|
HRC 10-8 Horizontal Windlass 5/16" Chain, 5/8" Rope, 12V, with Capstan
Designed for boats up to 45 feet, the HRC10-8 Horizontal Series windlasses proudly follow in the highly successful footsteps of Maxwell's previous, fully automatic rope / chain anchor winches.
Kit Includes
Windlass
On/Off Breaker Panel
Reversing Solenoid
Up/down Panel Switch
Clutch Release Handle
Features
The HRC10-8 is Maxwell's fully automatic rope/ chain or all chain horizontal windlass
Designed to effortlessly retrieve and deploy 8mm (5/16" ) chain and 16mm (5/8" ) three strand or 8-brait (plait) rope.
The HRC 10-8 has a patented uniquely designed chain wheel will accommodate ANY 5/16" or 8 mm marine grade chain spliced to 5/8" rope.
The aesthetically pleasing above deck design, evolved from the philosophy of form follows function, encapsulates the motor and drive in a two part watertight case, saving space below deck
Case Material: Anodized Aluminum
The two part case consists of a die cast, marine-grade hard anodised alloy front section and a rugged and easily removable composite motor cover aft section.
This two piece watertight case allows for quick and easy, on-deck,routine maintenance.
Simple " bolt down" installation ensures effortless and rapid on-deck installation and set up.
The stainless steel pressure arm always exerts maximum control pressure on the rode (rope, splice or chain).
The new and revolutionary patented Wave Design chainwheel is able to accommodate a wide range of chain pitch differences, within the specified chain size diameters, suitable for use with the HRC10 Series.
The unique Maxwell " wrap around" horizontal chainwheel ensures that more than 90x of the wheel is used, allowing greatly improved rope and chain handling compared with competitor designs.
High quality Stainless Steel chainwheels
The HRC10 works just as effectively with all-chain rodes for those who desire the added security and holding power of an all-chain anchor system.
The integral chain pipe and huge, through deck hawse pipe throat ensures easy entry of the rope / chain rode into and out of the anchor locker.
Cone type clutch/brake mechanism permits manual, "free fall" anchoring and emergency crank recovery of the rode and anchor if required.
The sealed oil bath and marine-grade hard anodised, alloy gearbox provides high efficiency output drive via precision worm and wormwheel.
Exclusive Maxwell 3 YEAR Limited Warranty
Specifications
Maximum PUll: 1540 lbs
Chain Short Link: 5/16" or 8mm
Chain Speed (Anchor Retrieval): 79 ft per Minute
Rope Speed (Anchor Retrieval): 65 ft per Minute
Rope Size (Nylon 3 strand or 8 Plait): 5/8"
Power Supply (DC): 12VDC
Motor Power: 1000 Watts
Net weight: 42 lbs
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
2213.51 |
|
|
VWC1000 Windlass 5/16" - 3B Chain
The VWC Series of windlasses is designed for automatic (hands-free) handling of chain-only anchor rodes. They have an integral chainpipe and chain stripper built into the windlass body to facilitate jam-free operation, and automatic delivery of the chain to and from the chain locker.
VWC windlasses are available in two formats — a low profile, chainwheel-only version, and one with an added independent capstan for the retrieval of a secondary mostly rope rode, or to assist with docking procedures.
This entries features the chainwheel with capstan version of the VWC. The vertical capstan on VWC windlasses is ideal for multi-use rope hauling as, unlike horizontal capstans, it can handle lines leading from any direction.
Features:
Voltage: 12V
Chain Size & Type: 5/16", 3B
|
2503.48 |
|
|
The all new compact HRC6 and HRC8 are Maxwell's horizontal versions of the latest innovative new vertical RC6 and RC8 automatic rope/chain windlasses. The new HRC6 and HRC8 are packed with original and proven features including rode management technology developed by Maxwell.
HRC8
Simple "bolt down" installation ensures effortless and rapid on-deck installation and set up
Guaranteed trouble free rode transition from rope to chain, by means of an innovative, proven and patented pressure arm system, within a safe enclosed design
Integrated composite nylon, through deck hawse pipe for ease of installation and smooth, snag-free operation
High efficiency spur gearbox incorporating a robust non-backwind mechanism
High speed, jam-free retrieval of rope and chain controlled from a remote panel mounted Up/Down switch
Emergency "free fall" function in the event of onboard power failure
Revolutionary new chainwheel - see over
Heavy duty, dual direction motor incorporating new technology features, including integrated wiring for quick electrical installation, is easily removed for simple routine electric brush maintenance
Now incorporating Maxwell's automatic free-fall technology. Simply activate the windlass 'free fall' lever, operate your down control (helm station or footswitch) and the windlass will freefall your anchor. Ready to lift the anchor? Activate the up control and the 'free fall' device automatically disengages allowing you to power up your anchor
Aesthetically pleasing above deck design, encapsulating the motor and drive in a watertight case, saving space below deck and allowing simple routine maintenance
Die cast, marine-grade, alloy case is hard anodized for unsurpassed marine protection
Kits include:windlass, on/off breaker panel, reversing soleniod, up/down panel switch, a clutch release handle
Specifications:
Model: HRC8
Maximum Pull: 900lbs
Chain Short Link: 5/16"
Rope Size (Nylon): 9/16"
Line Speed(Anchor Retrieval): 108'/min
Power Supply(DC): 12V
Motor Power: 600W
Net Weight: 25lbs
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
1006.12 |
|
|
Levered Chain Stopper f/5/16" or 8mm Chain
Chain stoppers hold the chain and take the load off the windlass. They are used to set and ride on the anchor, break free the anchor or to prevent accidental free fall of the anchor while under way. Also recommended for VW series rope and chain systems to hold the chain while changing over from rope to chain.
8mm (5/16"):
B - 72mm (2-7/8")
C - 20mm (7/8")
F - 152mm (6")
G - 92mm (3-5/8")
G1 - 30mm (1-3/16")
I - 70mm (2-7/8")
J - 31.5mm (1-1/4")
J1 - 10mm (7/16")
K - 51.5mm (2-1/8")
L - 95mm (3-3/4")
M - M10
|
269.10 |
|
|
Economy Chain Stopper f/5/16", 3/8", 8mm & 10mm Chain
Chain stoppers hold the chain and take the load off the windlass. They are used to set and ride on the anchor, break free the anchor or to prevent accidental free fall of the anchor while under way. Also recommended for VW series rope and chain systems to hold the chain while changing over from rope to chain.
8/10mm (5/16"/3/8"):
B - 62mm (2-3/8")
C - 6mm (1/4")
F - 80mm (3-1/8")
G - 46mm (1-4/4")
G1 - 17mm (5/8")
I - 92mm (3-5/8")
J - N/A
J1 - 37mm (1-1/2")
K - 74mm (2-7/8")
L - N/A
M - M10
|
81.36 |
|
|
RC10-8 Capstan 12V Windlass - 5/16" Chain & 5/8" Rope
The stainless steel (AISI 316) RC10 Series rope/chain windlass is part of Maxwell’s upper mid-range line-up and is suitable for boats ranging from 9m (30ft) to 14m (48ft). The RC10-8 is a second-generation rope/chain windlass and is a favorite choice for cruising yachts, launches, pilothouse vessels, and light commercial operators. The intentionally simple design yields excellent longevity and performance figures and has contributed to a well-earned reputation for reliability.
The patented Wave Design™ rope/chain gypsy (chain wheel) is able to accommodate a wide range of chain pitch differences (both imperial and metric) within the RC10’s specified chain size diameters.
Features:
Works just as effectively with all-chain rode
The gearbox can be removed by hand and without tools for easy maintenance and inspection
Full disassembly capability of the top works utilizing only the handle provided and an Allen key
Manual override and ‘Free Fall’, using the emergency crank/clutch handle provided
Sealed oil bath and marine-grade hard anodized, alloy gearbox provides maximum output via a precision worm and worm wheel
Every Maxwell RC10 automatic rope/chain windlass comes with top works, motor/gearbox and dual-direction solenoid
The unique spacer tube design allows for installation through virtually any deck thickness, and the multiple mounting positions and self-aligning gearbox ensure optimal orientation in virtually all installation situations
Specifications:
Maximum Pull: 1540 lbs. (700 kg)
Static Hold: 3300 lbs. (1500 kg)
Chain Size: 5/16 in. (8 mm)
Rope Size (Nylon): 9/16 in. – 5/18 in. (14 mm – 16 mm)
Chain Speed (Anchor Retrieval): 79 ft/min (24 m/min)
Rope Speed (Anchor Retrieval): 65 ft/min (20 m/min)
Power Supply (DC): 12 VDC
Motor (Watt): 1000 W
Net Weight: 42 lbs (19 kg)
Hydraulic Pressure: 2000 PSI (138 Bar)
Hydraulic Flow: 5.3 USgal/min (20 l/min)
Net Weight (Hydraulic): 42 lbs (14 kg)
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
2271.18 |
|
|
Single-Hook Anchor Chain Tensioner for 5/16" Chain
These fittings will securely tension and hold the anchor in the bow roller channel. They will free up use of the bow cleat and prepare the anchor for sea condition assuring you peace of mind. This fitting is not designed to take the strain of the rode of a boat at anchor. "Single Hook" style has overall length of 12", the threaded hook has 1-1/2" of adjustment for ease of installation.
|
105.34 |
|
|
Chain Grip for 5/16" (8mm) Chain
Perfect to ensure safe anchoring by easing the tension on the anchor chain. Protects the boat by reducing the chafe of the chain on the rub rail and roller chock. Positioned between two links of the chain (single-handed operation). Optimized design to avoid accidental release of the chain.
Features:
One-piece with nonmoving parts
Forged in Duplex stainless steel grade (increased mechanical & corrosion resistance)
Made in France
Rope size: 22 mm
Specifications:
Chain diameter: 8 mm (5/16")
Rope diameter: 17 mm (5/8")
Working load: 480 kg (1,050 lbs)
Breaking load: 890 kg (1,960 lbs)
Weight: 88 g (0.194 lbs)
Length: 85 mm ( 3-11/32")
Applications:
Mouillage
|
43.02 |
|
|
12-10 AWG Heat Shrink Ring Terminal - 5/16" Stud Size - 3 Pack
Ring terminals are used to connect wires to a connection point. They can easily be used with two or more wires. They offer a solid connection as the ring is fitted over a stud. This removes the possibility of the terminal disconnecting. Using the proper parts is essential to a high-quality electrical connection. Ring terminals are the most secure type of tongue-style terminal. They are known for their durability and ease of use.
Features:
Tinned copper
600 Volts
The operating temperature is -55°C to 125°C
Highly compliant
Benefits & Protections:
Solid connections
Extremely durable
Long-lasting
Tin-plated
Easy to install
Specifications:
Color: Yellow
Wire AWG: 12-10 AWG
Stud Size (inch): 5/16"
Terminal Pad Width (inch): 0.54”
Package Size: Three included
|
3.02 |
|
|
12-10 AWG Heat Shrink Ring Terminal - 5/16" Stud Size - 25 Pack
Ring terminals are used to connect wires to a connection point. They can easily be used with two or more wires. They offer a solid connection as the ring is fitted over a stud. This removes the possibility of the terminal disconnecting. Using the proper parts is essential to a high-quality electrical connection. Ring terminals are the most secure type of tongue-style terminal. They are known for their durability and ease of use.
Features:
Tinned copper
600 Volts
The operating temperature is -55°C to 125°C
Highly compliant
Benefits & Protections:
Solid connections
Extremely durable
Long-lasting
Tin-plated
Easy to install
Specifications:
Color: Yellow
Wire AWG: 12-10 AWG
Stud Size (inch): 5/16"
Terminal Pad Width (inch): 0.54”
Package Size: Twenty-five included
|
23.65 |
|
|
12-10 AWG Heat Shrink Ring Terminal - 5/16" Stud Size - 100 Pack
Ring terminals are used to connect wires to a connection point. They can easily be used with two or more wires. They offer a solid connection as the ring is fitted over a stud. This removes the possibility of the terminal disconnecting. Using the proper parts is essential to a high-quality electrical connection. Ring terminals are the most secure type of tongue-style terminal. They are known for their durability and ease of use.
Features:
Tinned copper
600 Volts
The operating temperature is -55°C to 125°C
Highly compliant
Benefits & Protections:
Solid connections
Extremely durable
Long-lasting
Tin-plated
Easy to install
Specifications:
Color: Yellow
Wire AWG: 12-10 AWG
Stud Size (inch): 5/16"
Terminal Pad Width (inch): 0.54”
Package Size: One-hundred included
|
48.35 |
|
|
RC8-8 Windlass with Capstain - 12V - 5/16" Chain to 9/16" or 5/8" Rope
RC Rope/Chain Series
Maxwell's RC series windlasses proudly follow in the highly successful footsteps of the Freedom, Liberty and HRC fully automatic rope/chain anchor winches. RC10 and RC8 are available in both capstan and low profile versions. RC6 is available in low profile version only.
The RC12 Series incorporates Maxwell's latest stylish innovation in automatic rope/chain technology. Retaining the classic open design styling more appropriate on larger boats, the RC12 Series represents the next generation of rope/chain windlass evolution in every respect.
Every Maxwell automatic rope/chain windlass is available with all the necessary components for fully automatic dual direction control in a competitively priced package.
Maxwell’s Revolutionary Chainwheel
Maxwell once again leads the market in innovative thinking with the introduction of their latest Wave Design™ chainwheel. This patented rope/chain wheel incorporates two unique design concepts that greatly improve the handling and control of the rope/chain spliced rode. The outer ribs of the chainwheel are angled slightly forward ensuring that the rope and the chain are smoothly guided in the wheel during anchor retrieval.
As the rope pulls into the wheel, the opposite facing inner ribs grip the rope in an undulating manner, securing the rope more firmly in a 'wave pattern' action that is far superior to the traditional 'jam cleat' manner of holding the rope compared to all other products on the market. Not only does this Wave Design™ hold the rope more securely, it is also kinder on the rope resulting in increased longevity of your anchor rode.
Wave Design™ Chainwheel
Maxwell once again leads the market in innovative thinking with the introduction of their latest Wave Design™ chainwheel.
This rope/chain wheel incorporates two unique design concepts that greatly improve the handling and control of the rope/chain spliced rode. The outer ribs of the chainwheel are angled slightly forward ensuring that the rope and the chain are smoothly guided in the wheel during anchor retrieval.
As the rope pulls into the wheel, the opposite facing inner ribs grip the rope in an undulating manner, securing the rope more fi rmly in a ‘wave pattern’ action that is far superior to the traditional ‘jam cleat’ manner ofholding the rope. Not only does this Wave Design™ hold the rope more securely, it is also kinder on the rope resulting in increased longevity of your anchor rode.
Is fitted to the RC Series and the HRC Series windlasses, designed for anchor rodes with any marine grade chain, G4, BBB, Proof Coil and Metric.
Features:
The larger stainless steel RC8-8 can be used with 8mm (5/16 inch) chain spliced to 14mm (9/16 inch) three strand or 8-plait rope.
The ingeniously designed rope/chain gypsy (chainwheel) is able to accommodate a wide range of chain pitch differences within the specified chain size diameters suitable for use with the RC8 Series.
A sleek, Low Profile version and a MAX-grip capstan drum version, with drum made in chromed bronze, are available.
Simple two piece installation saves time and money and allows easy retrofitting without disassembly of the windlass.
Unique spacer tube design allows installation through virtually any deck thickness and the multiple mounting positions and self aligning gearbox ensure optimal location of gearbox and motor in virtually all installation situations.
The RC8 features Maxwell's revolutionary Wave Design chainwheel.
The heavy duty stainless steel pressure arm is designed to effectively help grasp the rope/chain splice, giving the RC8 an unparalleled level of performance. In combination with a heavy duty, large wire diameter, stainless steel pre-loaded spring, the pressure arm always exerts maximum control pressure.
The RC8 works just as effectively with all-chain rodes.
Huge, through deck hawse pipe throat ensures easy entry of the rope/chain rode into and out of the anchor locker.
Full disassembly capability of the topworks utilising only the handle provided and an Allen key.
Manual override and Free Fall, using the emergency crank/clutch handle provided.
Sealed oil bath and marine-grade hard anodised, alloy gearbox provides maximum output via a precision worm and worm wheel.
|
1701.31 |
|
|
RC12-10 12V Windlass EDC - 3/8" Chain & 3/4" Rope
The RC12-10 automatic rope/chain windlass is built to effortlessly retrieve and deploy a 3/8 in. short link chain and 5/8" to 3/4 in. 8-Plait rope using Maxwell’s patented Wave Design™ chain wheel.
The RC12 is a highly versatile windlass offering multiple configurations (anti-clockwise, capstan, low profile, extended deck clearance, etc.) and is packed with patented features showcasing the very best of Maxwell engineering. The RC12 windlass range is suitable for boats ranging from 10m (30ft) to 20m (65ft) and has been designed and engineered to expertly balance aesthetics with rugged dependability.
The deck plate, chain pipe cover, heavy-duty pressure arm, stripper arm, chain wheel, and fluted capstan drum are all manufactured using marine-grade (AISI 316) stainless steel, which is x-rayed by Maxwell QC to ensure the chemical composition of the metal.
The through-deck hawse pipe ensures easy entry of the rope/chain rode into and out of the anchor locker, and the double cone-type brake/clutch mechanism permits ‘Free Fall’ anchoring. Cone clutches, unlike dog clutches, provide smooth progressive engagement, ensuring safe and precise operator control.
Emergency manual retrieval is made simple and easy with Maxwell’s unique "Active Latch Ratchet System" operation that prevents the backwind of the windlass during manual hauling of the anchor.
Features:
Activation of the ratcheted mechanism lever ensures the windlass cannot backwind during emergency (manual) retrieval of the rode (rope and/or chain) and anchor
The Gearbox Used on the RC12 Provides Several Advantages, Including:
Fast and easy windlass installation
More corrosion resistant
Easy to maintain and service
Takes up less room in the anchor locker
75:1 ratio, single stage design with fewer moving parts, for smoother and quieter operation
Allows for multi-positioning of the gearbox/motor
Specifications:
Maximum Pull: 2500 lbs. (1134 kg)
Static Hold: 4840 lbs. (2200 kg)
Chain Size: 3/8 in. (10/11 mm)
Rope Size (Nylon): 5/8 in. – 3/4 in. (16 mm – 20 mm)
Chain Speed (at normal working load): 79 ft/min (24 m/min)
Rope Speed (at normal working load): 65 ft/min (20 m/min)
Power Supply (DC): 12 VDC
Motor (Watt): 1200 W
Net Weight: lbs (32 kg)
Hydraulic Pressure: 2000 PSI (138 Bar)
Hydraulic Flow: 11 USgal/min (40 l/min)
Net Weight (Hydraulic): 71 lbs (32 kg)
Important: Maxwell windlasses must be used in conjunction with a chain stopper and/or alternative snubbing device to take the load off the windlass while laying at anchor. The chain stopper and alternative snubbing system should also be used to secure the anchor in the fully raised position while underway.
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
3244.43 |
|
|
RC10 Automatic Rope/Chain Windlass
Designed for 5/16" chain and 5/8" rope combination
Maximum pull: 1540 lbs
Metric Chain Size: 8mm
Motor Wattage: 1000W
Innovative heavy duty stainless steel pressure arm, coupled with a unique rope/chain gypsy, giving an unparalleled level of performance.
Simple two piece installation, saving time and money and allowing easy retrofitting without disassembly of the windlass.
Manufactured from marine grade chromed bronze for long term durability
The topworks can be fully disassembled utilizing the handle provided, a screw driver and common allen key, making regular service and maintenance a breeze. No special tools required!
A huge, through deck, hawse pipe throat ensures easy entry of the rope/chain rode into and out of the anchor locker
Not only does the RC10 effortlessly handle combination rope/chain rodes, it works just as well with all chain rodes for those who may want the extra security of an all chain systems combined with an elegantly styled, low profile windlass on their foredeck.
Exclusive Maxwell 3 Year Limited Warranty ensuring your confidence that you are getting the best product on the market.
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
2074.37 |
|
|
Anchor Rode - 18'-5/16" Chain to 200'-5/8" Nylon Brait
18' of 5/16" HT spliced chain to 200' of 5/8" Nylon Brait rope
Nylon Brait™ is an 8-strand nylon rope created through braid technology that yields a product with a firm strand formation yet full stowage flexibility. The unique construction offers maximum strength and
energy absorption, and working windlass grip-hold.
Applications: Docklines and anchorlines
Construction: 8-strand Nylon
Specific Gravity: 1.14
|
501.84 |
|