Force Nose Cone with Transducer Replacement Kit - Black Easily install third-party equipment, including those with traditional clamps, on a compatible trolling motor with this standard, round-nosed cone. Includes a transducer kit to remove, replace, or upgrade a built-in Garmin transducer. It’s recommended to replace all O-rings and compression seals when removing or replacing built-in transducers so that the motor returns to its original factory waterproof sealing. Specifications: Color: Black Nose Cone Type: Round  Includes Transducer Replacement Part: Force® Compatible Devices: Force® Kraken trolling motor Force® trolling motor

Force™ GT Nose Cone with Transducer Mount - Black Replace the standard part of your compatible trolling motor, or use the nose cone to install a compatible Garmin GT model transducer, including GT22, GT24, GT52 and GT54. If you’re rerouting a new transducer through the trolling motor shaft, the transducer replacement kit is recommended. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Force™ Round Nose Cone with Transducer Mount - Black Replace the standard part of your compatible trolling motor or use the nose cone when mounting equipment with traditional clamps. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Force® Kraken Transducer Replacement Kit Easily remove, replace, or upgrade the built-in Garmin transducer on a compatible trolling motor with this kit. It’s recommended to replace all O-rings and compression seals so the motor returns to its original factory waterproof sealing. The nose cone is not included. Specifications: Color: Black Includes Transducer Replacement Part: Force® Kraken Compatible Devices: Force® Kraken trolling motor

Force™ Trolling Motor Transducer Replacement Kit This kit contains everything you need to replace your built-in Garmin transducer. What's in the Box? Compression seal wrench No transducer compression seal 8-pin transducer compression seal 12-pin transducer compression seal Replacement o-ring kit Replacement stainless steel screws Compatible Devices: Force™ Trolling Motor WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Force® Kraken Nose Cone - Large - Black Replace the standard part of compatible trolling motors or use the nose cone to install a compatible Garmin GT model transducer, including the GT22, GT24, GT52, GT54, and GT56. If rerouting a new transducer through the trolling motor shaft, the transducer replacement kit is recommended. Specifications: Color: Black Nose Cone Type: Large Transducer Mount Includes Transducer Replacement Part: None Compatible Devices: Force® Kraken trolling motor Force® trolling motor

As the Fall months creep into our calendars, boat owners in cooler climates acknowledge, with sadness, that it’s time to put the boat away. Outside Storage? It’s a thought and an option but consider that you may be threatened by snow build up, tornadoes or hurricanes. The success of storing your boat outside depends on how well your boat is protected from the conditions outdoors.                          Rinse/Flush Rinsing the outside of your boat and trailer thoroughly with fresh water will remove excess salt. Pay particular attention to your trailer’s leaf springs, wheel hubs and brakes that are constantly submerged during launching and retrieval of your boat. Flush your engine's cooling system with fresh water in line with your engine manufacturer’s salt removal recommendations. This will minimize corrosion and overheating issues come spring. Drain your boat of all water – bilge, head, sink lines, water tanks, sea-cocks, and pipes. If you are in an area with extended periods of freezing, put antifreeze in the low parts if there is still some water present. Salt Watch out for salt. Buy a good salt remover to minimize corrosion. Add fuel stabilizer to top off your fuel tanks. Here is one recommended by CLR Marine. Diesel Formula Fuel Stabilizer & Performance Improver - 32oz *Case of 4* STA-BIL Diesel Formula Fuel Stabilizer is a diesel additive that keeps fuel fresh for quick, easy starts and maximized for engine performance. Designed for use with all diesel engines, and all diesel fuels, Sta-Bil Fuel Stabilizer Diesel formula prevents sludge and sediment formation, cleans and lubricates fuel injectors to improve performance and helps remove water. It is safe to use and recommended for use at every fill up, with the 32 ounce bottle treating up to 320 gallons of fuel. Batteries Remove the batteries from your boat and store in your garage or basement. Batteries should be connected to a battery charger that will give them a good charge and one that w automatically switches to a float/trickle charge to keep your batteries topped up. Match your charger to the type of battery you are charging. Using a charger manufactured for lead acid batteries to charge an AGM (absorbent glass mat) battery will cause damage to the battery. If you choose to keep your batteries in the boat, connect a solar trickle charger. These chargers will keep your batteries topped off without the hassle of removing heavy batteries from your boat. Cleaning Clean the exterior with the proper fiber glass or wood cleaner needed for your boat. Bright work can be cleaned by removing the wood or cleaning it as it is - installed. Be careful to not get the wood cleaner onto the deck surfaces. The exterior should be dried with a chamois cloth. Vinyl seat cushions and backs should be cleaned with vinyl cleaner. Hard surfaces inside the vessel can be wiped with all purpose cleaners. End your cleaning with a coat of wax to the exterior and polish. Don’t forget the bottom paint. Before you store, spend the time to give your boat a thorough cleaning. CLR Marine has many products by trusted brands such as Powerhouse, Davis Instruments, Jabsco, Shurhold, and Swobbit, to help winterize and clean. You will be grateful in the spring during launch time that your boat is already clean as the new boating season begins. Cover Up If you store outside in your yard, driveway, or a boat yard, a boat cover is a must to prevent damage from winter conditions. Leaving your boat in the water is not recommended. The boat is exposed to rough weather, and has a greater possibility of sinking if you aren’t monitoring it often. https://www.clrmarine.com/462m4/boat-outfitting/winter-covers.html and https://www.clrmarine.com/462m4/winterizing.html Circle May 21, 2022, on your calendar. The date is almost ten days before Memorial Day, next year when most harbors open for the season. Start your prep work, tune-ups, sanding, and painting to get out on the water and a great boating season. In the meantime, during the cold winter months, cozy up to the fire and read your boating manuals, new safety regulations and weather information. Fair winds and smooth sailing.   To obtain more information about the products and services mentioned in this article, please get in touch with CLR Marine https://www.clrmarine.com/. _________________________________________________________________________ Award-winning author Cheryl Kuba has been at the helm for more than 30 years sailing the Great Lakes, with side trips to the British Virgin Islands and St. Maarten. She has served as past- Commodore of Great Lakes Fleet 21 -Chicago region. 3happycampers.com ©Copyright Cheryl Kuba, 3happycampers.com, 2021.  

Force Round Nose Cone - White Easily install third-party equipment, including those with traditional clamps, on a compatible trolling motor with this standard, round nose cone. Specifications: Color: White Nose Cone Type: Round  Includes Transducer Replacement Part: None Compatible Devices: Force® Kraken trolling motor Force® trolling motor

  IN STOCK! Garmin Force™ Freshwater Trolling Motors & Accessories   Garmin's Force™ Freshwater Trolling Motors and accessories are now in stock. Garmin brings aboard the most powerful and most efficient trolling motor available. Check it out today!     Move your fishing to a higher level with force. The Force trolling motor is the most powerful and most efficient trolling motor available. Wireless chartplotter connectivity provides navigation, autopilot and anchor lock features. Use the precise anchor lock to hold your boat in the same location while you fish. Force includes a convenient wireless foot pedal that provides instant control and responsiveness yet feels and steers like a cable-steered pedal. See more fish and structure clearly with integrated Ultra High-Definition scanning sonar. It also includes a handheld remote control with a built-in sunlight-readable display. The remote gives you complete control of the trolling motor and simple point-and-go gesture steering.       Specials    Closeouts   Remanufactured    Rebates

G-Force ELIMINATOR Black Prop Nut for Garmin Force Trolling Motor One of the latest products in the G-Force lineup is the ELIMINATOR Prop Nut. The ELIMINATOR Prop Nut is built to make your trolling motor perform better, longer, and quieter.  Designed to lessen prop noise and vibration, The ELIMINATOR Prop Nut stabilizes the prop by providing a larger contact point. In addition, it acts as a heat sink and has built-in cooling ports that reduce the operating temperature for a longer battery and trolling motor life.  Made to fit Garmin Force trolling motors. This specific part comes in a black color to provide a sleek, matching aesthetic. Factory nut and washer will have to be removed prior to installing Eliminator, also if you have an anode it will have to be removed as well to use the Eliminator. Make sure that you're getting the most out of your trolling motor with the ELIMINATOR Prop Nut. Key ELIMINATOR Benefits: Machined from 6061 Billet Aluminum O-ring dampens noise/vibration and secures the nut Wider contact area for a more stable prop Cooling ports aid in heat dissipation Anodized protected No tools needed Available in popular colors Visually appealing Designed and made in the U.S.A. Patent pending

STRIKER™ 4 FishFinder with 4-Pin, 77/200kHz TM Transducer 3.5-inch CHIRP Fishfinder with GPS Features: Easy-to-use 3.5-inch color fishfinder with built-in, high-sensitivity GPS Find fish; mark and return to hot spots, docks and ramps Convenient keypad operation Includes CHIRP (77/200 kHz) sonar transducer; transmit power (200 W RMS)/(1,600 W peak-to-peak) Upgrade to high performance CHIRP with a GT8 or GT15 transducer (each sold separately) Finding fish is easier than ever with STRIKER 4 fishfinder. Mark and return to your hot spots, boat ramps and docks, and share your favorite waypoints and routes with other STRIKER and echoMAP™ combos. Smooth Scaling™ graphics provide uninterrupted imagery when switching between depth-range scales. Sonar history rewind allows you to scroll back through sonar images to mark waypoints you originally may have missed. Plus, it has a built-in flasher and displays speed data. Includes tilt/swivel mount, CHIRP (77/200 kHz) transducer with transom and trolling motor mounting hardware and cable. For high-performance CHIRP, purchase a GT8 or GT15 transducer (each sold separately). Experience the Clarity of CHIRP STRIKER 4 fishfinder includes a Garmin CHIRP (77/200 kHz) transducer, which provides a visibly higher level of clarity and detail for fish and structure than traditional 77/200 kHz transducers. Instead of sending just 1 single frequency, CHIRP sends a continuous sweep of frequencies, ranging from low to high, then interprets them individually upon their return. Since the frequencies provide a wider range of information, CHIRP sonar technology can create crisper fish arches with greater target separation. You also can upgrade to high-performance Garmin CHIRP technology, which provides crystal-clear sonar images with even more remarkable target separation and resolution from shallow to deeper depths. For better fishing, bottom contours are more visible, even at higher speeds, and signal noise can be suppressed at greater depths to provide a more timely interpretation of what's below. Mark Spots with High-Sensitivity GPS Unlike regular fishfinders, STRIKER fishfinders have built-in, high-sensitivity GPS to locate your current position quickly and precisely, then maintain your GPS location anywhere you go on the lake. More importantly, they allow you to mark spots where the fish are biting so you can return to them again in the future. You also can mark docks, boat ramps and other locations on the lake. Just follow the path created on your screen to return to them whenever you wish. Navigate Easily with Waypoint Map Since the STRIKER fishfinder series includes high-sensitivity GPS, you can see your position in relation to waypoints you have marked. Use the waypoint map to easily view, mark and navigate to locations such as brush piles, stumps and docks. It's also a great tool for finding your way back to the boat ramp. Check Your Speed on Screen You can quickly and easily see your boat's speed on the screen of your STRIKER fishfinder. It's a great tool to make sure you are trolling at the right speed for the lure you're using and for a particular fish species. It's also a good way to tell if you are going the right speed in wake-controlled areas. Fish Vertically with Built-in Flasher STRIKER provides you with both a fishfinder and flasher all in 1 unit. Anytime you are stationary fishing, such as ice fishing or jigging for crappie, the built-in flasher will show you the bottom, whether it is solid or muddy, your jig or weighted bait, and the depth of fish as they swim into the sonar beam. You can even watch how high your jig is being lifted and dropped and whether fish move toward or away from it. Take Your Fishfinder Anywhere A portable kit is available to protect and carry your STRIKER fishfinder with GPS, so it's perfect for kayak, canoe or ice fishing. It includes a sealed, rechargeable battery with charger, built-in transducer cable management and storage and suction cup transducer mount and float. In The Box STRIKER 4 Dual-beam transducer Transom and trolling motor mounts Tilt/swivel mount Power cable Documentation Connections Transducer pin numbers: 4 Pin WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Rain Collector Cone & Heater f/AeroCone - *Not For Use With Classic Rain Cone Rain collector cone and heater replacement kit Vantage Pro2 rain collectors with AeroCone. Heats ice and snow to keep your rain collector from freezing. All Vantage Pro2 stations come with the AeroCone. Unfortunately, the heater will not fit inside the AeroCone. This kit includes the heater and the larger old style cone to replace the AeroCone for those freezing winters that bring snow and ice. Keep snow from filling your Vantage Pro2 rain collector with this heater. Great for use in cold climates to measure freezing rain or the moisture content of snowfall. The heater warms the inside of the cone during cold weather. A thermostat switch turns the power off when temperatures rise and back on when they fall. Note: The heater must be plugged into an electrical outlet. Heater is not compatible with AeroCone; it is only compatible with the old style, larger rain cones. Specifications: Capable of melting liquid snow at a rate of 1/4" (6mm) of liquid precipitation per hour Warms only the inside of the rain collector and the cone itself Off/On switch allows you to turn heater on when you expect freezing conditions, and turn it off again when weather warms When turned on, the themostat switch turns power off if temperature reaches 110°F (43°C), and turns it back on with temperature drops to about 85°F (30°C) Cable length can be extended to 120' (36M) with two-twisted pair wire; further with single pair cable Replacement kit for stations with AeroCone rain cones Includes: Old style rain cone, bird spikes, and debris screen 24W, 24V Thermal cut-off switch Control unit Insulating reflective blanket AC-power adapter 50' (15M) cable Requires: Vantage Pro2 sensor suite or compatible stand-alone rain collector Must be plugged into an electrical outlet

Poly-Flex II Styled-to-Fit Boat Cover for 10.5' Blunt Nose Inflatable Boats - Grey *66" Max Beam Width Better known as “semi-custom” covers, Styled-to-Fit boat covers are our best selling, most popular category of covers and for good reason. Value. Our Styled-to-Fit boat covers are designed to accommodate all popular hull styles and boat configurations. For example, a 21' V-Hull Runabout boat cover will fit a 21' V-Hull Runabout Sea Ray, Bayliner, Four Winns, Stingray, etc. The cover is not “custom” to the specific boat, but a highly fitted cover designed to accommodate the primary characteristics of the boat style. Our Styled-to-Fit boat covers are great for travel*, mooring and storage, and feature: 1/4″ strong & durable shock cord encased into hem for a snug fit Motor covers are sewn into outboard model boat covers. Some designs come with a separate motor cover *Trailerable boat covers must be properly installed and tied down. From Pontoon Boats to Tournament Ski Boats, Jon Boats to Center Console Fishing Boats, Carver has a Styled-to-Fit boat cover that’s right for you! Poly-Flex II Good Quality Economically-priced 5.3 oz. Solution-Dyed Marine Polyester with urethane coating. Lightweight and strong. Good resistance to tearing. Durable water repellency, UV and mildew resistant finish. Breathable to help allow interior moisture to escape. Designed and sewn in the USA. (3 Year Limited Warranty). Features: Construction - Join seams are folded four-ply. No raw edges  Stitching - Double stitch construction for added strength and durability  Weather Resistant - Anti-wick thread throughout construction  Double Reinforced - Tie-down loops sewn into hem  Best Warranty in the Business - Best Warranty in the business based on fabric selection All Carver Covers are Made in the USA

Poly-Flex II Styled-to-Fit Boat Cover for 11.5' Blunt Nose Inflatable Boats - Grey *68" Max Beam Width Better known as “semi-custom” covers, Styled-to-Fit boat covers are our best selling, most popular category of covers and for good reason. Value. Our Styled-to-Fit boat covers are designed to accommodate all popular hull styles and boat configurations. For example, a 21' V-Hull Runabout boat cover will fit a 21' V-Hull Runabout Sea Ray, Bayliner, Four Winns, Stingray, etc. The cover is not “custom” to the specific boat, but a highly fitted cover designed to accommodate the primary characteristics of the boat style. Our Styled-to-Fit boat covers are great for travel*, mooring and storage, and feature: 1/4″ strong & durable shock cord encased into hem for a snug fit Motor covers are sewn into outboard model boat covers. Some designs come with a separate motor cover *Trailerable boat covers must be properly installed and tied down. From Pontoon Boats to Tournament Ski Boats, Jon Boats to Center Console Fishing Boats, Carver has a Styled-to-Fit boat cover that’s right for you! Poly-Flex II Good Quality Economically-priced 5.3 oz. Solution-Dyed Marine Polyester with urethane coating. Lightweight and strong. Good resistance to tearing. Durable water repellency, UV and mildew resistant finish. Breathable to help allow interior moisture to escape. Designed and sewn in the USA. (3 Year Limited Warranty). Features: Construction - Join seams are folded four-ply. No raw edges  Stitching - Double stitch construction for added strength and durability  Weather Resistant - Anti-wick thread throughout construction  Double Reinforced - Tie-down loops sewn into hem  Best Warranty in the Business - Best Warranty in the business based on fabric selection All Carver Covers are Made in the USA

Poly-Flex II Styled-to-Fit Boat Cover for 12.5' Blunt Nose Inflatable Boats - Grey *70" Max Beam Width Better known as “semi-custom” covers, Styled-to-Fit boat covers are our best selling, most popular category of covers and for good reason. Value. Our Styled-to-Fit boat covers are designed to accommodate all popular hull styles and boat configurations. For example, a 21' V-Hull Runabout boat cover will fit a 21' V-Hull Runabout Sea Ray, Bayliner, Four Winns, Stingray, etc. The cover is not “custom” to the specific boat, but a highly fitted cover designed to accommodate the primary characteristics of the boat style. Our Styled-to-Fit boat covers are great for travel*, mooring and storage, and feature: 1/4″ strong & durable shock cord encased into hem for a snug fit Motor covers are sewn into outboard model boat covers. Some designs come with a separate motor cover *Trailerable boat covers must be properly installed and tied down. From Pontoon Boats to Tournament Ski Boats, Jon Boats to Center Console Fishing Boats, Carver has a Styled-to-Fit boat cover that’s right for you! Poly-Flex II Good Quality Economically-priced 5.3 oz. Solution-Dyed Marine Polyester with urethane coating. Lightweight and strong. Good resistance to tearing. Durable water repellency, UV and mildew resistant finish. Breathable to help allow interior moisture to escape. Designed and sewn in the USA. (3 Year Limited Warranty). Features: Construction - Join seams are folded four-ply. No raw edges  Stitching - Double stitch construction for added strength and durability  Weather Resistant - Anti-wick thread throughout construction  Double Reinforced - Tie-down loops sewn into hem  Best Warranty in the Business - Best Warranty in the business based on fabric selection All Carver Covers are Made in the USA