|
|
|
|
Safety First when it comes to Trailer Lighting
Safety is important, not only on the water, but on the road going to and coming from the water. If your trailer is more than a few years old, most likely you have had or are having some issues with the lights and the electrical system on your trailer. Fortunately, most issues are pretty easy to fix.
The first thing to do is to test the lights by hooking up to the vehicle harness and checking all lights to make sure they are bright and working. If any are dim or not functioning, connect a tester to the vehicle harness to see if there might be an issue with the electrical source. Cleaning the connectors of the harness on both the vehicle and trailer side is critical, and can easily be done with a can of electrical connector spray and a fine wire brush. Also, clean the ground contact and tighten the ground wire.
Make sure to check the ground screw and replace it if it is corroded. Most bulbs are easily replaceable by simply twisting them to remove and install them. You can also clean up corroded sockets by gently sanding away the corrosion with fine sandpaper. It's possible you may have to replace wiring, which can be purchased as part of a complete kit that includes new lights, connectors, and lenses.
We suggest if you do not have LED light on your trailer to switch over to them. Led lights are brighter, more efficient and has multiply bulbs so you will never have a taillight completely unlit if one bulb burns out.
CLR Marine carries trailer lights and lighting kits, which are complete with license plate holder, wiring and side lights. Along with any other trailer accessory you may need.
Specials Closeouts Remanufactured Rebates
|
|
|
Submersible LED Low-Profile Trailer Light Kit
Ideal replacement or upgrade for most trailers. Conforms to applicable U.S. FMVSS and Canadian CFMVSS standards.
Kit Includes:
Includes (2) multi-functional (stop/tail/turn) submersible low-profile LED trailer lights
License plate bracket
Wiring harness and installation hardware
|
45.72 |
|
|
ZCI™ Zero Contact Interface Universal Trailer Light Power Modulite® Wiring Kit
Wiring Kit for Installing #119146, #119147, #119176, #119177, #119179, #119180, #119190, #119192 ModuLite® Power Modules, Includes 20 ft. Undercar Wire, Fuse w/Holder and Attaching Terminals
Features:
Wiring kit for installing all Modulites
Includes 10 AMP fuse
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
19.46 |
|
|
Submersible Trailer Light Kit
Applicable to trailers under 80 inches wide. Ideal for utility, snowmobile, camping, motorcycle, and boat trailers. Design conforms to applicable US FMVSS and Canadian CMVSS safety standards.
Complete Kit Includes:
A pair of 8-function stop/tail/turn lights, wiring harness, and license plate bracket
|
19.50 |
|
|
Low-Profile Submersible Trailer Light Kit
Low profile for trailers over 80 inches wide. Ideal replacement lights for most boat trailers. Conforms to applicable U.S. FMVSS and Canadian CMVSS safety standards.
Kit Includes:
(2) multi-function lamps
Wiring harness
License plate bracket and mounting hardware
|
25.00 |
|
|
Submersible LED Trailer Light Kit
For use with trailers under 80 inches wide. Conforms to applicable U.S. FMVSS and Canadian CFMVSS standards.
Kit Includes:
(2) multi-functional (stop/tail/turn) submersible LED trailer lights
License plate bracket
Wiring harness and installation hardware
|
41.42 |
|
|
ZCI™ Zero Contact Interface Universal ModuLite® - Universal Trailer Light Power Module
ZCI sensor technology and direct connection to the tow vehicle battery, eliminates all electrical connection and interference with the tow vehicle electrical system. Vehicles with 12 volt system only.
Features:
NO CUTTING OR SPLICING VEHICLE WIRING!
Isolates Trailer Light Operation from Tow Vehicle's Electrical System
Works with 2 or 3 wire systems
Works with PWM or Multiplexed systems requiring 2 or 3 wire hookup
Rated for up to 4.2 amps for turn/stop & 7.5 amps for taillight trailer circuits
Works with low side switched vehicles
Integrated auto resetting short & overload protection
Robust design allows for interior or exterior mounting
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
211.04 |
|
|
2" Marine Spreader Light - Scene Optics - White Housing - Pro Series 3.0
READY FOR ANYTHING! This 2-inch marine LED scene spreader light is the perfect way to add lights to a vessel. The 2'' Single Row Scene Light throws light at a 120-degree beam angle, giving users extremely widespread dispersion without a hot spot, and is perfect for area lighting when boating or fishing at night. Whether users are tying knots, catching fish, or cleaning the boat, they will have all the light that is needed.
With the flick of a switch, users can see that this vehicle work light is built with quality parts. From the moment users put the 2-inch LED light bar Single Row series in their hands, it becomes completely clear how this vehicle work light can take the beating Black Oak's claim it can. This small light bar comes complete with a wiring pigtail, stainless steel brackets, and hardware—everything needed to mount and get going!
Black Oak has taken the LED game to the next level. The Pro Series 3.0 features top-of-the-line LED tech, boasting a 20% increase in lumens, making this series of lights one of the brightest on the market.
Features:
Scene optics
360° Ceramic Protection against UV, Salt Water & Corrosion
2 Stage Hydrex Seal Lock for IP69 protection and a fully submersible light bar
Heavy-duty Dynamax housing for a 4x stronger frame
Activities & Uses:
Deck or spreader lights
Trailer lighting
Rear bumper lights
Work lights
Mower lights
Golf cart lighting
Technical Specifications:
Total Wattage: 20W
Amp. Draw: 1.4
LED Quantity: 2
Weight: 0.7 lbs.
Raw Lumens: 1560
Warranty: Lifetime
IP Rating: IP69K
Dimensions (Width x Height x Depth): 2.82" x 1.91" x 2.18”
In the Box:
2" marine spreader light
(1) Wiring pigtail with deutsch connector
All hardware, ready to install!
*Sold as an Individual
|
88.20 |
|
|
ModuLite® HD Protector with Integrated Circuit & Overload Protection & 5-Flat Connector for Backup Light or Surge Brake Lockout Circuit
Features:
The unit is rated for up to 4.2 amps for Turns/Stops circuits and 7.5 amps for the Taillight circuit and 4.2 amps for Back-Up circuit
Draws power directly from the vehicle battery and uses less than 5mA of the vehicle circuit for sensing to turn the trailer functions on and off
Will work with either LED/Incandescent bulbs (vehicle & trailer)
Has integrated re-settable Short Circuit and Overload protection, to safeguard itself and the tow vehicle from shorts and installation wiring mishaps
Designed not to send feedback thru the vehicle circuits
The trailer brakes will override the hazard lamps when the brake is activated
The taillight circuit has been upgraded to work with vehicles that use a pulse width modulation (PWM), this will allow the converter to turn on fully and gives the trailer lights full brightness during activation
Will work with most vehicles that have a multiplex system for lighting
Will not work with vehicles with low-side switch
Integrated 5-flat electrical wiring connector. Fifth circuit added for surge brake lockout or backup light circuit on trailers (some units will come with a 5-way cap. Mounting bracket sold separately)
Can be used on a 2 wire or 3 wire system
All solid-state components in potted encapsulation
Includes integrated protective cover
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
73.75 |
|
|
2" LED Pod Light - Flood Optics - Black Housing - Pro Series 3.0
The Cree flood light pod by Black Oak LED offers two levels of power to fill any need users might possibly have. This CREE LED floodlight delivers extreme IP69K durability to match such high-performance LEDs, allowing users to have confidence that their lights are going to perform when needed.
Cree and Osram are the biggest names on the LED market for a reason. The Cree flood lights put out more light and more power at such an extreme level. Users won't believe that so much light came from an LED so tiny. These mount virtually anywhere, and with all the hardware needed in the box, this CREE LED floodlights is ready to go.
Black Oak has taken the LED game to the next level. The Pro Series 3.0 features top-of-the-line LED tech, boasting a 20% increase in lumens, making this series of lights one of the brightest on the market.
Features:
Flood lighting pattern
360° Ceramic Protection against UV, Salt Water & Corrosion
2 Stage Hydrex Seal Lock for IP69 protection and a fully submersible light bar
Heavy-duty Dynamax housing for a 4x stronger frame
Activities & Uses:
Fog light replacements
Bow light's on flats boats with trolling motor
Lower A-Pillar ditch lights on UTV's and trucks
Trailer lighting
Front bumper lights
Auxiliary motorcycle lights
Technical Specifications:
Total Wattage: 40W
Amp. Draw: 2.8
LED Quantity: 4
Weight: 1.4 lbs.
Raw Lumens: 3,120
Warranty: Lifetime
IP Rating: IP69K
Dimensions with Mounting Bracket (Width x Height): 3.20" x 3.80"
In the Box:
2” pod light with flood optics
Complete wiring harness with fuse, relay, and switch
Mounting brackets
All hardware, ready to install!
*Sold as an Individual
|
116.10 |
|
|
2" LED Pod Light - Spot Optics - Black Housing - Pro Series 3.0
This Cree spot light pod by Black Oak LED offers 40 watts of total power. Also, this CREE LED spotlight delivers extreme IP69K durability to match such high-performance LEDs, allowing users to have confidence that their lights are going to perform when needed.
Cree and Osram are the biggest names on the LED market for a reason. The Cree spot lights put out more light and more power at such an extreme level. Users won't believe that so much light came from an LED so tiny. These mount virtually anywhere, and with all the hardware needed in the box, these CREE LED spotlights are ready to go. This 40w Cree POD light is the perfect Jeep JK windshield lights, and Black Oak created a sick light kit for your off-roading adventures (sold separately).
Black Oak has taken the LED game to the next level. The Pro Series 3.0 features top-of-the-line LED tech, boasting a 20% increase in lumens, making this series of lights one of the brightest on the market.
Features:
Spot lighting pattern
360° Ceramic Protection against UV, Salt Water & Corrosion
2 Stage Hydrex Seal Lock for IP69 protection and a fully submersible light bar
Heavy-duty Dynamax housing for a 4x stronger frame
Activities & Uses:
Fog light replacements
Bow light's on duck boats with trolling motor
Lower A-Pillar ditch lights on UTV's and trucks
Trailer lighting
Front bumper lights
Auxiliary motorcycle lights
Technical Specifications:
Total Wattage: 40W
Amp. Draw: 2.8
LED Quantity: 4
Weight: 1.4 lbs.
Raw Lumens: 3,120
Warranty: Lifetime
IP Rating: IP69K
Dimensions with Mounting Bracket (Width x Height): 3.20" x 3.80"
In the Box:
2” pod light with spot optics
Complete wiring harness with fuse, relay, and switch
Mounting brackets
All hardware, ready to install!
*Sold as an Individual
|
116.10 |
|
|
2" Spreader Light - Scene Optics - Black Housing - Pro Series 3.0
READY FOR ANYTHING! This 2-inch LED light bar is barely even noticeable in a grill, mounted to a bumper, or all-terrain vehicles. This 2'' single-row scene light throws light at a 120-degree beam angle, giving users extremely widespread dispersion without a hot spot, and is perfect for reversing or area lighting.
With the flick of the switch, users can see that this vehicle work light is built with quality parts. From the moment anyone puts the 2-inch LED light bar Single Row series in their hand, it becomes completely clear how this vehicle work light can take the beating Black Oak claims it can. This small light bar comes complete with a wiring pigtail, stainless steel brackets, and hardware—everything users need to mount and get going!
Black Oak has taken the LED game to the next level. The Pro Series 3.0 features top-of-the-line LED tech, boasting a 20% increase in lumens, making this series of lights one of the brightest on the market.
Features:
Scene optics
360° Ceramic Protection against UV, Salt Water & Corrosion
2 Stage Hydrex Seal Lock for IP69 protection and a fully submersible light bar
Heavy-duty Dynamax housing for a 4x stronger frame
Activities & Uses:
Deck or spreader lights
Trailer lighting
Rear bumper lights
Work lights
Mower lights
Golf cart lighting
Technical Specifications:
Total Wattage: 20W
Amp. Draw: 1.4
LED Quantity: 2
Weight: 0.7 lbs.
Raw Lumens: 1560
Warranty: Lifetime
IP Rating: IP69K
Dimensions (Width x Height x Depth): 2.82" x 1.91" x 2.18”
In the Box:
Marine spreader light
Wiring pigtail with deutsch connector
All hardware, ready to install!
*Sold as an Individual
|
84.00 |
|
|
2" Marine Flush Mount Spreader Light - Black Housing - Pro Series 3.0
READY FOR ANYTHING! This 2-inch flush mount LED light bar is the perfect addition to any hardtop for the boater in need of deck lighting. The 2 inch black marine flush mount spreader light throws light at a 120 degree beam angle, giving users extremely widespread dispersion without a hot spot, and is perfect for area lighting when fishing at night or getting ready early in the morning.
With the flick of a switch, users can see that this marine spreader light is built with quality parts. From the moment users put this Black Oak 2 Inch Black Marine Flush Mount Spreader Light in their hand, it becomes completely clear how this spreader light can take the beating Black Oak claims it can. This small light bar comes complete with a wiring pigtail and everything needed to mount and get going!
Black Oak has taken the LED game to the next level. The Pro Series 3.0 features top-of-the-line LED tech, boasting a 20% increase in lumens, making this series of lights one of the brightest on the market.
Features:
Spreader light
360° Ceramic Protection against UV, Salt Water & Corrosion
2 Stage Hydrex Seal Lock for IP69 protection and a fully submersible light bar
Heavy-duty Dynamax housing for a 4x stronger frame
Activities & Uses:
Deck or spreader lights
Trailer lighting
Rear bumper lights
Work lights
Mower lights
Golf cart lighting
Technical Specifications:
Total Wattage: 20W
Amp. Draw: 1.4
LED Quantity: 2
Weight: 0.7 lbs.
Raw Lumens: 1560
Warranty: Lifetime
IP Rating: IP69K
Dimensions (Length x Height x Depth): 4-1/4" x 2-3/8" x 2-1/2”
Mounting Holes: 3-1/2” apart horizontally
In the Box:
2” marine black spreader light
Wiring pigtail with deutsch connector
All hardware, ready to install!
*Sold as an Individual
|
94.08 |
|
|
Blackout Cube LED Light *2-Pack
Heise’s Blackout Series high output cube LED lights are small but powerful for better coverage at night. These next-generation lights have refined frames and cleaner lines for a sleek yet minimalistic look. The upgraded optics have changed from a direct to an indirect placement allowing more control of the location and pattern of the beam. This allows the lights to be tailored to the vehicle, its entire lighting system, and for the driver’s lighting coverage needs. Each set is rated IP67 and includes a dual light wiring harness (HE-DLWH1) for installation. Flush mount options are also available and sold individually (without harness).
Features:
2 Light Pack
Input Voltage: 12-24V Dc
Color Temperature: 5700K
Beam Pattern: 10o Spot
Housing Material: Die-Cast Aluminum
Color: Black
Lens Material: Polycarbonate
Electronics: Integrated-Epoxy Encapsulated
Hardware: Stainless 316
Operating Temperature: -40°F To +140°F
Protection: Reverse Polarity
Mounting: Side & Rear
Limited Lifetime Warranty
Specifications:
Size: 2.5”
4 LEDs
Wattage: 20W
Raw Lumens: 1,920lm
Lux at 10m: 635
Current Consumption @ 13.8V: 1.3A
IP Rating: IP67
*Values are for a single light
Vehicle Applicatins:
Universal
*WARNING: THIS LIGHTING PRODUCT IS SOLD FOR OFF-ROAD USE ONLY. This product should not be used on the road. Owners should keep the original factory bulbs so that they can replace them for use on public roads. Keep the box that the new bulbs came in to store the bulbs and be sure to handle them with care when removing and re-installing.
|
136.56 |
|