Little Giant Mag-Drive 230 Volt Pump 583513 Little Giant 5-MD-SC-230V Magnetic Drive Pump Motor 230 Volt 50/60 Hz 1/8 HP Open Fan Cooled Motor, 1050 GPH at 1 Foot Head, Shutoff Head 27.5 Feet, Inlet: 1" FNPT, Outlet: 1/2" MNPT, Polypropylene Body, Fluid Temperature Up to 150F (66C), UR/C-CSA Listed, 6 Foot Power Cord- No Plug   583513 Magnetically driven pump for circulation of moderately corrosive acids, alkalis, solvents, brine, plating solutions, sterile solutions, and other moderately corrosive chemicals and solutions that are compatible with the pump's material of construction. The MD-SC Series features leakproof, seal-less magnetic drives and is designed for in-line, non-submersed use

Little Giant Mag-Drive Pump 588001 Little Giant 1-AA-MD Magnetic Drive Pump Motor 115 Volt 60Hz 1/200 HP Open Motor, 160 GPH at 1 Foot Head, Shutoff Head 5.4 Feet, 1 Inlet: 1/2" Hose Barb, Outlet: 1/2" Hose Barb, Polypropylene Body, Fluid Temperature Up to 150F (66C), UR/C-CSA Listed, 3 Foot Wire Leads    # Model Intake Size Discharge Listing HP Volts Hertz Amps Watts Performance (GPH @ Head) Shut Off Power Cord (ft) Weight (lbs) 1' 3' Ft PSI 588001 1-AA-MD 1/2" Hose 1/2" Hose UR/C-CSA 1/200 115 60 0.4 19 162 102 5.4 2.3 6 2.33   588001 Magnetically driven pump for mildly corrosive chemicals and solutions. The MD Series features leakproof, seal-less magnetic drives and are designed for in-line, non-submersed use. Open shaded-pole motor has sleeve bearings and is impedance protected.   Circulation of mildly corrosive acids, alkalis, solvents, brine, plating solutions, sterile solutions, and other mildly corrosive chemicals and solutions that are compatible with the pump's material of construction

Little Giant Pump 586604 Little Giant TE-6-MD-HC Magnetic Drive Pump Motor 115/230 Volt 50/60 Hz 1/2 HP Totally Enclosed Fan Cooled Motor, 2280 GPH at 5 Foot Head, Shutoff Head 51 Feet, Inlet: 1" FNPT, Outlet: 3/4" MNPT, Ryton Body, Fluid Temperature Up to 200F (93C), UR/C-CSA Listed, with Conduit Box- No Power Cord   586604 Magnetically driven pumps for highly corrosive chemicals and solutions. The MD-HC Series features leakproof, seal-less magnetic drives and are designed for in-line, non-submersed use

Little Giant Mag-Drive Pump 566716 Little Giant PES-130-PW Magnetic Drive Statuary Fountain Pump Motor 120 Volt 60 Hz Epoxy Encapsulated Motor, 130 GPH at 1 Foot Head, Shutoff Head 5.5 Feet, Inlet: Screened, Outlet: 3/8" or 1/2" Hose Barb, Adjustable Flow Control, 6 Foot Power Cord   566716 Mag-drive pumps utilize an epoxy-encapsulated motor and plastic housing. A permanent magnet is attached to the impeller and acts as the rotor would in a conventional motor. The water being pumped surrounds the rotor. They are seal-less and oil-less

Little Giant Mag-Drive Pump 581031 Little Giant 3-MDX Magnetic Drive Pump Motor 115 Volt 60 Hz 1/25 HP Open Fan Cooled Motor, 456 GPH at 1 Foot Head, Shutoff Head 19 Feet, Inlet: 5/8" Hose Barb, Outlet: 5/8" Hose Barb, Polypropylene Body, Fluid Temperature Up to 150F (66C), UR/C-CSA Listed, 6 Foot Power Cord   581031 Magnetically driven pump for Circulation of mildly corrosive acids, alkalis, solvents, brine, plating solutions, sterile solutions, and other mildly corrosive chemicals and solutions that are compatible with the pump's material of construction

Little Giant Submersible Pump 503103 Little Giant 3E-12N Submersible or In-Line Pump Motor 115 Volt 60 Hz 1/15 HP Permanently Lubricated Oil Filled Motor, 500 GPH at 1 Foot Head, Shutoff Head 17.3 Feet, Inlet: 1/2" FNPT or Screened, Outlet: 1/2" MNPT and 3/4" Tubing, Epoxy Coated Aluminum Housing, Nylon Body, Viton Seal, Fluid Temperature Up to 120F (49C), UL Listed, 6 Foot Power Cord   Dual purpose oil-filled pump that may be used totally submersed or in-line (fed with pipe or hose). For commercial, industrial and home applications including statuary fountains, water displays, air conditioners, machine tool coolants, and many other applications where liquid must be transferred or recirculated.   It is not recommended to use the 3E series in aquariums, swimming pools and fuel oil transfer applications

Little Giant 3-MD-SC Mag-Drive Pump 581513 Little Giant 3-MD-SC 230V Magnetic Drive Pump This Pump will handle up to a 48,000 BTU Air Conditioner Motor 230 Volt 60 Hz 1/12 HP Open Fan Cooled Motor, 750 GPH at 1 Foot Head, Shutoff Head 21.9 Feet, Inlet: 3/4" FNPT, Outlet: 1/2" MNPT, Polypropylene Body, Fluid Temperature Up to 150F (66C), UR/C-CSA Listed, 6 Foot Power Cord   581513 Magnetically driven pump for semi-corrosive chemicals and solutions. The MD-SC Series features leakproof, seal-less magnetic drives and are designed for in-line, non-submersed use

Little Giant Mag-Drive Pump 583503 Little Giant 5-MD-SC Magnetic Drive Pump Motor 115 Volt 50/60 Hz 1/8 HP Open Fan Cooled Motor, 1050 GPH at 1 Foot Head, Shutoff Head 27.5 Feet, Inlet: 1" FNPT, Outlet: 1/2" MNPT, Polypropylene Body, Fluid Temperature Up to 150F (66C), UR/C-CSA Listed, 6 Foot Power Cord   583503 Magnetically driven pump for Circulation of moderately corrosive acids, alkalis, solvents, brine, plating solutions, sterile solutions, and other moderately corrosive chemicals and solutions that are compatible with the pump's material of construction. The MD-SC Series features leakproof, seal-less magnetic drives and is designed for in-line, non-submersed use

Little Giant Mag Drive Pump 566714 Little Giant PES-80-PW Mag-Drive Statuary Fountain Pump Motor 120 Volt 60 Hz Epoxy Encapsulated Motor, 80 GPH at 1 Foot Head, Shutoff Head 3.5 Feet, Inlet: Screened, Outlet: 3/8" or 1/2" Hose Barb, Adjustable Flow Control, 6 Foot Power Cord   566714 Mag-drive pumps utilize an epoxy-encapsulated motor and plastic housing. A permanent magnet is attached to the impeller and acts as the rotor would in a conventional motor. The water being pumped surrounds the rotor. They are seal-less and oil-less

Little Giant Pump 115/208-230 Volts 587010 Little Giant TE-7-MD-HC Magnetic Drive Pump The motor is 115/208-230 Volt 50/60 Hz 3/4 HP Totally Enclosed Fan Cooled Motor, 3180 GPH at 1 Foot Head, Shutoff Head 58.9 Feet, Inlet: 1-1/2" FNPT, Outlet: 1" MNPT, Ryton Body, Fluid Temperature Up to 200F (93C), UR/C-CSA Listed, With Conduit Box   587010 Magnetically driven pump for circulation of highly corrosive acids, alkalis, solvents, brine, plating solutions, sterile solutions, and other highly corrosive chemicals and solutions. The MD-HC Series features leakproof, seal-less magnetic drives and are designed for in-line, non-submersed use

March 1A-MD-1/2 Mag Drive Pump March Pump's industrial 1A-MD-1/2 is an American submersible seal-less centrifugal magnetic drive pump. It is capable of generating a maximum flow of 3 gallons per minute at 0.25 feet, and its maximum head is 4.5 Feet (or around 2PSI).  The 1A-MD-1/2 pump may be used submerged or not submerged. The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Buna N, Nylon, Carbon/Teflon, and Stainless Steel.  When submerged, Epoxy, Noryl, and the SJT Cord are also in contact with the solution. The inlet connection is 1/2 inch smooth, and the outlet is 1/2 inch smooth. The standard motor is a 1 Phase 230V 0.005 Horsepower motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheit or 160 Celsius in open air, or 87 Fahrenheit or 71 Celsius if submerged. The March 1A-MD-1/2 centrifugal magnetic drive pump is capable of handling fresh water, salt water, and mild chemicals. To determine if the March 1A-MD-1/2 is suitable for your application, please contact March Pump.   Perfect for Applications Including Applications for the 1A-MD-1/2 Magnetic Drive Pump include chemical transfer, photographic processing equipment, refrigeration systems, and water displays.   Great for Chemicals Including The 1A-MD-1/2 has pumped Acetone, Ammonium Chloride, Ammonium Chloride, Ammonium Hydroxide, Citric Acid, Ethylene Glycol, Magnesium Nitrate, Potassium Carbonate, Sodium Borate, Fresh Water, Salt Water, and many more chemicals.   Inlet: 1/2"OD Outlet: 1/2"OD Wet End: Polypropylene (Front Housing, Rear Housing, Impeller), Buna N (O-Ring), Carbon/Teflon (Thrust Washer), 316 Stainless Steel (Shaft) Uses:Submersible or Open Air When submerged, the following is also in contact with the solutionEpoxy, Noryl, SJT Cord   P/N 0115-0007-0700 (230V)

Applications for the  March 1C-MD Magnetic Drive Pump include chemical transfer, photographic processing equipment, refrigeration systems, and water displays.      March Pump's industrial 1C-MD is an American submersible seal-less centrifugal magnetic drive pump. It is capable of generating a maximum flow of 2.3 gallons per minute at 0.25 feet, and its maximum head is 4.5 Feet (or around 2PSI).  The 1C-MD pump may be used submerged or not submerged. The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Buna N, Nylon, Carbon/Teflon, Stainless steel, and Ceramic Magnet.  When submerged, Epoxy, Noryl, and the SJT Cord are also in contact with the solution. The inlet connection is 0.25 inch male pipe thread, and the outlet is 0.25 inch male pipe thread. The standard motor is a 1 Phase 115V or 230V 0.005 Horsepower motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheit or 160 Celsius in open air, or 87 Fahrenheit or 71 Celsius if submerged. The March 1C-MD centrifugal magnetic drive pump is capable of handling fresh water, salt water, and mild chemicals.      Unit System 60Hz 50Hz Max Flow 3 GPM 9 LPM Max Head 4.6 FT 1 M Power .005 HP .003 KW Electrical 115V 50/60HZ or 230V 50/60HZ Submersible Yes   Type Centrifugal Mag Drive Inlet 1/4"MPT Outlet 1/4"MPT Wet End Polypropylene (Front and Rear Housing), Buna N (O-Ring), Nylon (Impeller), Carbon/Teflon (Thrust Washer), 316 Stainless Steel (Shaft), Ceramic Magnet Uses Submersible or Open Air When submerged, the following is also in contact with the solution Epoxy, Noryl, SJT Cord  

Applications for the 1U-MD Magnetic Drive Pump include chemical transfer, photographic processing equipment, refrigeration systems, and water displays.    March Pump's industrial 1U-MD is an American submersible seal-less centrifugal magnetic drive pump. It is capable of generating a maximum flow of 2.3 gallons per minute at 0.25 feet, and its maximum head is 4.5 Feet (or around 2PSI).  The 1U-MD pump must be used submerged. The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Buna N, Nylon, Carbon/Teflon, Stainless Steel, Cycolac, Delrin, and Ceramic Magnet.  When submerged, Epoxy, Noryl, Cycolac, Delrin, and the SJT Cord are also in contact with the solution. The inlet connection is a screen, and the outlet is 0.25 inch male pipe thread. The standard motor is a 1 Phase 115V or 230V 0.005 Horsepower motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheit or 160 Celsius in open air, or 87 Fahrenheit or 71 Celsius if submerged. The March 1U-MD centrifugal magnetic drive pump is capable of handling fresh water, salt water, and mild chemicals.      Unit System 60Hz 50Hz Max Flow 3 GPM 9 LPM Max Head 4.6 FT 1 M Power .005 HP .003 KW Electrical 115V 50/60HZ or 230V 50/60HZ Submersible Yes     Type Centrifugal Mag Drive Inlet Screen Outlet 1/4"MPT Wet End Polypropylene (Rear Housing), Buna N (O-Ring), Nylon (Impeller), Cycolac (Cover), Carbon/Teflon (Thrust Washer), Delrin (Screen), 316 Stainless Steel (Shaft), Ceramic Magnet Uses Submersible or Open Air When submerged, the following is also in contact with the solution Epoxy, Noryl, Cycolac, Delrin, SJT Cord    

Applications for the March AC-1A-MD-1/2 Magnetic Drive Pump include chemical transfer, photographic processing equipment, refrigeration systems, and water displays.   The AC-1A-MD-1/2 Part # 0115-0064-0200 has pumped Acetone, Ammonium Chloride, Ammonium Chloride, Ammonium Hydroxide, Citric Acid, Ethylene Glycol, Magnesium Nitrate, Potassium Carbonate, Sodium Borate, Fresh Water, Salt Water, and many more chemicals.  The AC-1A-MD-1/2 may have been modified to handle these chemicals.    March Pump's industrial AC-1A-MD-1/2 is an American seal-less centrifugal magnetic drive pump ideal for applications such as chemical recirculation and chemical transfer. It is capable of generating a maximum flow of 3 gallons per minute at 0.25 feet, and its maximum head is 4.6 Feet (or around 2PSI). The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Buna N, Nylon, Carbon/Teflon, Stainless Steel, and Ceramic Magnet. The inlet connection is 0.5 inch smooth, and the outlet is 0.5 inch smooth. The standard motor is a 1 Phase 115V or 230V 0.05 Horsepower motor, which can be run on 60 hertz on 115V or 50 and 60 hertz on 230V (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheit or 87 Celsius. The March AC-1A-MD-1/2 centrifugal magnetic drive pump is capable of handling mildly or highly corrosive chemicals, acids, and solvents. To determine if the March AC-1A-MD-1/2 is suitable for your application, please contact March Pump.      Unit System 60Hz 50Hz Max Flow 3 GPM 9 LPM Max Head 4.6 FT 1 M Power .005 HP .003 KW Electrical 115V 60HZ       230V 50/60HZ   Type Centrifugal Mag Drive Inlet 1/2"OD Outlet 1/2"OD Wet End Polypropylene (Front and Rear Housing), Buna N (O-Ring), Nylon (Impeller), Carbon/Teflon (Thrust Washer), 316 Stainless Steel (Shaft), Ceramic Magnet   Part # 0115-0064-0200

Applications for the March AC-1A-MD-3/8 Magnetic Drive Pump include photographic processing equipment, refrigeration systems, and water displays.   The AC-1A-MD-3/8 has pumped Acetone, Ammonium Chloride, Ammonium Chloride, Ammonium Hydroxide, Citric Acid, Ethylene Glycol, Magnesium Nitrate, Potassium Carbonate, Sodium Borate, Fresh Water, Salt Water, and many more chemicals.  The AC-1A-MD-3/8 may have been modified to handle these chemicals.   March Pump's industrial AC-1A-MD-3/8 is an American seal-less centrifugal magnetic drive pump ideal for applications such as chemical recirculation and chemical transfer. It is capable of generating a maximum flow of 2.3 gallons per minute at 0.25 feet, and its maximum head is 4.6 Feet (or around 2PSI). The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Buna N, Nylon, Carbon/Teflon, Stainless Steel, and Ceramic Magnet. The inlet connection is 0.375 inch smooth, and the outlet is 0.375 inch smooth. The standard motor is a 1 Phase 115V or 230V 0.05 Horsepower motor, which can be run on 60 hertz on 115V or 50 and 60 hertz on 230V (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheit or 87 Celsius. The March AC-1A-MD-3/8 centrifugal magnetic drive pump is capable of handling mildly or highly corrosive chemicals, acids, and solvents.      Unit System 60Hz 50Hz Max Flow 2.3 GPM 8.7 LPM Max Head 4.6 FT 1 M Power .005 HP .003 KW Electrical 115V 60HZ          230V 50/60HZ   Type Centrifugal Mag Drive Inlet 3/8"OD Outlet 3/8"OD Wet End Polypropylene (Front and Rear Housing), Buna N (O-Ring), Nylon (Impeller), Carbon/Teflon (Thrust Washer), 316 Stainless Steel (Shaft), Ceramic Magnet