Quick T6315 is a non-reversing contactor that is able to operate electric motors for windlasses and capstans. Due to the external connections, this unit is very easy to install. The casing of this unit is IP66 waterproof. This unit is sold complete with the solenoid unit and product sheet. For use with 700, 1000, 1400, 1500, 1700 Watt Motors, 12V.

Reversing Solenoid Pack - 12V Maxwell Reversing Solenoid Pack 12V, replaces P19045.

T6415-12 Reversing Solenoid 12V Unit for Windlass Motors The Quick T6415 is a reversing contactor that is able to operate electric motors for windlasses and capstans. Due to the external connections, this unit is very easy to install. The casing of this unit is IP66 waterproof. This unit is sold complete with the solenoid unit and product sheet.

Intermittent Duty Reversing Solenoid - 12V DPDT A combination of two solenoids in one package to reduce cost and maximize space savings while also providing simpler wiring. Two integral solenoids provide dynamic braking for permanent magnet motors when neither coil is energized. This intermittent duty solenoid can be used at a variety of amperages.  Specifications: 75A Make/Break: 5 min On, 5 min Off 125A Make/Break: 30 sec On, 5 min Off 150A Make Break: 0.5 sec On, 5 min Off Circuitry: DPDT Contact Material: Copper Housing: Plastic

75A Motor Reversing Solenoid Two solenoids in one saves money and simplifies wiring. Provides braking dynamic capability for permanent magnet motors when coils are not energized. Features: Rated at 75A make and break at 12V DPDT intermittent duty Comparable to Cole Hersee part number 24450 WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Reversing Solenoid Pack - 24V Maxwell Reversing Solenoid Pack 24V, replaces P19046.

Hydraulic Power Unit 12V with Deutch Connector A compact powerhouse that creates hydraulic pressure to lower and raise the trim tabs. It employs two solenoid valves to direct the flow of fluid to the actuators. The solenoid valves lock tightly to secure the tabs in place. Strength to lower and hold even the largest tabs in place. The Lexan cover provides water resistance to the electrohydraulic unit, and the translucent reservoir allows fluid check at a glance. The mounting bracket is sold separately (# H1179). HPU measures 4″ x 7 1/2″ x 5 1/2″. Uses automatic transmission fluid. Includes pump, solenoid valves, reservoir, and cover.  This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Anchoring & Docking Are you heading out on the water? Make sure you have a great boat anchor onboard. Having an anchor on standby is the easiest way to ensure you are safe. If your engine dies, you need an anchor to hold you in place while making repairs.  If you want to get out into the current, you need an anchor to keep you in place while fishing or swimming. We have the right anchor for your boat.   Your boat is not a bumper car. To protect your investment and keep your boat looking good, make sure you have boat fenders. When it comes to docking, the risk of rubbing or bumping increases unless you are prepared to prevent it Choose from our wide range of fenders and dock bumpers to ensure your boat is docked safely without a single scratch.

Commercial Duty Reversing Vane Pump - 12V GROCO  Vane Pumps are self-priming, are instantly reversible, and are capable of operation in either direction. Relatively high flow (more than gear pumps) makes them suitable for general purpose duties such as deck-wash, bilge pumping (filtered inlet),  fuel transfer, ballast transfer, and oil change.  Ignition protected motor, #316 stainless steel shaft, and reversing (R). SPO-80 Series Vane Pumps have a more powerful motor and are better suited for long run-time or head pressure greater than 20 PSI.  Specifications: Self Priming: YES Thread NPT: 1/2" + Garden Hose Adaptor Control Type: Pump Mounted Reversing Switch Max GPM: 7 Breaker DC: 30 Amp

Heavy Duty Positive Displacement Reversing Vane Pump - 12V GROCO Vane Pumps are self-priming, are instantly reversible, and are capable of operation in either direction. Relatively high flow (more than gear pumps) makes them suitable for general purpose duties such as deck-wash, bilge pumping (filtered inlet),  fuel transfer, ballast transfer, and oil change.  All models have an ignition protected motor and #316 stainless steel shaft. Specifications: Self Priming: YES Thread NPT: 1/2" + Garden Hose Adaptor Control Type: Pump Mounted Reversing Switch Max GPM: 6.5 Breaker DC: 30 Amp

PM Solenoid Pack - 12V Maxwell's PM Solenoid Pack that is 12V. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Solenoid Switch - 12V 12V solenoid for the BOW50/55/60/75 bowthrusters

Solenoid Valve - 12V 12V Electric Valve to be used with centralized fresh water system.  Features: Certification: CE marked 94/25/ECC, ISO8846 Small Craft, Electromagnetic compatibility 89/336/EEC, EN51014 1993/radio disturbance

Continuous Duty Solenoid - 200A - 12V Relays are commonly referred to as remote-acting switches and Littelfuse manufacturers a broad range of styles to meet your application. To ensure you are utilizing the proper remote-acting switches, review the attributes in the specifications tab below against your application requirements. Specifications: Current Rating (Continuous) in Amps: 200 Circuitry: SPST Normal Position: Normally Open Contact Material: Silver Housing: Plated Steel

HRC 10-8 Horizontal Windlass 5/16" Chain, 5/8" Rope, 12V, with Capstan Designed for boats up to 45 feet, the HRC10-8 Horizontal Series windlasses proudly follow in the highly successful footsteps of Maxwell's previous, fully automatic rope / chain anchor winches. Kit Includes Windlass On/Off Breaker Panel Reversing Solenoid Up/down Panel Switch Clutch Release Handle Features The HRC10-8 is Maxwell's fully automatic rope/ chain or all chain horizontal windlass Designed to effortlessly retrieve and deploy 8mm (5/16" ) chain and 16mm (5/8" ) three strand or 8-brait (plait) rope. The HRC 10-8 has a patented uniquely designed chain wheel will accommodate ANY 5/16" or 8 mm marine grade chain spliced to 5/8" rope. The aesthetically pleasing above deck design, evolved from the philosophy of form follows function, encapsulates the motor and drive in a two part watertight case, saving space below deck Case Material: Anodized Aluminum The two part case consists of a die cast, marine-grade hard anodised alloy front section and a rugged and easily removable composite motor cover aft section. This two piece watertight case allows for quick and easy, on-deck,routine maintenance. Simple " bolt down" installation ensures effortless and rapid on-deck installation and set up. The stainless steel pressure arm always exerts maximum control pressure on the rode (rope, splice or chain). The new and revolutionary patented Wave Design chainwheel is able to accommodate a wide range of chain pitch differences, within the specified chain size diameters, suitable for use with the HRC10 Series. The unique Maxwell " wrap around" horizontal chainwheel ensures that more than 90x of the wheel is used, allowing greatly improved rope and chain handling compared with competitor designs. High quality Stainless Steel chainwheels The HRC10 works just as effectively with all-chain rodes for those who desire the added security and holding power of an all-chain anchor system. The integral chain pipe and huge, through deck hawse pipe throat ensures easy entry of the rope / chain rode into and out of the anchor locker. Cone type clutch/brake mechanism permits manual, "free fall" anchoring and emergency crank recovery of the rode and anchor if required. The sealed oil bath and marine-grade hard anodised, alloy gearbox provides high efficiency output drive via precision worm and wormwheel. Exclusive Maxwell 3 YEAR Limited Warranty Specifications Maximum PUll: 1540 lbs Chain Short Link: 5/16" or 8mm Chain Speed (Anchor Retrieval): 79 ft per Minute Rope Speed (Anchor Retrieval): 65 ft per Minute Rope Size (Nylon 3 strand or 8 Plait): 5/8" Power Supply (DC): 12VDC Motor Power: 1000 Watts Net weight: 42 lbs This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.