BM100 Battery Monitoring Solution The BM100 is a complete system comprising SmartShunt and the veKonvert NMEA 2000 interface. It is part of Digital Yacht’s iSeaSense range of NMEA 2000 boat instruments. With this solution, your multi-function display becomes a sophisticated battery and energy management system. Features Digital Yacht’s BM100 battery monitoring system allows highly accurate DC voltage, current, and capacity measurements, enabling reliable monitoring of your boat’s battery and electrical system. Core to the system is the SmartShunt. It measures battery voltage and current. Based on these measurements, it intelligently calculates the battery’s state of charge and the time to depletion for the remaining charge. It also keeps track of historical data, such as the deepest discharge and average discharge current, as well as the number of charge and discharge cycles. The smart shunt can also monitor the voltage of a 2nd battery, typically dedicated to engine starting. The product is a collaboration between Victron Energy and Digital Yacht. The system utilizes Victron’s proprietary VE.Direct data connectivity as a source for the NMEA 2000 data. The BM100 is part of a wider group of products now introduced by Digital Yacht that bring NMEA 2000 connectivity to Victron systems using the VE.Direct interface. Victron solar panel controllers (MPPTs) and battery monitors can now also interconnect to NMEA 2000 via the veKonvert interface. Monitoring the battery with the BM100 will give important feedback to the user so that remedial measures can be taken when necessary. Doing this will extend battery life. There’s also an optional battery temperature sensor available. The BM100 can also integrate with Digital Yacht’s other NMEA 2000 and wireless instruments, which offer hybrid NMEA 2000 and wireless display options. NMEA 2000 Interface The system features an NMEA 2000 interface, so your navigation multi-function display or plotter can display all key parameters. Modern MFDs from leading manufacturers such as Garmin, Raymarine, Furuno, and Navico allow electrical battery data to be displayed via their NMEA 2000 interface. Alarms and alerts for low capacity and voltage can also be enabled. Bluetooth Interface The BM100 also has a standalone wireless Bluetooth interface, so your mobile phone or iPad can connect and display current, voltage, capacity, additional historical data, state of charge information, and time to go based on remaining battery capacity. Specifications: BM100 solution comes as a complete package with SmartShunt and the veKonvert NMEA 2000 interface Bluetooth interface for setup and detailed analysis, including charge/discharge cycles, state of charge, remaining capacity, and historical data Use your phone/tablet and your NMEA 2000 devices for battery monitoring and management 500A SmartShunt included for the main battery system Monitor the voltage of a separate (eg starter) battery Universal NMEA 2000 gateway for Victron’s popular range of smart battery monitors/SmartShunt using the VE.Direct interface (see compatibility list in the FAQ tab) Enables electrical and battery monitoring and management on compatible multi-function displays (Raymarine, Garmin, Navico, Furuno, etc) Provides battery voltage, charge/discharge current, state of charge, and time to depletion based on a sophisticated algorithm Easy installation, plug ‘n play connectivity, and self-powering from the NMEA 2000 bus Supports alerts generated by the SmartShunt Supports multiple SmartShunts for multi-battery systems Also compatible with other VE.Direct products such as solar MPPT controllers Vekonvert Is Compatible with the Following Victron Products: BMV -700, BMV -702, BMV -700H, BMV-712 Smart, BMV-710H Smart, BMV-712 Smart Rev2, SmartShunt 500A/50mV, SmartShunt 1000A/50mV, SmartShunt 2000A/50mV, and All MPPT Charge Controllers NOTE: veKonvert is not compatible with Victron Chargers and Inverters. It should also not be plugged into the VE.Direct interfaces of any Victron "Consumers" such as Multiplus, Quattro, Cerbo, etc.

The Coast Guard's Seventh District has received at least three reports in the past few months regarding unapproved replacements of 406 EPIRB batteries by servicing companies having no association with the EPIRB manufacturer.  These unauthorized battery installations would likely result in a failure of this critical item of lifesaving equipment, and as such are not in compliance with the operational readiness requirements of 46 CFR. The following is a typical excerpt from an EPIRB manufacturer report: "The unit was opened and a foreign battery was found inside.  The battery was built up using (manufacturer) fuses and wiring salvaged from the original (manufacturer) battery.  They then covered their battery with the original (manufacturer) yellow heat shrink, (manufacturer) labels and taped it together.  This was then covered with a black heat shrink wrap.  The connections were soldered and not spot welded, as is required by the design and is performed in (manufacturer) production.  The battery measured 8.7 volts.  Our batteries read 9+ volts when they are new.  This battery was installed one week prior to it being brought into (manufacturer). There was also evidence of water intrusion due to the crack in the top cap, which (servicing company) did not recognize as they are not trained in these matters. The EPIRB was condemned by (manufacturer) and the customer was notified when he came to pick the unit up." Every approved (i.e., accepted by the FCC) EPIRB is tested during its approval process using a battery, or batteries, specified by the manufacturer.  Approved EPIRBs come with a user's manual which describes battery maintenance and replacement procedures.  In order for the EPIRB to remain within the conditions of its approval, the manufacturer's instructions in the user's manual must be adhered to.  To ensure that replacement batteries are of the same type with which the EPIRB was approved, and are correctly installed, manufacturers typically specify that battery replacements only be done by the manufacturer or a manufacturer-approved shop. Any modification or changes to an EPIRP must be made in accordance with the manufacturer.  The use of alternative replacement parts or batteries is prohibited and may prevent the device from meeting lifesaving requirements.  The Coast Guard strongly reminds EPIRB owners and servicing facilities to be aware of the compliance implications and potential for equipment failure stemming from any EPIRB modification or unauthorized battery replacement. This safety alert is provided for informational purposes only and does not relieve any domestic or international safety, operational or material requirement.  Questions regarding the information presented in this alert may be addressed to LCDR Vince Gamma of the U.S. Coast Guard Headquarters Lifesaving & Fire Safety Standards Division at 202.372.1396 or Vincent.A.Gamma at uscg.mil.

  The ProNautic Battery Charger from ProMariner is an award-winning charger with features that define the future of marine battery charging. Recognized with the 2010 IBEX Innovation Award, the ProNauticP combines digitally controlled and software-based power conversion technology with global energy management features to deliver global wide range AC input and power factor correction. This allows models to operate off standard household power connections anywhere in the world. The chargers address the trend of using greater numbers of 12-volt electronics on board today's power, sail, cruising and sport fishing boats. Featuring dual digital display screens, the ProNauticP series makes it easy to view real-time charging voltage, amperage and percentage of power out information. The ProNauticP charger automatically removes stress on a fully charged battery by incorporating a built-in conservation mode that reduces float voltage when the unit does not register a load greater than 5 amps over a 72-hour period and re-conditions batteries to improve battery life and reserve power performance every 21 days if in a storage state. ProMariner's Distributed-On-Demand Technology senses and distributes 100% of available charging to any one bank or a combination of all banks; all unused charging amps are distributed to batteries requiring them. The ProNauticP self-calculates absorption & conditioning time based on its ability to analyze the discharge state of the onboard battery banks and incorporates fully automatic temperature compensation as a standard feature on all models. The revolutionary ProNautic battery chargers are now in stock at CLR Marine! Available in amperages ranging from 10 to 60 amps.      Specials   Closeouts    Remanufactured    Rebates  

> Now On Sale!  Select Electrical Products from Ancor & Marinco Don't miss out on super savings now until July 31st, 2015 Select Ancor and Marinco products are on sale the entire month of July.   Don't miss out on these super savings!   Solid Products You Can Rely On From Ancor Don't miss out on super savings now until July 31st, 2015 Ancor Marine Grade™ Products quickly became the system of choice as the first major supplier of UL listed products designed for the harsh marine environment. Often imitated, never duplicated, Ancor continues to lead the industry by providing the most water resistant, flame retardant wiring products available. Marinco Products Designed to Withstand the Rigors of Life at Sea Don't miss out on super savings now until July 31st, 2015 Marinco makes electrical products that stand up to the harshest environments. Every product made, from the rugged shore power cordsets and adapters to a wide array of 12V accessories, is designed to withstand the rigors of life at sea.

Blue Sea Systems Products on Water or Land In addition to the marine industry, Blue Sea Systems products can be found on emergency vehicles, RVs, agricultural equipment, off-road vehicles, and other industries where rugged, dependable products are required. 7650 Add-A-Battery Add-a-Battery simplifies switching and automates charging for a complete two battery bank management solution.  The Dual Circuit Plus™ Battery Switch isolates engine and house circuits and combines battery banks for emergency starting. WeatherDeck 4376 Water Resistant Circuit Breaker Panel The 4376 WeatherDeck is a water resistant circuit breaker panel with 6 positions.  It is rated IP67 for temporary immersion for 30 minutes.  The 4376 is designed for flybridge and open cockpit applications. 5025 ST Blade Fuse Block with Cover The 5025 ST Blade Fuse Block with a clear, insulating cover has 6 circuits and a negative bus.  The 5025 can be used for 24-circuits and has a positive distribution bus with a #10-32 stud.  Models are available with or without a cover. 7748 SafetyHub 150 Fuse Block The SafetyHub 150 is an ignition protected fuse block with screw termination. It is safe for use on gasoline powered boats, reduces wiring connections, and consolidates up to ten fused circuits. It can be used for Main or Branch DC power distribution.

B.O.S. Battery Optimization System - 12V - 2-Bank B.O.S. actively shuttles energy between batteries to keep “the pack” balanced, increasing battery strength and longevity. Batteries in a pack will become “out of balance” and the pack is only as good as its “weakest link”. In watercraft applications, this is further compounded when the trolling motor battery is used for peripherals and/or to assist the cranking battery. B.O.S. actively shuttles energy as needed between batteries wired in series to ensure equal voltage before, during and after charging. B.O.S. keeps packs balanced, enabling maximum performance, and quadruples run time on the water. Premature battery failure due to an unbalanced pack has been, unfortunately, accepted as the ‘norm’ for decades. The B.O.S. answers this call with a BSAP-24 algorithm that can accurately predict and select the battery that needs additional energy to match the other batteries within the pack. This simultaneously and successfully extends the life of each battery in the pack, as well as increasing run times. Features: Available in 6V, 8V, and 12V configuration Up to six batteries in series Battery Selection and Prediction (BSAP-24) algorithm Less than 1mA sleep mode Transfer rate up to 7.5A Self-powered Any type of battery chemistry Used in any application where batteries are in series: Marine Golf Industrial Aerial Equipment Solar Power Electrical Vehicles Communications Defense/Military This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

B.O.S. Battery Optimization System - 12V - 3-Bank B.O.S. actively shuttles energy between batteries to keep “the pack” balanced, increasing battery strength and longevity. Batteries in a pack will become “out of balance” and the pack is only as good as its “weakest link”. In watercraft applications, this is further compounded when the trolling motor battery is used for peripherals and/or to assist the cranking battery. B.O.S. actively shuttles energy as needed between batteries wired in series to ensure equal voltage before, during and after charging. B.O.S. keeps packs balanced, enabling maximum performance, and quadruples run time on the water. Premature battery failure due to an unbalanced pack has been, unfortunately, accepted as the ‘norm’ for decades. The B.O.S. answers this call with a BSAP-24 algorithm that can accurately predict and select the battery that needs additional energy to match the other batteries within the pack. This simultaneously and successfully extends the life of each battery in the pack, as well as increasing run times. Features: Available in 6V, 8V, and 12V configuration Up to six batteries in series Battery Selection and Prediction (BSAP-24) algorithm Less than 1mA sleep mode Transfer rate up to 7.5A Self-powered Any type of battery chemistry Used in any application where batteries are in series: Marine Golf Industrial Aerial Equipment Solar Power Electrical Vehicles Communications Defense/Military This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

TRUECharge™2 Battery Charger 804-2410 10 Amp - 90-265 Vac / 47-63 Hz AMP-IT-UP! NEW 24-Volt Universal Chargers Building on the success of the TRUECharge™2 12-volt battery chargers, Xantrex™ now offers 24-volt battery chargers designed to meet the specific needs of marine and commercial markets. Available in 10A, 20A and 30A versions, each model packs a powerful universal charger (90-240Vac, 47-63 Hz) in an ultra-compact, lightweight package. Product Description TRUECharge2 battery chargers are highly versatile and can be mounted in multiple positions, thanks to their inherent drip-free design characteristics. TRUECharge2 delivers outstanding low electrical interference, coupled with efficient, power factor corrected, multistage charging capability. Installation is a breeze, thanks to the easy-access AC and DC wiring compartments. The easy-to-read display can be augmented with an optional remote panel. NEW PARALLEL FEATURE TRUECharge2 24-volt chargers are available with parallel stacking feature which allows you to double the output current when used with the optional REMOTE PANEL (part #808-8040-01). Performance Features 24-volt models available in 10A, 20A and 30A Microprocessor-controlled, multistage charging algorithms Settings for two and three-stage charging Settings for flooded, gel, AGM or lead-calcium batteries Auto-ranging universal input voltage (90-265 Vac, 47-63 Hz) is also compatible with a generator or other low-quality power sources Power factor corrected, temperature-compensated charging Battery-equalization feature Ability to charge batteries drained to extremely low voltage Optional Battery Temperature Sensor (Part #808-0232-01) Optional Remote Panel (#808-8040-01) Protection Features Reverse battery polarity protection Drip-proof design Over and under-temperature protection DC over-voltage protection Battery overcharging protection WARNING: This product can expose you to chemicals including Diisononyl Phthalate (DINP) which is known to the State of California to cause cancer, and Di-isodecyl Phthalate (DIDP) which is known to the State of California to cause reproductive harm. For more information go to P65Warnings.ca.gov.

TRUECharge™2 Battery Charger 804-2420 20 Amp - 90-265 Vac / 47-63 Hz AMP-IT-UP! NEW 24-Volt Universal Chargers Building on the success of the TRUECharge™2 12-volt battery chargers, Xantrex™ now offers 24-volt battery chargers designed to meet the specific needs of marine and commercial markets. Available in 10A, 20A and 30A versions, each model packs a powerful universal charger (90-240Vac, 47-63 Hz) in an ultra-compact, lightweight package. Product Description TRUECharge2 battery chargers are highly versatile and can be mounted in multiple positions, thanks to their inherent drip-free design characteristics. TRUECharge2 delivers outstanding low electrical interference, coupled with efficient, power factor corrected, multistage charging capability. Installation is a breeze, thanks to the easy-access AC and DC wiring compartments. The easy-to-read display can be augmented with an optional remote panel. NEW PARALLEL FEATURE TRUECharge2 24-volt chargers are available with parallel stacking feature which allows you to double the output current when used with the optional REMOTE PANEL (part #808-8040-01). Performance Features 24-volt models available in 10A, 20A and 30A Microprocessor-controlled, multistage charging algorithms Settings for two and three-stage charging Settings for flooded, gel, AGM or lead-calcium batteries Auto-ranging universal input voltage (90-265 Vac, 47-63 Hz) is also compatible with a generator or other low-quality power sources Power factor corrected, temperature-compensated charging Battery-equalization feature Ability to charge batteries drained to extremely low voltage Optional Battery Temperature Sensor (Part #808-0232-01) Optional Remote Panel (#808-8040-01) Protection Features Reverse battery polarity protection Drip-proof design Over and under-temperature protection DC over-voltage protection Battery overcharging protection WARNING: This product can expose you to chemicals including Diisononyl Phthalate (DINP) which is known to the State of California to cause cancer, and Di-isodecyl Phthalate (DIDP) which is known to the State of California to cause reproductive harm. For more information go to P65Warnings.ca.gov.

200A, 40V 3-Bank Ideal Battery Isolator Features: Waterproof Expoxy Sealed Construction Easy Connection Most Efficient use of Available Alternator Output Maximize Battery Performance Three year parts and labour warranty Analytic Systems introduces the IBI (Ideal Battery Isolator) for 1, 2 and 3 bank battery systems, allowing all the batteries to be fully charged from a single alternator while maintaining electrical isolation between the battery banks or between a vehicle and trailer. Ideal Diode technology uses MosFet Transistors and control circuitry to replace the diode used in a traditional battery isolator and reduces the voltage drop across the isolator to a mere 160 millivolts at 200 Amps of charging current and essentially zero volts at low current, so all the power of the alternator is applied to the batteries ensuring a full recharge every time. While the Ideal Battery Isolator is designed to be used with an alternator, it can also be used to convert a single bank battery charger to a 2 or 3 bank charger or as a pure diode between a vehicle and trailer or other remote load.

TRUECHARGE™3 20A 3 Bank Battery Charger - 12V TRUEcharge3 battery chargers lead the industry with a small footprint and ultra-compact design. In addition to meeting global safety and regulatory standards, TRUEcharge3 battery chargers feature low electrical interference and efficient power factor-corrected multistage charging. Thanks to their inherent drip-proof design characteristics, the TRUEcharge3 Chargers can be mounted in multiple positions. Unlike its predecessors, TRUEcharge3 is lithium-ion battery compatible. Designed for recreational and commercial applications worldwide, TRUEcharge3 accepts 90–265 Vac, and 47–63 Hz, which makes traveling abroad and handling poor-quality power a breeze. The easy-to-read display of the TRUEcharge3 12 V models can be enhanced with an optional remote panel. Each model comes with built-in protection against surges and spikes on the AC power line. Features: Microprocessor-controlled, multistage charging algorithms Settings for two and three-stage charging Battery-equalization feature Settings for flooded, gel, AGM, or lithium-ion batteries Equipped with parallel stacking (remote panel required) Ability to charge batteries drained to extremely low voltage Added quiet mode Protection Features: Reverse-battery polarity protection Drip-proof design DC over-voltage protection Over-temperature protection Circuit breaker protection Three-Stage Charging Multistage charging ensures batteries receive optimum charging, but with minimal wear and tear, regulating the voltage and current delivered to the batteries in three automatic stages: Bulk: Replaces 70–80% of the battery’s state-of-charge at the fastest possible rate Absorption: Replenishes the remaining 20–30% of charge, bringing the battery to a full charge at a slow, safe rate Float: Voltage is reduced and held constant to prevent damage and maintain batteries at a full charge for the remaining 20–30% of charge, bringing the battery to a full charge at a slow, safe rate Power Factor Corrected (PFC) Charging Less shore power is required for charging batteries, freeing up more usable AC power for running electrical devices and appliances and reducing the likelihood of tripping shore power breakers. Electrical Specifications (@ 25 degrees C unless otherwise noted): Output Current (nominal): 20 A  Output Voltage (nominal, depending on settings): Charge 14.2–15.5; Float 13.4–13.8 Vdc; 16 V DC Output Connections: Three AC Input Voltage: 90–265 Vac; 47–63 Hz 120 Vac, 230 Vac, 240 Vac nominal Temperature Compensation: Three settings  Charger Efficiency: > 80% Battery Type: Gel, Flooded, AGM, LiFePO4  Minimum Recommended Battery Bank Size: 40 Ah General Specifications: Operating Temperature Range: 0–60°C (32–140°F)  Storage Temperature -40–80°C (-40–176°F) Battery Connection: Three positive terminals and one negative terminal Dimensions (H x W x L): 70 x 170 x 250 mm (2.8 x 6.7 x 9.8”) Weight 2.2 kg (4.8 lb)  Regulatory Approvals  Meets CSA 60335-2-29, CE Marked for the Low Voltage Directive (safety) and the EMC Directive, UL1564, IEC 60335-2-29, IP32 per EN.IEC 60529, FCC Part 158, Canada ICES-003 Class B emissions limits, ABYC A-31, and DOE/CEC energy efficiency compliant. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

TRUECHARGE™3 40A 3 Bank Battery Charger - 12V TRUEcharge3 battery chargers lead the industry with a small footprint and ultra-compact design. In addition to meeting global safety and regulatory standards, TRUEcharge3 battery chargers feature low electrical interference and efficient power factor-corrected multistage charging. Thanks to their inherent drip-proof design characteristics, the TRUEcharge3 Chargers can be mounted in multiple positions. Unlike its predecessors, TRUEcharge3 is lithium-ion battery compatible. Designed for recreational and commercial applications worldwide, TRUEcharge3 accepts 90–265 Vac, and 47–63 Hz, which makes traveling abroad and handling poor-quality power a breeze. The easy-to-read display of the TRUEcharge3 12 V models can be enhanced with an optional remote panel. Each model comes with built-in protection against surges and spikes on the AC power line. Features: Microprocessor-controlled, multistage charging algorithms Settings for two and three-stage charging Battery-equalization feature Settings for flooded, gel, AGM, or lithium-ion batteries Equipped with parallel stacking (remote panel required) Ability to charge batteries drained to extremely low voltage Added quiet mode Protection Features: Reverse-battery polarity protection Drip-proof design DC over-voltage protection Over-temperature protection Circuit breaker protection Three-Stage Charging Multistage charging ensures batteries receive optimum charging, but with minimal wear and tear, regulating the voltage and current delivered to the batteries in three automatic stages: Bulk: Replaces 70–80% of the battery’s state-of-charge at the fastest possible rate Absorption: Replenishes the remaining 20–30% of charge, bringing the battery to a full charge at a slow, safe rate Float: Voltage is reduced and held constant to prevent damage and maintain batteries at a full charge for the remaining 20–30% of charge, bringing the battery to a full charge at a slow, safe rate Power Factor Corrected (PFC) Charging Less shore power is required for charging batteries, freeing up more usable AC power for running electrical devices and appliances and reducing the likelihood of tripping shore power breakers. Electrical Specifications (@ 25 degrees C unless otherwise noted): Output Current (nominal): 40 A  Output Voltage (nominal, depending on settings): Charge 14.2–15.5; Float 13.4–13.8 Vdc; 16 V DC Output Connections: Three AC Input Voltage: 90–265 Vac; 47–63 Hz 120 Vac, 230 Vac, 240 Vac nominal Temperature Compensation: Three settings  Charger Efficiency: > 80% Battery Type: Gel, Flooded, AGM, LiFePO4  Minimum Recommended Battery Bank Size: 80 Ah General Specifications: Operating Temperature Range: 0–60°C (32–140°F)  Storage Temperature -40–80°C (-40–176°F) Battery Connection: Three positive terminals and one negative terminal Dimensions (H x W x L): 70 x 170 x 250 mm (2.8 x 6.7 x 9.8”) Weight 2.2 kg (4.8 lb) Regulatory Approvals  Meets CSA 60335-2-29, CE Marked for the Low Voltage Directive (safety) and the EMC Directive, UL1564, IEC 60335-2-29, IP32 per EN.IEC 60529, FCC Part 158, Canada ICES-003 Class B emissions limits, ABYC A-31, and DOE/CEC energy efficiency compliant. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

TRUECHARGE™3 60A 3 Bank Battery Charger - 12V TRUEcharge3 battery chargers lead the industry with a small footprint and ultra-compact design. In addition to meeting global safety and regulatory standards, TRUEcharge3 battery chargers feature low electrical interference and efficient power factor-corrected multistage charging. Thanks to their inherent drip-proof design characteristics, the TRUEcharge3 Chargers can be mounted in multiple positions. Unlike its predecessors, TRUEcharge3 is lithium-ion battery compatible. Designed for recreational and commercial applications worldwide, TRUEcharge3 accepts 90–265 Vac, and 47–63 Hz, which makes traveling abroad and handling poor-quality power a breeze. The easy-to-read display of the TRUEcharge3 12 V models can be enhanced with an optional remote panel. Each model comes with built-in protection against surges and spikes on the AC power line. Features: Microprocessor-controlled, multistage charging algorithms Settings for two and three-stage charging Battery-equalization feature Settings for flooded, gel, AGM, or lithium-ion batteries Equipped with parallel stacking (remote panel required) Ability to charge batteries drained to extremely low voltage Added quiet mode Protection Features: Reverse-battery polarity protection Drip-proof design DC over-voltage protection Over-temperature protection Circuit breaker protection Three-Stage Charging Multistage charging ensures batteries receive optimum charging, but with minimal wear and tear, regulating the voltage and current delivered to the batteries in three automatic stages: Bulk: Replaces 70–80% of the battery’s state-of-charge at the fastest possible rate Absorption: Replenishes the remaining 20–30% of charge, bringing the battery to a full charge at a slow, safe rate Float: Voltage is reduced and held constant to prevent damage and maintain batteries at a full charge for the remaining 20–30% of charge, bringing the battery to a full charge at a slow, safe rate Power Factor Corrected (PFC) Charging Less shore power is required for charging batteries, freeing up more usable AC power for running electrical devices and appliances and reducing the likelihood of tripping shore power breakers. Electrical Specifications (@ 25 degrees C unless otherwise noted): Output Current (nominal): 60 A  Output Voltage (nominal, depending on settings): Charge 14.2–15.5; Float 13.4–13.8 Vdc; 16 V DC Output Connections: Three AC Input Voltage: 90–265 Vac; 47–63 Hz 120 Vac, 230 Vac, 240 Vac nominal Temperature Compensation: Three settings  Charger Efficiency: > 80% Battery Type: Gel, Flooded, AGM, LiFePO4  Minimum Recommended Battery Bank Size: 120 Ah  General Specifications: Operating Temperature Range: 0–60°C (32–140°F)  Storage Temperature -40–80°C (-40–176°F) Battery Connection: Three positive terminals and one negative terminal Dimensions (H x W x L): 90 x 170 x 340 mm (3.5 x 6.7 x 13.4”) Weight 4.5 kg (9.9 lb) Regulatory Approvals  Meets CSA 60335-2-29, CE Marked for the Low Voltage Directive (safety) and the EMC Directive, UL1564, IEC 60335-2-29, IP32 per EN.IEC 60529, FCC Part 158, Canada ICES-003 Class B emissions limits, ABYC A-31, and DOE/CEC energy efficiency compliant. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

TRUECHARGE™3 10A 3 Bank Battery Charger - 24V TRUEcharge3 battery chargers lead the industry with a small footprint and ultra-compact design. In addition to meeting global safety and regulatory standards, TRUEcharge3 battery chargers feature low electrical interference and efficient power factor-corrected multistage charging. Thanks to their inherent drip-proof design characteristics, the TRUEcharge3 Chargers can be mounted in multiple positions. Unlike its predecessors, TRUEcharge3 is lithium-ion battery compatible. Designed for recreational and commercial applications worldwide, TRUEcharge3 accepts 90–265 Vac, and 47–63 Hz, which makes traveling abroad and handling poor-quality power a breeze. The easy-to-read display of the TRUEcharge3 24 V models can be enhanced with an optional remote panel. Each model comes with built-in protection against surges and spikes on the AC power line. Features: Microprocessor-controlled, multistage charging algorithms Settings for two and three-stage charging Battery-equalization feature Settings for flooded, gel, AGM, or lithium-ion batteries Equipped with parallel stacking (remote panel required) Ability to charge batteries drained to extremely low voltage Added quiet mode Protection Features: Reverse-battery polarity protection Drip-proof design DC over-voltage protection Over-temperature protection Circuit breaker protection Three-Stage Charging Multistage charging ensures batteries receive optimum charging, but with minimal wear and tear, regulating the voltage and current delivered to the batteries in three automatic stages: Bulk: Replaces 70–80% of the battery’s state-of-charge at the fastest possible rate Absorption: Replenishes the remaining 20–30% of charge, bringing the battery to a full charge at a slow, safe rate Float: Voltage is reduced and held constant to prevent damage and maintain batteries at a full charge for the remaining 20–30% of charge, bringing the battery to a full charge at a slow, safe rate Power Factor Corrected (PFC) Charging Less shore power is required for charging batteries, freeing up more usable AC power for running electrical devices and appliances and reducing the likelihood of tripping shore power breakers. Electrical Specifications (@ 25 degrees C unless otherwise noted): Output Current (nominal): 10 A  Output Voltage (nominal, depending on settings): Charge 28.4–31.0 Vdc; Float 26.8–27.6 Vdc; 32 Vdc DC Output Connections: Three AC Input Voltage: 90–265 Vac; 47–63 Hz 120 Vac, 230 Vac, 240 Vac nominal Temperature Compensation: Three settings  Charger Efficiency: > 80% Battery Type: Gel, Flooded, AGM, LiFePO4  Minimum Recommended Battery Bank Size: 20 Ah General Specifications: Operating Temperature Range: 0–60°C (32–140°F)  Storage Temperature -40–80°C (-40–176°F) Battery Connection: Three positive terminals and one negative terminal Dimensions (H x W x L): 70 x 170 x 250 mm (2.8 x 6.7 x 9.8”) Weight 2.2 kg (4.8 lb) Regulatory Approvals  Meets CSA 60335-2-29, UL1564, IEC 60335-2-29, IP32 per EN.IEC 60529, FCC Part 158, Canada ICES-003 Class B emissions limits, ABYC A-31, and DOE/CEC energy efficiency compliant. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

TRUECHARGE™3 20A 3 Bank Battery Charger - 24V TRUEcharge3 battery chargers lead the industry with a small footprint and ultra-compact design. In addition to meeting global safety and regulatory standards, TRUEcharge3 battery chargers feature low electrical interference and efficient power factor-corrected multistage charging. Thanks to their inherent drip-proof design characteristics, the TRUEcharge3 Chargers can be mounted in multiple positions. Unlike its predecessors, TRUEcharge3 is lithium-ion battery compatible. Designed for recreational and commercial applications worldwide, TRUEcharge3 accepts 90–265 Vac, and 47–63 Hz, which makes traveling abroad and handling poor-quality power a breeze. The easy-to-read display of the TRUEcharge3 24 V models can be enhanced with an optional remote panel. Each model comes with built-in protection against surges and spikes on the AC power line. Features: Microprocessor-controlled, multistage charging algorithms Settings for two and three-stage charging Battery-equalization feature Settings for flooded, gel, AGM, or lithium-ion batteries Equipped with parallel stacking (remote panel required) Ability to charge batteries drained to extremely low voltage Added quiet mode Protection Features: Reverse-battery polarity protection Drip-proof design DC over-voltage protection Over-temperature protection Circuit breaker protection Three-Stage Charging Multistage charging ensures batteries receive optimum charging, but with minimal wear and tear, regulating the voltage and current delivered to the batteries in three automatic stages: Bulk: Replaces 70–80% of the battery’s state-of-charge at the fastest possible rate Absorption: Replenishes the remaining 20–30% of charge, bringing the battery to a full charge at a slow, safe rate Float: Voltage is reduced and held constant to prevent damage and maintain batteries at a full charge for the remaining 20–30% of charge, bringing the battery to a full charge at a slow, safe rate Power Factor Corrected (PFC) Charging Less shore power is required for charging batteries, freeing up more usable AC power for running electrical devices and appliances and reducing the likelihood of tripping shore power breakers. Electrical Specifications (@ 25 degrees C unless otherwise noted): Output Current (nominal): 20 A  Output Voltage (nominal, depending on settings): Charge 28.4–31.0 Vdc; Float 26.8–27.6 Vdc; 32 Vdc DC Output Connections: Three AC Input Voltage: 90–265 Vac; 47–63 Hz 120 Vac, 230 Vac, 240 Vac nominal Temperature Compensation: Three settings  Charger Efficiency: > 80% Battery Type: Gel, Flooded, AGM, LiFePO4  Minimum Recommended Battery Bank Size: 40 Ah  General Specifications: Operating Temperature Range: 0–60°C (32–140°F)  Storage Temperature -40–80°C (-40–176°F) Battery Connection: Three positive terminals and one negative terminal Dimensions (H x W x L): 70 x 170 x 250 mm (2.8 x 6.7 x 9.8”) Weight 2.2 kg (4.8 lb) Regulatory Approvals  Meets CSA 60335-2-29, UL1564, IEC 60335-2-29, IP32 per EN.IEC 60529, FCC Part 158, Canada ICES-003 Class B emissions limits, ABYC A-31, and DOE/CEC energy efficiency compliant. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.