Yamaha Fuel Line Kit 6' x 3/8" Attwood's low-permeation fuel line kits set the standard in performance, safety, and value. Along with featuring Attwood's award-winning Universal Sprayless Connector, these kits meet strict United States EPA regulations. Attwood Corporation has been an award-winning leader in engineering, testing, and manufacturing the highest quality marine products for over 100 years. We deliver safe and reliable lighting, fuel systems, water systems, seating & pedestals, swim ladders, custom upholstery, and general marine accessories that are easy to install and meet regulatory compliance. Features: Includes Attwood's award-winning Universal Sprayless Connector; no more dangerous fuel sprays when connecting and disconnecting pressurized lines Multi-layer low-permeation primer bulb with 60% more fuel output compared to competitors Includes 3/8-inch low-permeation fuel hose that resists kinking and hardening; rated up to 100 degrees Centigrade Versatile: compatible with Ethanol blended fuels, Yamaha Brand engines and tanks Attwood products are both compatible and reliable, engineered and built with a never-fail attitude WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Mercury/Yamaha Female Hose Engine Fitting - 3/8" Barb Connect your tank and fuel lines with confidence; the solid machined-brass construction holds up to leaded, unleaded, and alcohol-based fuels for. Features: Solid machined brass for dependable performance, peace of mind Hose female  Tank or Engine End Replaces Yamaha 6Y1-24305-03 *Specifically mates to Attwood part number: 8897-6

Universal Brass Fuel Hose Fitting - 1/4" NPT x 3/8" Barb  This Attwood Fuel Tank Fitting is a dependable replacement for original equipment and provides a sure connection in a fuel line. Features: Fitting is suitable for use with leaded, unleaded, ethanol-blended, and alcohol-blended fuels Material Construction: Brass Male thread, hose barb (inch) Male 1/4" NPT x 3/8" Barb  *Use thread sealant on all threads

Universal Aluminum Fuel Hose Fitting - 3/8" NPT x 3/8" Barb This Attwood Fuel Tank Fitting is a dependable replacement for original equipment and provides a sure connection in a fuel line. Features: Fitting is suitable for use with leaded, unleaded, ethanol-blended, and alcohol-blended fuels Specifications: Material Construction: Aluminum Male thread, hose barb (inch) Male 3/8" NPT x 3/8" Barb  *Use thread sealant on all threads

Aluminum Fuel Hose Fitting - 1/4" NPT x 3/8" Barb - (Anti-Siphon Valve) This Attwood Fuel Tank Fitting is a dependable replacement for original equipment and provides a sure connection in a fuel line. This is a male thread, anti-siphon valve with ¼-In. NPT x 3/8-In. barb. Features: Fitting is suitable for use with leaded, unleaded, ethanol-blended, and alcohol-blended fuels Anti-Siphon Valve Material Construction: Aluminum Male thread, hose barb (inch) Male 1/4" NPT x 3/8" Barb  *Use thread sealant on all threads

Aluminum Fuel Hose Fitting - 3/8" NPT x 3/8" Barb - (Anti-Siphon Valve) This Attwood Fuel Tank Fitting is a dependable replacement for original equipment and provides a sure connection in a fuel line. This is a male thread, anti-siphon valve with 3/8-In. NPT x 3/8-In. barb.  Features: Fitting is suitable for use with leaded, unleaded, ethanol-blended, and alcohol-blended fuels Anti-Siphon Valve Material Construction: Aluminum Male thread, hose barb (inch) Male 3/8" NPT x 3/8" Barb  *Use thread sealant on all threads

Premium Impeller Kit 65 x 15.8 x 68mm - 10 Blade - Spline Insert Replaces JMP 7420-01, Jabsco 31130-0061. Specifications: Weight: 0.244 kg Dimensions: 65 mm x 15.8 mm x 68 mm Type: Copolymer Neoprene Original MC Blend Certification: ISO 9001 Quality Guaranteed

Premium Impeller Kit 65 x 15.8 x 41.5mm - 12 Blade - Key Insert Replaces JMP 7300-01, Jabsco 18948-0001, Johnson Pump 09-702B-1, Sherwood 10615K. Specifications: Weight: 0.178 kg Dimensions: 65 mm x 15.8 mm x 41.5 mm Type: Copolymer Neoprene Original MC Blend Certification: ISO 9001 Quality Guaranteed

Premium Impeller Kit 65 x 15.8 x 51mm - 12 Blade - Key Insert Replaces JMP 7352-01, Jabsco 18327-0001, Sherwood 15000K. Specifications: Weight: 0.185 kg Dimensions: 65 mm x 15.8 mm x 51 mm Type: Copolymer Neoprene Original MC Blend Certification: ISO 9001 Quality Guaranteed

T-Top Boat Shade Kit - 6' x 5'  An economical and versatile way to add shade to the rear of your center console or walk around boat. Our light weight material, "Resilience" has exceptional elasticity and protects against harmful UV rays while reflecting up to 75% of UV heat. Installs within minutes. Kit includes necessary poles and stores easily in it's own bag. Available in 3 sizes. Features & Benefits: RESILIENCE shades are specifically designed for UV-protection and to handle harsh marine environments. RESILIENCE is bonded with an outer UV reflective coating. At 20% stretch, it offers an effective UV block of 98% and it will reflect up to 75% of UV heat. RESILIENCE elasticity allows it to fit many size boats, which gives it a custom fit appearance. RESILIENCE is extremely breathable and whisper quiet while underway and it can handle speeds up to 30 knots. Because of dark pigments, it holds up to UV rays the longest and provides the most UV protection. RESILIENCE has a one year warranty. Shade color: BLACK T-Top Boat Cover's RESILIENCE shades' qualities and features make this the best product available for sun protection anywhere! Size (width x length): 5' x 6' Stretch (width x length): 7' x 8'

Flojet 01740-003S Strainer 3/8" Barb X 3/8" Barb Flojet Strainer with 3/8” Hose Barb Inlet and 3/8” Hose Barb Outlet, In-Line Design, Fine 40 Mesh Stainless Steel Screen   Strainers for In-Line Applications. FDA Approved for Potable / Drinking Water.   Strainer Body made of Polypropylene with Clear Polysulfane Cap and Buna-N FDA O-Rings. Suitable for Fresh or Salt Water use. Easily Cleaned with See Through Thread-On Cap.   Course 20 Mesh Screens are typically used for Washdown, Bilge and Toilet Rinse Applications. Fine 40 Mesh Screens are typically used for Potable / Drinking Water Applications.   Maximum Flow Rates: With 3/4" Hose Barb Fittings: 7.0 GPM (27 LPM) With 1/2" Hose Barb Fittings: 4.0 GPM (15 LPM) With 3/8" Hose Barb Fittings: 2.1 GPM (8 LPM)   Maximum Water Temperature: 160F (70C) Maximum Pressure: 70 PSI (5 bar)   The Strainers that are Equiped with a "Direct Plug-In Quad Port" will fit into the Snap-In Quad Ports on Flojet Diaphragm Pumps and Jabsco Diaphragm Pumps sized under 6 GPM.

2104 PowerBar 600AMP Cable Connector 4 x 3/8 16 Stud Terminal Specifications: Max Voltage: 300 V AC/48 V DC Number of Terminal Studs: 4 Terminal Type: 3/8" - 16 Stud WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

2107 PowerBar 600AMP Cable Connector - 8 x 3/8" 16 Stud Terminal Specifications: Maximum Voltage: 300 V AC/48V DC Number of Terminal Studs: 8 Terminal Type: 3/8" - 16 Stud WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

March 1A-MD 3/8 Mag Drive Pump March Pump's industrial 1A-MD-3/8 is an American submersible seal-less centrifugal magnetic drive pump. It is capable of generating a maximum flow of 2.3 gallons per minute at 0.25 feet, and its maximum head is 4.5 Feet (or around 2PSI).  The 1A-MD-3/8 pump may be used submerged or not submerged. The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Buna N, Nylon, Carbon/Teflon, and Stainless Steel.  When submerged, Epoxy, Noryl, and the SJT Cord are also in contact with the solution. The inlet connection is 3/8 inch smooth, and the outlet is 3/8 inch smooth. The standard motor is a 1 Phase 115V or 230V 0.005 Horsepower motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheit or 160 Celsius in open air, or 87 Fahrenheit or 71 Celsius if submerged. The March 1A-MD-3/8 centrifugal magnetic drive pump is capable of handling fresh water, salt water, and mild chemicals.   Perfect for Applications Including Applications for the 1A-MD-3/8 Magnetic Drive Pump include chemical transfer, photographic processing equipment, refrigeration systems, and water displays.   Great for Chemicals Including The 1A-MD-3/8 has pumped Acetone, Ammonium Chloride, Ammonium Chloride, Ammonium Hydroxide, Citric Acid, Ethylene Glycol, Magnesium Nitrate, Potassium Carbonate, Sodium Borate, Fresh Water, Salt Water, and many more chemicals.  The 1A-MD-3/8 may have been modified to handle these chemicals.    Type: Centrifugal Mag Drive Inlet: 3/8"OD Outlet: 3/8"OD Wet End: Polypropylene (Front Housing, Rear Housing, Impeller), Buna N (O-Ring), Carbon/Teflon (Thrust Washer), 316 Stainless Steel (Shaft) Uses: Submersible or Open Air When submerged, the following is also in contact with the solution, Epoxy, Noryl, SJT Cord    

Applications for the March AC-1A-MD-3/8 Magnetic Drive Pump include photographic processing equipment, refrigeration systems, and water displays.   The AC-1A-MD-3/8 Part # 0115-0064-0300 has pumped Acetone, Ammonium Chloride, Ammonium Chloride, Ammonium Hydroxide, Citric Acid, Ethylene Glycol, Magnesium Nitrate, Potassium Carbonate, Sodium Borate, Fresh Water, Salt Water, and many more chemicals.  The AC-1A-MD-3/8 may have been modified to handle these chemicals.    March Pump's industrial AC-1A-MD-3/8 is an American seal-less centrifugal magnetic drive pump ideal for applications such as chemical recirculation and chemical transfer. It is capable of generating a maximum flow of 2.3 gallons per minute at 0.25 feet, and its maximum head is 4.6 Feet (or around 2PSI). The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Buna N, Nylon, Carbon/Teflon, Stainless Steel, and Ceramic Magnet. The inlet connection is 0.375 inch smooth, and the outlet is 0.375 inch smooth. The standard motor is a 1 Phase 115V or 230V 0.05 Horsepower motor, which can be run on 60 hertz on 115V or 50 and 60 hertz on 230V (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheit or 87 Celsius. The March AC-1A-MD-3/8 centrifugal magnetic drive pump is capable of handling mildly or highly corrosive chemicals, acids, and solvents.     Unit System 60Hz 50Hz Max Flow 2.3 GPM 8.7 LPM Max Head 4.6 FT 1 M Power .005 HP .003 KW Electrical 115V 60HZ      230V 50/60HZ   Type Centrifugal Mag Drive Inlet 3/8"OD Outlet 3/8"OD Wet End Polypropylene (Front and Rear Housing), Buna N (O-Ring), Nylon (Impeller), Carbon/Teflon (Thrust Washer), 316 Stainless Steel (Shaft), Ceramic Magnet     Part # 0115-0064-0300