trim Boat Leveler Co., epoxy sealed and humidity resistant, thereby preventing shorting out. The solenoids lock the tabs in any position, eliminating driftback. Barb type hose fittings provide tight, secure connections.

Insta-Trim Boat Leveler 12 Volt Solenoid Valve with White Wire. They are custom designed for Insta-Trim Boat Leveler Co., epoxy sealed and humidity resistant, thereby preventing shorting out. The solenoids lock the tabs in any position, eliminating driftback. Barb type hose fittings provide tight, secure connections.

Solenoid Valve - Green - 24V Replacement Solenoid Valve for use with Bennett's Hydraulic Power Unit Solenoid valves direct the flow of fluid to the actuators. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Solenoid valves direct the flow of fluid to the actuators. The solenoid valves lock tightly to secure the tabs in place. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

As the Fall months creep into our calendars, boat owners in cooler climates acknowledge, with sadness, that it’s time to put the boat away. Outside Storage? It’s a thought and an option but consider that you may be threatened by snow build up, tornadoes or hurricanes. The success of storing your boat outside depends on how well your boat is protected from the conditions outdoors.                          Rinse/Flush Rinsing the outside of your boat and trailer thoroughly with fresh water will remove excess salt. Pay particular attention to your trailer’s leaf springs, wheel hubs and brakes that are constantly submerged during launching and retrieval of your boat. Flush your engine's cooling system with fresh water in line with your engine manufacturer’s salt removal recommendations. This will minimize corrosion and overheating issues come spring. Drain your boat of all water – bilge, head, sink lines, water tanks, sea-cocks, and pipes. If you are in an area with extended periods of freezing, put antifreeze in the low parts if there is still some water present. Salt Watch out for salt. Buy a good salt remover to minimize corrosion. Add fuel stabilizer to top off your fuel tanks. Here is one recommended by CLR Marine. Diesel Formula Fuel Stabilizer & Performance Improver - 32oz *Case of 4* STA-BIL Diesel Formula Fuel Stabilizer is a diesel additive that keeps fuel fresh for quick, easy starts and maximized for engine performance. Designed for use with all diesel engines, and all diesel fuels, Sta-Bil Fuel Stabilizer Diesel formula prevents sludge and sediment formation, cleans and lubricates fuel injectors to improve performance and helps remove water. It is safe to use and recommended for use at every fill up, with the 32 ounce bottle treating up to 320 gallons of fuel. Batteries Remove the batteries from your boat and store in your garage or basement. Batteries should be connected to a battery charger that will give them a good charge and one that w automatically switches to a float/trickle charge to keep your batteries topped up. Match your charger to the type of battery you are charging. Using a charger manufactured for lead acid batteries to charge an AGM (absorbent glass mat) battery will cause damage to the battery. If you choose to keep your batteries in the boat, connect a solar trickle charger. These chargers will keep your batteries topped off without the hassle of removing heavy batteries from your boat. Cleaning Clean the exterior with the proper fiber glass or wood cleaner needed for your boat. Bright work can be cleaned by removing the wood or cleaning it as it is - installed. Be careful to not get the wood cleaner onto the deck surfaces. The exterior should be dried with a chamois cloth. Vinyl seat cushions and backs should be cleaned with vinyl cleaner. Hard surfaces inside the vessel can be wiped with all purpose cleaners. End your cleaning with a coat of wax to the exterior and polish. Don’t forget the bottom paint. Before you store, spend the time to give your boat a thorough cleaning. CLR Marine has many products by trusted brands such as Powerhouse, Davis Instruments, Jabsco, Shurhold, and Swobbit, to help winterize and clean. You will be grateful in the spring during launch time that your boat is already clean as the new boating season begins. Cover Up If you store outside in your yard, driveway, or a boat yard, a boat cover is a must to prevent damage from winter conditions. Leaving your boat in the water is not recommended. The boat is exposed to rough weather, and has a greater possibility of sinking if you aren’t monitoring it often. https://www.clrmarine.com/462m4/boat-outfitting/winter-covers.html and https://www.clrmarine.com/462m4/winterizing.html Circle May 21, 2022, on your calendar. The date is almost ten days before Memorial Day, next year when most harbors open for the season. Start your prep work, tune-ups, sanding, and painting to get out on the water and a great boating season. In the meantime, during the cold winter months, cozy up to the fire and read your boating manuals, new safety regulations and weather information. Fair winds and smooth sailing.   To obtain more information about the products and services mentioned in this article, please get in touch with CLR Marine https://www.clrmarine.com/. _________________________________________________________________________ Award-winning author Cheryl Kuba has been at the helm for more than 30 years sailing the Great Lakes, with side trips to the British Virgin Islands and St. Maarten. She has served as past- Commodore of Great Lakes Fleet 21 -Chicago region. 3happycampers.com ©Copyright Cheryl Kuba, 3happycampers.com, 2021.  

Propane Fume Detector, 2 Channel, 2 Sensors, Solenoid Valve & Control & 20' Cable - 24V DC  Propane has become the fuel of choice for cooking and heating. Highly BTU-efficient and readily available, propane is becoming more and more a part of power boating, sailing, and camping. The Xintex® line of propane products includes everything you need for outfitting a complete and safe propane system. Propane is heavier than air and can settle below deck and in the bilge where it can be detonated by an engine start-up or electrical spark of any kind. Xintex® Propane Fume Detectors will alarm when fumes reach 18-20% LEL.  *Includes Time Sensor Valve

Propane Fume Detector w/Plastic Sensor & Solenoid Valve - Black Bezel Display Detect propane leaks early and automatically shut off gas supply to prevent personal injury and possible explosions. Features/Specifications: 2-3/16" Round Black Display with LEDs & Silence/Test Button Solenoid Valve & Adapter Solenoid Valve Control Button Automatically Closes Solenoid Valve 68 dBA Alarm will sound & Red LED will light at 20% of the LEL Simple Installation 9-30VDC Operating Temperature: -40°F to 185°F (-40°C to 85°C) Reverse Polarity Protected Current Draw @ 12VDC: Nominal:55mA / Maximum:725mA

Deluxe Flush 17" Angled Back 12V Freshwater Electric Marine Toilet with Solenoid Valve & Soft Close Lid You can experience all the comforts of home at sea with Jabsco Deluxe Flush electric marine toilet. Designed for the discerning owner looking for luxury and comfort, the Deluxe Flush portfolio features a space-saving, stylish design with minimal water usage and virtually silent operation. Features: 17" Angled back Space-saving stylish design Household size soft closing seat Virtually silent operation Fresh water rinse model Powerful non-clogging large bore flush pump macerates waste Specifications: Bowl Size: Domestic Lid: Soft close Rinse Type: Freshwater Rinse Pump/Solenoid Valve: Solenoid valve Voltage DC: 12V DC Recommended fuse Size (AMP): 25 Flush control Switch: 4-Button Touch Panel Height: (inch) 17.5” / (mm) 445 Width: (inch) 14.8” / (mm) 375 Depth: (inch) 17.7" / (mm) 450 Weight: (LBS) 61.7" / (kg) 28 One-Touch Control Pad: All Deluxe Flush marine toilets come complete with a multi-function, one-touch control pad. The control pad is supplied with a standard surface mount unit with a clean white bezel.  The control pad offers four options: fill, quick flush, flush, or empty. In addition, the owner can set the control at any time so that the bowl is always left either dry or wet after flushing. The recommended dry setting minimizes total water usage. If water usage is not a concern, the wet location automatically fills the bowl after flushing, ready for the next user. Simultaneously holding down both the quick flush and flush buttons for 5 seconds switches between bowl always left dry and bowled always left wet modes. Control Pad Options: Fill may be touched when the bowl is dry add 1 quart (1 liter) of water before use, if necessary Quick Flush first rinses and then empties the bowl after light use. On the dry setting, this uses less than 1 quart (1 liter) of water Flush rinses and empties the bowl twice after heavy use. If the bowl is dry, touching the fill before use is recommended. This uses just 2.5 quarts (2.5 liters) of water Empty does exactly what it says without adding any water, whenever desired. Even when the bowl appears to be dry, there is an anti-odor water lock in the pump housing Rinse Options: Supplied with a solenoid valve assembly for connection to any existing pressurized water system capable of delivering 2.9 GPM (11 LPM) or more The solenoid valve features dual non-return valves to protect the freshwater system from possible black flow from the toilet into the water system

Deluxe Flush 14" Angled Back 12V Freshwater Electric Marine Toilet with Solenoid Valve & Soft Close Lid You can experience all the comforts of home at sea with Jabsco Deluxe Flush electric marine toilet. Designed for the discerning owner looking for luxury and comfort, the Deluxe Flush portfolio features a space-saving, stylish design with minimal water usage and virtually silent operation. Features: 14" Angled back Space-saving stylish design Household size soft closing seat Virtually silent operation Fresh water rinse model Powerful non-clogging large bore flush pump macerates waste Specifications: Bowl Size: Domestic Lid: Soft close Rinse Type: Freshwater Rinse Pump/Solenoid Valve: Solenoid valve Voltage DC: 12V DC Recommended fuse Size (AMP): 25 Flush control Switch: 4-Button Touch Panel Height: (inch) 14.4” / (mm) 366 Width: (inch) 14.8” / (mm) 375 Depth: (inch) 17.7" / (mm) 450 Weight: (LBS) 59.5" / (kg) 27 One-Touch Control Pad: All Deluxe Flush marine toilets come complete with a multi-function, one-touch control pad. The control pad is supplied with a standard surface mount unit with a clean white bezel.  The control pad offers four options: fill, quick flush, flush, or empty. In addition, the owner can set the control at any time so that the bowl is always left either dry or wet after flushing. The recommended dry setting minimizes total water usage. If water usage is not a concern, the wet location automatically fills the bowl after flushing, ready for the next user. Simultaneously holding down both the quick flush and flush buttons for 5 seconds switches between bowl always left dry and bowled always left wet modes. Control Pad Options: Fill may be touched when the bowl is dry add 1 quart (1 liter) of water before use, if necessary Quick Flush first rinses and then empties the bowl after light use. On the dry setting, this uses less than 1 quart (1 liter) of water Flush rinses and empties the bowl twice after heavy use. If the bowl is dry, touching the fill before use is recommended. This uses just 2.5 quarts (2.5 liters) of water Empty does exactly what it says without adding any water, whenever desired. Even when the bowl appears to be dry, there is an anti-odor water lock in the pump housing Rinse Options: Supplied with a solenoid valve assembly for connection to any existing pressurized water system capable of delivering 2.9 GPM (11 LPM) or more The solenoid valve features dual non-return valves to protect the freshwater system from possible black flow from the toilet into the water system

Deluxe Flush 14" Angled Back 24V Freshwater Electric Marine Toilet with Solenoid Valve & Soft Close Lid You can experience all the comforts of home at sea with Jabsco Deluxe Flush electric marine toilet. Designed for the discerning owner looking for luxury and comfort, the Deluxe Flush portfolio features a space-saving, stylish design with minimal water usage and virtually silent operation. Features: 14" Angled back Space-saving stylish design Household size soft closing seat Virtually silent operation Fresh water rinse model Powerful non-clogging large bore flush pump macerates waste Specifications: Bowl Size: Domestic Lid: Soft close Rinse Type: Freshwater Rinse Pump/Solenoid Valve: Solenoid valve Voltage DC: 24V DC Recommended fuse Size (AMP): 15 Flush control Switch: 4-Button Touch Panel Height: (inch) 14.4” / (mm) 366 Width: (inch) 14.8” / (mm) 375 Depth: (inch) 17.7" / (mm) 450 Weight: (LBS) 59.5" / (kg) 27 One-Touch Control Pad: All Deluxe Flush marine toilets come complete with a multi-function, one-touch control pad. The control pad is supplied with a standard surface mount unit with a clean white bezel.  The control pad offers four options: fill, quick flush, flush, or empty. In addition, the owner can set the control at any time so that the bowl is always left either dry or wet after flushing. The recommended dry setting minimizes total water usage. If water usage is not a concern, the wet setting automatically fills the bowl after flushing, ready for the next user. Simultaneously holding down both the quick flush and flush buttons for 5 seconds switches between bowl always left dry and bowled always left wet modes. Control Pad Options: Fill may be touched when the bowl is dry add 1 quart (1 liter) of water before use, if necessary Quick Flush first rinses and then empties the bowl after light use. On the dry setting, this uses less than 1 quart (1 liter) of water Flush rinses and empties the bowl twice after heavy use. If the bowl is dry, touching the fill before use is recommended. This uses just 2.5 quarts (2.5 liters) of water Empty does exactly what it says without adding any water, whenever desired. Even when the bowl appears to be dry, there is an anti-odor water lock in the pump housing Rinse Options: Supplied with a solenoid valve assembly for connection to any existing pressurized water system capable of delivering 2.9 GPM (11 LPM) or more The solenoid valve features dual non-return valves to protect the freshwater system from possible black flow from the toilet into the water system

Deluxe Flush 14" Straight Back 12V Freshwater Electric Marine Toilet with Solenoid Valve & Soft Close Lid You can experience all the comforts of home at sea with Jabsco Deluxe Flush electric marine toilet. Designed for the discerning owner looking for luxury and comfort, the Deluxe Flush portfolio features a space-saving, stylish design with minimal water usage and virtually silent operation. Features: 14" Straight back Space-saving stylish design Household size soft closing seat Virtually silent operation Fresh water rinse model Powerful non-clogging large bore flush pump macerates waste Specifications: Bowl Size: Domestic Lid: Soft close Rinse Type: Freshwater Rinse Pump/Solenoid Valve: Solenoid valve Voltage DC: 12V DC Recommended fuse Size (AMP): 25 Flush control Switch: 4-Button Touch Panel Height: (inch) 14.4” / (mm) 366 Width: (inch) 14.8” / (mm) 375 Depth: (inch) 17.7" / (mm) 450 Weight: (LBS) 55.1" / (kg) 25 One-Touch Control Pad: All Deluxe Flush marine toilets come complete with a multi-function, one-touch control pad. The control pad is supplied with a standard surface mount unit with a clean white bezel.  The control pad offers four options: fill, quick flush, flush, or empty. In addition, the owner can set the control at any time so that the bowl is always left either dry or wet after flushing. The recommended dry setting minimizes total water usage. If water usage is not a concern, the wet setting automatically fills the bowl after flushing, ready for the next user. Simultaneously holding down both the quick flush and flush buttons for 5 seconds switches between bowl always left dry and bowled always left wet modes. Control Pad Options: Fill may be touched when the bowl is dry add 1 quart (1 liter) of water before use, if necessary Quick Flush first rinses and then empties the bowl after light use. On the dry setting, this uses less than 1 quart (1 liter) of water Flush rinses and empties the bowl twice after heavy use. If the bowl is dry, touching the fill before use is recommended. This uses just 2.5 quarts (2.5 liters) of water Empty does exactly what it says without adding any water, whenever desired. Even when the bowl appears to be dry, there is an anti-odor water lock in the pump housing Rinse Options: Supplied with a solenoid valve assembly for connection to any existing pressurized water system capable of delivering 2.9 GPM (11 LPM) or more The solenoid valve features dual non-return valves to protect the freshwater system from possible black flow from the toilet into the water system

Deluxe Flush 14" Straight Back 24V Freshwater Electric Marine Toilet with Solenoid Valve & Soft Close Lid You can experience all the comforts of home at sea with Jabsco Deluxe Flush electric marine toilet. Designed for the discerning owner looking for luxury and comfort, the Deluxe Flush portfolio features a space-saving, stylish design with minimal water usage and virtually silent operation. Features: 14" Straight back Space-saving stylish design Household size soft closing seat Virtually silent operation Fresh water rinse model Powerful non-clogging large bore flush pump macerates waste Specifications: Bowl Size: Domestic Lid: Soft close Rinse Type: Freshwater Rinse Pump/Solenoid Valve: Solenoid valve Voltage DC: 24 Recommended fuse Size (AMP): 15 Flush control Switch: 4-Button Touch Panel Height: (inch) 14.4” / (mm) 366 Width: (inch) 14.8” / (mm) 375 Depth: (inch) 17.7" / (mm) 450 Weight: (LBS) 55.1" / (kg) 25 One-Touch Control Pad: All Deluxe Flush marine toilets come complete with a multi-function, one-touch control pad. The control pad is supplied with a standard surface mount unit with a clean white bezel.  The control pad offers four options: fill, quick flush, flush, or empty. In addition, the owner can set the control at any time so that the bowl is always left either dry or wet after flushing. The recommended dry setting minimizes total water usage. If water usage is not a concern, the wet setting automatically fills the bowl after flushing, ready for the next user. Simultaneously holding down both the quick flush and flush buttons for 5 seconds switches between bowl always left dry and bowled always left wet modes. Control Pad Options: Fill may be touched when the bowl is dry add 1 quart (1 liter) of water before use, if necessary Quick Flush first rinses and then empties the bowl after light use. On the dry setting, this uses less than 1 quart (1 liter) of water Flush rinses and empties the bowl twice after heavy use. If the bowl is dry, touching the fill before use is recommended. This uses just 2.5 quarts (2.5 liters) of water Empty does exactly what it says without adding any water, whenever desired. Even when the bowl appears to be dry, there is an anti-odor water lock in the pump housing Rinse Options: Supplied with a solenoid valve assembly for connection to any existing pressurized water system capable of delivering 2.9 GPM (11 LPM) or more The solenoid valve features dual non-return valves to protect the freshwater system from possible black flow from the toilet into the water system

Vented Loop Solenoid Valve for 37010 Series Toilet When installing a vented loop in the inlet hose, it is recommended that a Vented Loop Solenoid Valve (37068-2000) is connected to the vent air inlet to ensure maximum electric toilet performance and prime-ability. Connect the brass port of the valve (remove plastic filter, if installed) with the air inlet of the vented loop. Wire the solenoid valve in parallel with the toilet motor by connecting one side of the solenoid to the toilet flush switch and the other side to battery ground. WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Jabsco 37038-2024 Solenoid Valve 24V ANTI-SYPHON SOLENOID VALVE 24V Solenoid valve for use with Quiet Flush fresh water toilets Inline, normally closed solenoid valve. Supplied with 15mm (1/2”) JG Speed fit connections, 15mm (1/2”) hose barb inlet, 19mm (3/4”) Hose barb outlet Double check valve to protect against contamination of potable water Internal inlet filter   Mountable in any orientation, above or below toilet Mounting bracket included 

Propane Fume Detector with Plastic Sensor & Solenoid Valve - Chrome Bezel Display Detect propane leaks early and automatically shut off gas supply to prevent personal injury and possible explosions. Features: 2-3/16" Round Chrome Display with LEDs & Silence/Test Button Solenoid Valve & Adapter Solenoid Valve Control Button Automatically Closes Solenoid Valve 68 dBA Alarm will sound & Red LED will light at 20% of the LEL Simple Installation 9-30VDC Operating Temperature: -40°F to 185°F (-40°C to 85°C) Reverse Polarity Protected Current Draw @ 12VDC: Nominal: 55mA/Maximum: 725mA