Manufactured from high-density polyethylene with UV inhibitors. Meets low permeation standards to satisfy EPA/CARB regulations, USCG and ABYC standards. Seamless one-piece construction with reserve fuel area designed into tank by means of a partitioned bottom. When gauge registers empty, simply tilt the tank to access reserve fuel supply. Features 90° fuel withdrawal assembly that rotates 360° to reduce fuel line kinks. Direct sight fuel gauge with glass lens, 2-stage self-venting fuel cap required by EPA/CARB.

PP4600-00 PowerPod Uncut (Usable Face = 11.375"W x 6.75"H) (28.9cm W x 17.1cm H) PowerPods are designed for the serious boater who is blasting offshore. He demands the most from his boat and his electronics. He needs a tough and rugged mount to protect vital electronics from the harshest of offshore boating conditions. Sturdy and secure, yet clean and attractive, PowerPods are better than bracket mounting. Over 70 Pre-Cut PowerPods are available for all popular manufacturers products. 1.8" opening in the swivel tube provides plenty of room for running wires and connectors through. PowerPods are positioned at a 20 degree tilt back veiwing angle. PowerPods for Sail are for mounting on a flat surface. Perhaps under the dodger or aft end of the cockpit table especially on boats with dual wheels. Structural Rigidity The Gen3 enhancements now include a thicker gauge Acrylic Capped ABS material that improves strength and provides better structural rigidity. This thicker material allows for a larger waterproof seal. The better the structural rigidity, the less flexing when tightening and more uniform pressure on the seal. The excellent UV stability of the Acrylic is combined with the durability of the ABS. The Acrylic cap protects the ABS from UV and it's potentially damaging effects on plastic. These NavPods are really strong! Waterproof Seal All NavPods are manufactured with a double gasket system providing an excellent watertight seal between the front and back of the NavPod. This seal provides the best protection of your Marine Electronics. NavPods are made to withstand the harshest wet offshore boating conditions. Gen3 enhancements include a thicker external silicone gasket with improved flush fit. The internal Poran Microcell Polyurathane gasket is now 50% thicker and is not subject to "compression set" like many rubber compounds. This is important when you need to open the NavPod in the future in order to service your electronics. The gasket will continue to do its job. Nickel Chrome Plated Stainless Steel NavPod uses all 316 stainless steel hardware that is supplied with each NavPod. Large round head tamperproof screws have deeper sockets for the NavPod wrench for better holding ability when tightening than screws used on our Traditional Series NavPod. For Gen3 NavPods we provide nickel chrome-plated stainless steel tamperproof screws for security combined with a little bling! Commitment to Quality We are committed to producing high quality Waterproof Housings for Marine Electronics. We stand behind our commitment by offering a 10-year warranty on all new Gen3 NavPods. We want you to be a NavPod customer for life and are willing to earn your trust and loyalty.

PP5100 PowerPod Uncut (Usable Face = 14"W x 7.625"H) (35.5cm W x 19.4cm H) PowerPods are designed for the serious boater who is blasting offshore. He demands the most from his boat and his electronics. He needs a tough and rugged mount to protect vital electronics from the harshest of offshore boating conditions. Sturdy and secure, yet clean and attractive, PowerPods are better than bracket mounting. Over 70 Pre-Cut PowerPods are available for all popular manufacturers products. 1.8" opening in the swivel tube provides plenty of room for running wires and connectors through. PowerPods are positioned at a 20 degree tilt back viewing angle. PowerPods for Sail are for mounting on a flat surface. Perhaps under the dodger or aft end of the cockpit table especially on boats with dual wheels. Structural Rigidity The Gen3 enhancements now include a thicker gauge Acrylic Capped ABS material that improves strength and provides better structural rigidity. This thicker material allows for a larger waterproof seal. The better the structural rigidity, the less flexing when tightening and more uniform pressure on the seal. The excellent UV stability of the Acrylic is combined with the durability of the ABS. The Acrylic cap protects the ABS from UV and it's potentially damaging effects on plastic. These NavPods are really strong! Waterproof Seal All NavPods are manufactured with a double gasket system providing an excellent watertight seal between the front and back of the NavPod. This seal provides the best protection of your Marine Electronics. NavPods are made to withstand the harshest wet offshore boating conditions. Gen3 enhancements include a thicker external silicone gasket with improved flush fit. The internal Poran Microcell Polyurathane gasket is now 50% thicker and is not subject to "compression set" like many rubber compounds. This is important when you need to open the NavPod in the future in order to service your electronics. The gasket will continue to do its job.  Nickel Chrome Plated Stainless Steel NavPod uses all 316 stainless steel hardware that is supplied with each NavPod. Large round head tamperproof screws have deeper sockets for the NavPod wrench for better holding ability when tightening than screws used on our Traditional Series NavPod. For Gen3 NavPods we provide nickel chrome-plated stainless steel tamperproof screws for security combined with a little bling! Commitment to Quality We are committed to producing high quality Waterproof Housings for Marine Electronics. We stand behind our commitment by offering a 10-year warranty on all new Gen3 NavPods. We want you to be a NavPod customer for life and are willing to earn your trust and loyalty.

PP5100 PowerPod Uncut (Usable Face = 14"W X X 7.625"H) (35.5cm W X 19.4cm H) - Carbon Black PowerPods are designed for the serious boater who is blasting offshore. He demands the most from his boat and his electronics. He needs a tough and rugged mount to protect vital electronics from the harshest of offshore boating conditions. Sturdy and secure, yet clean and attractive, PowerPods are better than bracket mounting. Over 70 Pre-Cut PowerPods are available for all popular manufacturers products. 1.8" opening in the swivel tube provides plenty of room for running wires and connectors through. PowerPods are positioned at a 20 degree tilt back viewing angle. PowerPods for Sail are for mounting on a flat surface. Perhaps under the dodger or aft end of the cockpit table especially on boats with dual wheels. Structural Rigidity The Gen3 enhancements now include a thicker gauge Acrylic Capped ABS material that improves strength and provides better structural rigidity. This thicker material allows for a larger waterproof seal. The better the structural rigidity, the less flexing when tightening and more uniform pressure on the seal. The excellent UV stability of the Acrylic is combined with the durability of the ABS. The Acrylic cap protects the ABS from UV and it's potentially damaging effects on plastic. These NavPods are really strong! Waterproof Seal All NavPods are manufactured with a double gasket system providing an excellent watertight seal between the front and back of the NavPod. This seal provides the best protection of your Marine Electronics. NavPods are made to withstand the harshest wet offshore boating conditions. Gen3 enhancements include a thicker external silicone gasket with improved flush fit. The internal Poran Microcell Polyurathane gasket is now 50% thicker and is not subject to "compression set" like many rubber compounds. This is important when you need to open the NavPod in the future in order to service your electronics. The gasket will continue to do its job.  Nickel Chrome Plated Stainless Steel NavPod uses all 316 stainless steel hardware that is supplied with each NavPod. Large round head tamperproof screws have deeper sockets for the NavPod wrench for better holding ability when tightening than screws used on our Traditional Series NavPod. For Gen3 NavPods we provide nickel chrome-plated stainless steel tamperproof screws for security combined with a little bling! Commitment to Quality We are committed to producing high quality Waterproof Housings for Marine Electronics. We stand behind our commitment by offering a 10-year warranty on all new Gen3 NavPods. We want you to be a NavPod customer for life and are willing to earn your trust and loyalty.

PED4600-00 PedestalPod Uncut (Usable Face = 11.375"W x 6.75"H) (28.9cm W x 17.1cm H) - Carbon Black PedestalPods are better than bracket mounting. Very sturdy and secure, yet clean and attractive, this mount provides protection of your fishfinder/chartplotter from the harshest of wet boating conditions. PedestalPods provide the convenience of easily reaching and controlling the fishfinder/chartplotter while providing added security with protection from theft. PedestalPods position your fishfinder/chartplotter at 20" off the deck and located near the bow and at the 45° angle for ease of viewing while fishing. This allows the user to easily reach and access the fishfinder/chartplotter for changes to range, zoom or even control the trolling motor. PedestalPods are manufactured with a double gasket system that provides an excellent watertight seal keeping spray off the electrical connections on the back of your fishfinder/chartplotter assuring reliability and longevity of your marine electronics. Your fishfinder/chartplotter is easily flush mounted into the pre-cut face of the NavPod. The heavy duty, powder coated aluminum pedestal tube is 3” in diameter with a 5” round base and has a large 1.75” opening providing plenty of room for running wires and connectors internally for a very clean look and provides protection for wires and electrical connectors from water intrusion, UV exposure or damage from just getting kicked or snagged and ripped out of their sockets. NavPods come with a security wrench and nickel chrome-plated stainless steel tamperproof screws for protection from theft. There are pre-cut models available for 7", 9" and 12" LCD displays from all major marine electronic manufacturers.

PED5100 PedestalPod Uncut (Usable Face = 14"W x 7.625") (35.5cm W x 19.4cm H) - Carbon Black PedestalPods are better than bracket mounting. Very sturdy and secure, yet clean and attractive, this mount provides protection of your fishfinder/chartplotter from the harshest of wet boating conditions. PedestalPods provide the convenience of easily reaching and controlling the fishfinder/chartplotter while providing added security with protection from theft. PedestalPods position your fishfinder/chartplotter at 20" off the deck and located near the bow and at the 45° angle for ease of viewing while fishing. This allows the user to easily reach and access the fishfinder/chartplotter for changes to range, zoom or even control the trolling motor. PedestalPods are manufactured with a double gasket system that provides an excellent watertight seal keeping spray off the electrical connections on the back of your fishfinder/chartplotter assuring reliability and longevity of your marine electronics. Your fishfinder/chartplotter is easily flush mounted into the pre-cut face of the NavPod. The heavy duty, powder coated aluminum pedestal tube is 3” in diameter with a 5” round base and has a large 1.75” opening providing plenty of room for running wires and connectors internally for a very clean look and provides protection for wires and electrical connectors from water intrusion, UV exposure or damage from just getting kicked or snagged and ripped out of their sockets. NavPods come with a security wrench and nickel chrome-plated stainless steel tamperproof screws for protection from theft. There are pre-cut models available for 7", 9" and 12" LCD displays from all major marine electronic manufacturers.

RMX4600 RailMount Uncut (Usable Face = 11.375"W x 6.75"H) (28.9cm W x 17.1cm H) RailMount NavPods are best used for mounting of an autopilot control, sailing instrument, or small chartplotter onto an existing pedestal guard. Fits onto any 1" or 1.25" diameter tube. A Chromed Stainless Steel arm is used to mount a NavPod. The NavPod can rotate 180 degrees for easy viewing while sitting under the dodger on a rainy day. All wire run from the NavPod, down the center of the stainless steel arm, and into the pedestal guard. This application provides a clean and sturdy installation for electronics, without replacement of the pedestal guard. All RailMounts Include: Acrylic capped ABS plastic Chromed stainless steel tamper-proof fasteners Double Seal for watertight integrity Models are available pre-cut for popular electronics Chromed stainless steel arm with swivel mount Two sets of adaptors included for 1" or 1.25" diameter tubing The Hi-Gloss Material NavPods are manufactured with a custom co-extruded acrylic capped ABS material. We use the absolute best UV resistant material that provides a very high gloss white finish that matches gel-coated fiberglass. The Gen3 enhancements now include a thicker gauge material that improves strength and provides for better structural rigidity. The Waterproof Seal All NavPods are manufactured with a double gasket system providing an excellent watertight seal between the front and back of the NavPod for protection of your Marine Electronics. NavPods are made to withstand the harshest of wet offshore boating conditions. Gen3 enhancements include a thicker external silicone gasket with improved flush fit. The internal EPDM gasket is now 50% thicker and is not subject to "compression set" like many rubber compounds. This is important when you need to open the NavPod in the future to service your electronics. The Nickel Chrome Plated Screws We use all stainless steel mounting hardware that is supplied with each NavPod. Large round head tamperproof screws have deeper sockets for the NavPod wrench for better holding ability when tightening than the previous screws. For Gen3 we provide nickel chrome-plated stainless steel tamperproof screws for security combined with a little bling! The Manufacturing Process Heavy-gauge thermoforming is considered an art since many processes come into play. It all starts with the design and development of the tooling. We are fortunate to have experienced in-house design engineers who utilize CAD programs like Solidworks, Catia and AutoCad. Surfcam is used to interface with our CNC machining centers to produce quality tools with precision tolerances. We have re-designed and re-tooled all of the popular NavPods. We have reviewed all of the former products and selected the best design elements of each and incorporated them in every new Gen3 product. Our Commitment to Quality We are committed to producing the best possible waterproof housing for Marine Electronics. Now with two decades of experience under our belt, we are confident you will have years of trouble free service and a long lasting high gloss finish. We will stand behind our commitment by now offering a 10-year warranty on all new Gen3 NavPods.

High density low permeation tanks meet or exceed EPA/CARB regulations. Lightweight with sturdy handles for easy transport and built-in fuel reserve capacity. Non-corrosive, unbreakable, dent-resistant, with UV stabilized, guaranteed no-leak construction. Includes 2-stage CARB compliant fuel cap.

High density low permeation tanks meet or exceed EPA/CARB regulations. Lightweight with sturdy handles for easy transport and built-in fuel reserve capacity. Non-corrosive, unbreakable, dent-resistant, with UV stabilized, guaranteed no-leak construction. Includes 2-stage CARB compliant fuel cap.

High density low permeation tanks meet or exceed EPA/CARB regulations. Lightweight with sturdy handles for easy transport and built-in fuel reserve capacity. Non-corrosive, unbreakable, dent-resistant, with UV stabilized, guaranteed no-leak construction. Includes 2-stage CARB compliant fuel cap.

Manufactured from high-density polyethylene with UV inhibitors. Meets low permeation standards to satisfy EPA/CARB regulations, USCG and ABYC standards. Seamless one-piece construction with reserve fuel area designed into tank by means of a partitioned bottom. When gauge registers empty, simply tilt the tank to access reserve fuel supply. Features 90° fuel withdrawal assembly that rotates 360° to reduce fuel line kinks. Direct sight fuel gauge with glass lens, 2-stage self-venting fuel cap required by EPA/CARB.

High density low permeation tanks meet or exceed EPA/CARB regulations. Lightweight with sturdy handles for easy transport and built-in fuel reserve capacity. Non-corrosive, unbreakable, dent-resistant, with UV stabilized, guaranteed no-leak construction. Includes 2-stage CARB compliant fuel cap.

Water tank sizes ensures you the right fit for your boat. The resin used in Moeller each water tank meets FDA specs for polymers used in contact with food, which ensures safe, odor-free water. A multitude of water/waste tank sizes ensures you the right fit for your vessel needs. Feature nominal wall thickness of 0.300. Resin meets FDA spec CTF177 1520 requirements. Satisfies all U.S. Coast Guard standards. Provides standard NPT openings for vent, fill & drain. Polyethylene tanks will not filter taste into water or emit waste odors. DROP SHIPPED DIRECT FROM FACTORY, FREIGHT NOT ALLOWED. EXTENDED LEAD TIME MAY APPLY.

Water tank sizes ensures you the right fit for your boat. The resin used in Moeller each water tank meets FDA specs for polymers used in contact with food, which ensures safe, odor-free water. A multitude of water/waste tank sizes ensures you the right fit for your vessel needs. Feature nominal wall thickness of 0.300. Resin meets FDA spec CTF177 1520 requirements. Satisfies all U.S. Coast Guard standards. Provides standard NPT openings for vent, fill & drain. Polyethylene tanks will not filter taste into water or emit waste odors. DROP SHIPPED DIRECT FROM FACTORY, FREIGHT NOT ALLOWED. EXTENDED LEAD TIME MAY APPLY.

Sierra serpentine belts water pumps and alternators on Mercruiser inboard/outdrive.