Applications for the March AC-1A-MD-1/2 Magnetic Drive Pump include chemical transfer, photographic processing equipment, refrigeration systems, and water displays.   The AC-1A-MD-1/2 Part # 0115-0064-0200 has pumped Acetone, Ammonium Chloride, Ammonium Chloride, Ammonium Hydroxide, Citric Acid, Ethylene Glycol, Magnesium Nitrate, Potassium Carbonate, Sodium Borate, Fresh Water, Salt Water, and many more chemicals.  The AC-1A-MD-1/2 may have been modified to handle these chemicals.    March Pump's industrial AC-1A-MD-1/2 is an American seal-less centrifugal magnetic drive pump ideal for applications such as chemical recirculation and chemical transfer. It is capable of generating a maximum flow of 3 gallons per minute at 0.25 feet, and its maximum head is 4.6 Feet (or around 2PSI). The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Buna N, Nylon, Carbon/Teflon, Stainless Steel, and Ceramic Magnet. The inlet connection is 0.5 inch smooth, and the outlet is 0.5 inch smooth. The standard motor is a 1 Phase 115V or 230V 0.05 Horsepower motor, which can be run on 60 hertz on 115V or 50 and 60 hertz on 230V (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheit or 87 Celsius. The March AC-1A-MD-1/2 centrifugal magnetic drive pump is capable of handling mildly or highly corrosive chemicals, acids, and solvents. To determine if the March AC-1A-MD-1/2 is suitable for your application, please contact March Pump.      Unit System 60Hz 50Hz Max Flow 3 GPM 9 LPM Max Head 4.6 FT 1 M Power .005 HP .003 KW Electrical 115V 60HZ       230V 50/60HZ   Type Centrifugal Mag Drive Inlet 1/2"OD Outlet 1/2"OD Wet End Polypropylene (Front and Rear Housing), Buna N (O-Ring), Nylon (Impeller), Carbon/Teflon (Thrust Washer), 316 Stainless Steel (Shaft), Ceramic Magnet   Part # 0115-0064-0200

Applications for the March AC-1A-MD-1/2 Magnetic Drive Pump include chemical transfer, photographic processing equipment, refrigeration systems, and water displays.   The AC-1A-MD-1/2 Part # 0115-0064-0100 has pumped Acetone, Ammonium Chloride, Ammonium Chloride, Ammonium Hydroxide, Citric Acid, Ethylene Glycol, Magnesium Nitrate, Potassium Carbonate, Sodium Borate, Fresh Water, Salt Water, and many more chemicals.  The AC-1A-MD-1/2 may have been modified to handle these chemicals.    March Pump's industrial AC-1A-MD-1/2 is an American seal-less centrifugal magnetic drive pump ideal for applications such as chemical recirculation and chemical transfer. It is capable of generating a maximum flow of 3 gallons per minute at 0.25 feet, and its maximum head is 4.6 Feet (or around 2PSI). The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Buna N, Nylon, Carbon/Teflon, Stainless Steel, and Ceramic Magnet. The inlet connection is 0.5 inch smooth, and the outlet is 0.5 inch smooth. The standard motor is a 1 Phase 115V or 230V 0.05 Horsepower motor, which can be run on 60 hertz on 115V or 50 and 60 hertz on 230V (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheit or 87 Celsius. The March AC-1A-MD-1/2 centrifugal magnetic drive pump is capable of handling mildly or highly corrosive chemicals, acids, and solvents.     Unit System 60Hz 50Hz Max Flow 3 GPM 9 LPM Max Head 4.6 FT 1 M Power .005 HP .003 KW Electrical 115V 60HZ     230V 50/60HZ   Type Centrifugal Mag Drive Inlet 1/2"OD Outlet 1/2"OD Wet End Polypropylene (Front and Rear Housing), Buna N (O-Ring), Nylon (Impeller), Carbon/Teflon (Thrust Washer), 316 Stainless Steel (Shaft), Ceramic Magnet   Part # 0115-0064-0100

Applications for the March AC-1A-MD-3/8 Magnetic Drive Pump include photographic processing equipment, refrigeration systems, and water displays.   The AC-1A-MD-3/8 has pumped Acetone, Ammonium Chloride, Ammonium Chloride, Ammonium Hydroxide, Citric Acid, Ethylene Glycol, Magnesium Nitrate, Potassium Carbonate, Sodium Borate, Fresh Water, Salt Water, and many more chemicals.  The AC-1A-MD-3/8 may have been modified to handle these chemicals.   March Pump's industrial AC-1A-MD-3/8 is an American seal-less centrifugal magnetic drive pump ideal for applications such as chemical recirculation and chemical transfer. It is capable of generating a maximum flow of 2.3 gallons per minute at 0.25 feet, and its maximum head is 4.6 Feet (or around 2PSI). The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Buna N, Nylon, Carbon/Teflon, Stainless Steel, and Ceramic Magnet. The inlet connection is 0.375 inch smooth, and the outlet is 0.375 inch smooth. The standard motor is a 1 Phase 115V or 230V 0.05 Horsepower motor, which can be run on 60 hertz on 115V or 50 and 60 hertz on 230V (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheit or 87 Celsius. The March AC-1A-MD-3/8 centrifugal magnetic drive pump is capable of handling mildly or highly corrosive chemicals, acids, and solvents.      Unit System 60Hz 50Hz Max Flow 2.3 GPM 8.7 LPM Max Head 4.6 FT 1 M Power .005 HP .003 KW Electrical 115V 60HZ          230V 50/60HZ   Type Centrifugal Mag Drive Inlet 3/8"OD Outlet 3/8"OD Wet End Polypropylene (Front and Rear Housing), Buna N (O-Ring), Nylon (Impeller), Carbon/Teflon (Thrust Washer), 316 Stainless Steel (Shaft), Ceramic Magnet

Applications for the March AC-1A-MD-3/8 Magnetic Drive Pump include photographic processing equipment, refrigeration systems, and water displays.   The AC-1A-MD-3/8 Part # 0115-0064-0300 has pumped Acetone, Ammonium Chloride, Ammonium Chloride, Ammonium Hydroxide, Citric Acid, Ethylene Glycol, Magnesium Nitrate, Potassium Carbonate, Sodium Borate, Fresh Water, Salt Water, and many more chemicals.  The AC-1A-MD-3/8 may have been modified to handle these chemicals.    March Pump's industrial AC-1A-MD-3/8 is an American seal-less centrifugal magnetic drive pump ideal for applications such as chemical recirculation and chemical transfer. It is capable of generating a maximum flow of 2.3 gallons per minute at 0.25 feet, and its maximum head is 4.6 Feet (or around 2PSI). The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Buna N, Nylon, Carbon/Teflon, Stainless Steel, and Ceramic Magnet. The inlet connection is 0.375 inch smooth, and the outlet is 0.375 inch smooth. The standard motor is a 1 Phase 115V or 230V 0.05 Horsepower motor, which can be run on 60 hertz on 115V or 50 and 60 hertz on 230V (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheit or 87 Celsius. The March AC-1A-MD-3/8 centrifugal magnetic drive pump is capable of handling mildly or highly corrosive chemicals, acids, and solvents.     Unit System 60Hz 50Hz Max Flow 2.3 GPM 8.7 LPM Max Head 4.6 FT 1 M Power .005 HP .003 KW Electrical 115V 60HZ      230V 50/60HZ   Type Centrifugal Mag Drive Inlet 3/8"OD Outlet 3/8"OD Wet End Polypropylene (Front and Rear Housing), Buna N (O-Ring), Nylon (Impeller), Carbon/Teflon (Thrust Washer), 316 Stainless Steel (Shaft), Ceramic Magnet     Part # 0115-0064-0300  

March Mag-Drive Centrifugal Pumps Bronze 230V High Speed 4.5GPM   The March MAGNE-BOOST Hydronic hot water booster pumps are a non-self priming unit built to handle liquid transfer in heating and cooling operations. Typical applications include home heating systems, solar heating systems, heat recovery systems and recirculating water in domestic and commercial hot water tanks. These pumps are not food rated. • Brewery pump - the March 809 and 815 series of pumps are commonly used by Home Brewers and Breweries. • Maximum liquid temperature for the 809 and 815 series is 250 F. • Port configurations include in-line and center inlet with side discharge. • Construction materials: Bronze, Stainless Steel, Ryton/Polysulfil Plastic. Impellers are Teflon plastic. • There are many motor options available Including AC, DC and High Speed versions for added flow.   March Pump Mag-Drive Centrifugal Pump Bronze Center Inlet 230V High Speed 4.5GPM 3/4"MPT Inlet, 1/2"MPT Outlet  

March 815 Series Mag-Drive Centrifugal Pumps The March MAGNE-BOOST Hydronic hot water booster pumps are a non-self priming unit built to handle liquid transfer in heating and cooling operations. Typical applications include home heating systems, solar heating systems, heat recovery systems and recirculating water in domestic and commercial hot water tanks. These pumps are not food rated. •  Brewery pump - the March 809 and 815 series of pumps are commonly used by Home Brewers and Breweries. •  Maximum liquid temperature for the 809 and 815 series is 250 F. •  Port configurations include in-line and center inlet with side discharge. •  Construction materials: Bronze, Stainless Steel, Ryton/Polysulfil Plastic. Impellers are Teflon plastic. •  There are many motor options available Including AC, DC and High Speed versions for added flow.   March Pump Mag-Drive Centrifugal Pump Bronze 230V High Speed 7.2GPM 1/2"MPT Ports    

IWAKI MD-6Z, 220volt HIGH HEAD MAG DRIVE PUMP Iwaki Mag Drive Centrifugal Pump and Motor Assembly, High head impeller, GFRPP Polypropylene Construction, close coupled to a 1/250 Horsepower, 220 Volts AC, 1 Phase Electric Motor. 35/64 Inch Hose Barb Port Connections.

March 809 815 Series Mag-Drive Centrifugal Pumps The March MAGNE-BOOST Hydronic hot water booster pumps are a non-self priming unit built to handle liquid transfer in heating and cooling operations. Typical applications include home heating systems, solar heating systems, heat recovery systems and recirculating water in domestic and commercial hot water tanks. These pumps are not food rated. • Brewery pump - the March 809 and 815 series of pumps are commonly used by Home Brewers and Breweries. • Maximum liquid temperature for the 809 and 815 series is 250 F. • Port configurations include in-line and center inlet with side discharge. • Construction materials: Bronze, Stainless Steel, Ryton/Polysulfil Plastic. Impellers are Teflon plastic. • There are many motor options available Including AC, DC and High Speed versions for added flow.   March Pump Mag-Drive Centrifugal Pump Bronze with Base 24VDC High Speed 7.5GPM 1/2"MPT Ports  

March 809 815 Series Mag-Drive Centrifugal Pumps Bronze Center Inlet 115V 4.5GPM   The March MAGNE-BOOST Hydronic hot water booster pumps are a non-self priming unit built to handle liquid transfer in heating and cooling operations. Typical applications include home heating systems, solar heating systems, heat recovery systems and recirculating water in domestic and commercial hot water tanks. These pumps are not food rated. • Brewery pump - the March 809 and 815 series of pumps are commonly used by Home Brewers and Breweries. • Maximum liquid temperature for the 809 and 815 series is 250 F. • Port configurations include in-line and center inlet with side discharge. • Construction materials: Bronze, Stainless Steel, Ryton/Polysulfil Plastic. Impellers are Teflon plastic. • There are many motor options available Including AC, DC and High Speed versions for added flow.     March Pump Mag-Drive Centrifugal Pump Bronze Center Inlet 115V 4.5GPM 3/4"MPT Inlet, 1/2"MPT Outlet  

March Mag-Drive Centrifugal Pumps Bronze Center Inlet 12VDC 5.5GPM     The March MAGNE-BOOST Hydronic hot water booster pumps are a non-self priming unit built to handle liquid transfer in heating and cooling operations. Typical applications include home heating systems, solar heating systems, heat recovery systems and recirculating water in domestic and commercial hot water tanks. These pumps are not food rated. • Brewery pump - the March 809 and 815 series of pumps are commonly used by Home Brewers and Breweries. • Maximum liquid temperature for the 809 and 815 series is 250 F. • Port configurations include in-line and center inlet with side discharge. • Construction materials: Bronze, Stainless Steel, Ryton/Polysulfil Plastic. Impellers are Teflon plastic. • There are many motor options available Including AC, DC and High Speed versions for added flow.     March Pump Mag-Drive Centrifugal Pump Bronze Center Inlet 12VDC 5.5GPM 3/4"MPT Inlet, 1/2"MPT Outlet  

March Mag-Drive Centrifugal Pumps Bronze 115V High Speed 4.5GPM     The March MAGNE-BOOST Hydronic hot water booster pumps are a non-self priming unit built to handle liquid transfer in heating and cooling operations. Typical applications include home heating systems, solar heating systems, heat recovery systems and recirculating water in domestic and commercial hot water tanks. These pumps are not food rated. • Brewery pump - the March 809 and 815 series of pumps are commonly used by Home Brewers and Breweries. • Maximum liquid temperature for the 809 and 815 series is 250 F. • Port configurations include in-line and center inlet with side discharge. • Construction materials: Bronze, Stainless Steel, Ryton/Polysulfil Plastic. Impellers are Teflon plastic. • There are many motor options available Including AC, DC and High Speed versions for added flow.   March Pump Mag-Drive Centrifugal Pump Bronze Center Inlet 115V High Speed 4.5GPM 3/4"MPT Inlet, 1/2"MPT Outlet  

March Mag-Drive Centrifugal Pump Plastic 230V Hi Speed  Beer Pump The March MAGNE-BOOST Hydronic hot water booster pumps are a non-self priming unit built to handle liquid transfer in heating and cooling operations. Typical applications include home heating systems, solar heating systems, heat recovery systems and recirculating water in domestic and commercial hot water tanks. These pumps are not food rated. • Brewery pump - the March 809 and 815 series of pumps are commonly used by Home Brewers and Breweries. • Maximum liquid temperature for the 809 and 815 series is 250 F. • Port configurations include in-line and center inlet with side discharge. • Construction materials: Bronze, Stainless Steel, Ryton/Polysulfil Plastic. Impellers are Teflon plastic. • There are many motor options available Including AC, DC and High Speed versions for added flow.   Unit System 60Hz 50Hz Max Flow 6 GPM 18.9 LPM Max Head 12.1 FT 2.5 M Power .04 HP .029 KW Electrical 230V 50/60HZ     Type Centrifugal Mag Drive Inlet 1/2"MPT Outlet 1/2"MPT Wet End Polysulfone (Front Housing), Stainless Steel (Rear Housing and Shaft), Teflon (Thrust Washer), Silicone (O-Ring), Ryton/Teflon/Glass (Impeller) Can handle liquids of 250F Materials are FDA Food Compliant With 6 Foot Cord and Plug Components are UL Recognized American Made          

March 140 Series Mag-Drive Centrifugal Pumps     • Use the compact Series 140 pumps where maximum flow with minimal pressure is desired. Maximum flow is 12.5 GPM (55 LPM) and maximum head is 11.5 ft. (2.5m) • Series 140 pumps use Open Frame Skeleton Type Motors or 1/20 HP (.037 kw), 2900 rpm 115 volt air-cooled motors. • Materials used are glass-filled polypropylene, Buna N rubber, ceramic, Ryton®, Teflon® and Viton®. • Maximum Liquid Temperature is 190 degrees F     March Pump Mag-Drive Centrifugal Pump 230V Open Frame Skeleton Motor 12.5GPM 1 1/8" Hose Inlet, 7/8" Hose Outlet  

March Mag-Drive Centrifugal Pump w/Ports W/115V Mtr   • March MDX pumps can deliver a maximum flow of 6.0 GPM (22 LPM), are capable of serving applications with a maximum head of 7 ft. (1.6m) Fittings are for hose connections. • Applications include coffee dispensers, aquariums, bio-medical, dryers, ice makers, electrostatic painting, photographic processing, and vending equipment. • The plastic parts are molded out of glass filled polypropylene. The spindle housing is molded carbon filled PVDF plastic. The O-rings are Buna N rubber. The magnet is a glazed ceramic. • The motors are 115 volt, 1750 RPM, 50/60 Hz, 1 phase A.C. 230 volt motors are available. Motors are all thermal overload protected and are UL recognized     March Pump Mag-Drive Centrifugal Pump 115V Air Cooled 5.5GPM 1/2" Hose Ports

Applications for the 809-BR Magnetic Drive Pump include hot water systems and solar heating.    March Pump's industrial 809-BR is an American seal-less centrifugal magnetic drive pump ideal for applications such as hot water systems. It is capable of generating a maximum flow of 4.5 gallons per minute at 0.5 feet, and its maximum head is 4.3 Feet (or around 1.8PSI). The standard wet end (the materials that come into contact with the solution) is composed of Bronze, Stainless Steel, Teflon, Silicone and Ryton/Teflon/Glass. The inlet connection is 0.5 male pipe thread, and the outlet is 0.5 inch male pipe thread. The standard motor is a 1 Phase 115V or 230V 0.01 Horsepower fan cooled motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 150PSI, and the maximum liquid temperature is 250 Fahrenheit or 121 Celsius.     Unit System 60Hz 50Hz Max Flow 4.5 GPM 10.3 LPM Max Head 4.3 FT .92 M Power .01 HP .007 KW Electrical 115V 50/60HZ or 230V 50/60HZ     Type Centrifugal Mag Drive Inlet 1/2"MPT Outlet 1/2"MPT Wet End Bronze (Front Housing), Stainless Steel (Rear Housing, Shaft), Teflon (Thrust Washer), Silicone (O-Ring), Ryton/Teflon/Glass (Impeller)