March 1A-MD-1/2 Mag Drive Pump March Pump's industrial 1A-MD-1/2 is an American submersible seal-less centrifugal magnetic drive pump. It is capable of generating a maximum flow of 3 gallons per minute at 0.25 feet, and its maximum head is 4.5 Feet (or around 2PSI).  The 1A-MD-1/2 pump may be used submerged or not submerged. The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Buna N, Nylon, Carbon/Teflon, and Stainless Steel.  When submerged, Epoxy, Noryl, and the SJT Cord are also in contact with the solution. The inlet connection is 1/2 inch smooth, and the outlet is 1/2 inch smooth. The standard motor is a 1 Phase 230V 0.005 Horsepower motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheit or 160 Celsius in open air, or 87 Fahrenheit or 71 Celsius if submerged. The March 1A-MD-1/2 centrifugal magnetic drive pump is capable of handling fresh water, salt water, and mild chemicals. To determine if the March 1A-MD-1/2 is suitable for your application, please contact March Pump.   Perfect for Applications Including Applications for the 1A-MD-1/2 Magnetic Drive Pump include chemical transfer, photographic processing equipment, refrigeration systems, and water displays.   Great for Chemicals Including The 1A-MD-1/2 has pumped Acetone, Ammonium Chloride, Ammonium Chloride, Ammonium Hydroxide, Citric Acid, Ethylene Glycol, Magnesium Nitrate, Potassium Carbonate, Sodium Borate, Fresh Water, Salt Water, and many more chemicals.   Inlet: 1/2"OD Outlet: 1/2"OD Wet End: Polypropylene (Front Housing, Rear Housing, Impeller), Buna N (O-Ring), Carbon/Teflon (Thrust Washer), 316 Stainless Steel (Shaft) Uses:Submersible or Open Air When submerged, the following is also in contact with the solutionEpoxy, Noryl, SJT Cord   P/N 0115-0007-0700 (230V)

March TE-5.5C-MD 1 Phase Mag Drive Pump with Explosion Proof Motor   Applications for the TE-5.5C-MD Magnetic Drive Pump include chemical recirculation, chemical transfer, refrigerators, scrubber systems, detergent mixers, computer cooling, carbon arc furnace cooling, silver recovery systems, and marine air conditioners.     March Pump's industrial TE-5.5C-MD is an American seal-less centrifugal magnetic drive pump ideal for applications such as chemical recirculation, chemical transfer, and scrubber systems. It is capable of generating a maximum flow of 30 gallons per minute at 11 feet, and its maximum head is 41 Feet (or around 18PSI). The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Viton, Ryton/Teflon/Carbon, and Ceramic. The inlet connection is 1 inch female pipe thread, and the outlet is 0.75 inch male pipe thread. The standard motor is a 1 Phase 115/230V or 3 Phase 230/460V 0.33 Horsepower totally enclosed fan cooled motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheit or 87 Celsius. The March TE-5.5C-MD centrifugal magnetic drive pump is capable of handling mildly or highly corrosive chemicals, acids, and solvents.     Unit System 60Hz 50Hz Max Flow 30 GPM 102 LPM Max Head 41 FT 9 M Power .33 HP .248 KW Electrical 1PH 115/230V                  3PH 230/460V 50/60HZ   Type Centrifugal Mag Drive Inlet 1"FPT Outlet 3/4"MPT Wet End Polypropylene (Front and Rear Housing, Impeller), Viton (O-Ring), Ceramic (Shaft, Thrust Washers) Motor Options Explosion Proof

Applications for the MDXT-3 Magnetic Drive Pump include etching equipment, photographic processing equipment, ice flakers, plate processors, and marine air conditioning.    March Pump's industrial MDXT-3 is an American seal-less centrifugal magnetic drive pump ideal for applications such as chemical recirculation and chemical transfer. It is capable of generating a maximum flow of 8.5 gallons per minute at 4 feet, and its maximum head is 19 Feet (or around 8PSI). The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Buna N, Ceramic, and Ceramic Magnet. The inlet connection is 0.5 inch female pipe thread, and the outlet is 0.375 inch female pipe thread. The standard motor is a 1 Phase 115V or 230V 0.04 Horsepower fan cooled motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheit or 87 Celsius. The March MDXT-3 centrifugal magnetic drive pump is capable of handling mildly or highly corrosive chemicals, acids, and solvents.     Unit System 60Hz 50Hz Max Flow 8.5 GPM 30 LPM Max Head 19 FT 4 M Power .04 HP .029 KW Electrical 115V 50/60HZ or 230V 50/60HZ     Type Centrifugal Mag Drive Inlet 1/2"FPT Outlet 3/8"FPT Wet End Polypropylene (Front and Rear Housing, Impeller), Ceramic (Shaft, Thrust Washer), Buna N (O-Ring), Ceramic Magnet  

March 1A-MD-1/2 Mag Drive Pump March Pump's industrial 1A-MD-1/2 is an American submersible seal-less centrifugal magnetic drive pump. It is capable of generating a maximum flow of 3 gallons per minute at 0.25 feet, and its maximum head is 4.5 Feet (or around 2PSI).  The 1A-MD-1/2 pump may be used submerged or not submerged. The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Buna N, Nylon, Carbon/Teflon, and Stainless Steel.  When submerged, Epoxy, Noryl, and the SJT Cord are also in contact with the solution. The inlet connection is 1/2 inch smooth, and the outlet is 1/2 inch smooth. The standard motor is a 1 Phase 115V 0.005 Horsepower motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheit or 160 Celsius in open air, or 87 Fahrenheit or 71 Celsius if submerged. The March 1A-MD-1/2 centrifugal magnetic drive pump is capable of handling fresh water, salt water, and mild chemicals. To determine if the March 1A-MD-1/2 is suitable for your application, please contact March Pump.   Perfect for Applications Including Applications for the 1A-MD-1/2 Magnetic Drive Pump include chemical transfer, photographic processing equipment, refrigeration systems, and water displays.   Great for Chemicals Including The 1A-MD-1/2 has pumped Acetone, Ammonium Chloride, Ammonium Chloride, Ammonium Hydroxide, Citric Acid, Ethylene Glycol, Magnesium Nitrate, Potassium Carbonate, Sodium Borate, Fresh Water, Salt Water, and many more chemicals.   Inlet: 1/2"OD Outlet: 1/2"OD Wet End: Polypropylene (Front Housing, Rear Housing, Impeller), Buna N (O-Ring), Carbon/Teflon (Thrust Washer), 316 Stainless Steel (Shaft) Uses:Submersible or Open Air When submerged, the following is also in contact with the solutionEpoxy, Noryl, SJT Cord   P/N:0115-0007-0200 (115V)

  Applications for the March 821-CI Magnetic Drive Pump include hot water and hot oil systems.    March Pump's industrial 821-CI is an American seal-less centrifugal magnetic drive pump ideal for applications such as hot water systems. It is capable of generating a maximum flow of 22 gallons per minute at 2.5 feet, and its maximum head is 8.5 Feet (or around 3.6PSI). The standard wet end (the materials that come into contact with the solution) is composed of Cast Iron, Stainless Steel, Ryton, Ceramic, Carbon, and Nitrile/Fibre. The inlet connection is a flange, and the outlet is a flange. The standard motor is a 1 Phase 115V or 230V 0.05 Horsepower fan cooled motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 150PSI, and the maximum liquid temperature is 250 Fahrenheit or 121 Celsius.     Unit System 60Hz 50Hz Max Flow 22 GPM 75.7 LPM Max Head 8.5 FT 1.6 M Power .05 HP .037 KW Electrical 115V 50/60HZ   or   230V 50/60HZ   Type Centrifugal Mag Drive Inlet Flange Outlet Flange Wet End Cast Iron (Front Housing), Stainless Steel (Rear Housing, Shaft), Ryton (Impeller), Ceramic (Thrust Washer), Carbon (Bushing), Nitrile/Fibre (Gasket)

March MDXT-3 Magnetic Drive Pump Applications for the include etching equipment, photographic processing equipment, ice flakers, plate processors, and marine air conditioning.   March Pump's industrial MDXT-3 is an American seal-less centrifugal magnetic drive pump ideal for applications such as chemical recirculation and chemical transfer. It is capable of generating a maximum flow of 8.5 gallons per minute at ;4 feet, and its maximum head is 19 Feet (or around 8PSI). The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Buna N, Ceramic, and Ceramic Magnet. The inlet connection is 0.5 inch female pipe thread, and the outlet is 0.375 inch female pipe thread. The standard motor is a 1 Phase 230V 0.04 Horsepower fan cooled motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheit or 87 Celsius. The March MDXT-3 centrifugal magnetic drive pump is capable of handling mildly or highly corrosive chemicals, acids, and solvents.   The MDXT-3 has pumped has pumped Acetic Acid, Acetone, Ammonium Sulfate, Citric Acid, Ethylene Glycol, Ferric Sulfate, Hydrogen Peroxide, Potassium Hydroxide, Sodium Chloride, Fresh Water, Salt Water, and many more chemicals.   Unit System 60Hz 50Hz Max Flow 8.5 GPM 30 LPM Max Head 19 FT 4 M Power .04 HP .029 KW Electrical 115V 50/60HZ or 230V 50/60HZ   Type Centrifugal Mag Drive Inlet 1/2"FPT Outlet 3/8"FPT Wet End Polypropylene (Front and Rear Housing, Impeller), Ceramic (Shaft, Thrust Washer), Buna N (O-Ring), Ceramic Magnet

Little Giant 3-MD-SC Mag-Drive Pump 581513 Little Giant 3-MD-SC 230V Magnetic Drive Pump This Pump will handle up to a 48,000 BTU Air Conditioner Motor 230 Volt 60 Hz 1/12 HP Open Fan Cooled Motor, 750 GPH at 1 Foot Head, Shutoff Head 21.9 Feet, Inlet: 3/4" FNPT, Outlet: 1/2" MNPT, Polypropylene Body, Fluid Temperature Up to 150F (66C), UR/C-CSA Listed, 6 Foot Power Cord   581513 Magnetically driven pump for semi-corrosive chemicals and solutions. The MD-SC Series features leakproof, seal-less magnetic drives and are designed for in-line, non-submersed use

March 893-06 Magnetic Drive Pump for Marine Refrigeration and Fountains. March Pump's industrial 893-06 is an American submersible seal-less centrifugal magnetic drive pump ideal for applications such as marine equipment. It is capable of generating a maximum flow of 2.7 gallons per minute at 1 foot, and its maximum head is 10.6 Feet (or around 4.5PSI).  The 893-06 must be used submerged. The standard wet end (the materials that come into contact with the solution) is composed of Noryl, Nylon, Carbon/Teflon, Buna N, Stainless Steel, and Ceramic Magnet.  When submerged Epoxy, Delrin, and the motor leads are also in contact with the solution. The inlet connection is 0.375 inch female pipe thread, and the outlet is 0.375 inch smooth. The standard motor is a 0.006 Horsepower DC Brushtype Motor, available in 24 Volts.  The 24 Volt Motor has an operating range from 0 to 26 Volts.  The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 160 Fahrenheit or 71 Celsius. The March 893-06 centrifugal magnetic drive pump is capable of handling mild corrosive chemicals, acids, and solvents.   Max Flow: 2.7 GPM or 11 LPM Max Head:10.6 FT or 3.3 M Power:.006 HP or .004 KW Electrical: 24V Range 0-26V Submersible: Yes    Type: Centrifugal Mag Drive Inlet: 3/8"FPT Outlet: 3/8"OD Wet End: Noryl (Front and Rear Housings), Nylon (Impeller), Carbon/Teflon (Thrust Washer), Buna N (O-Ring), 316 Stainless Steel (Shaft), Ceramic Magnet Uses: Must be submerged When submerged, the following is also in contact with the solution: Epoxy, Delrin and Motor Leads

March 815-BR Magnetic Drive Pump for Hot Water Systems and Solar Heating March Pump's industrial 815-BR is an American seal-less centrifugal magnetic drive pump ideal for applications such as hot water systems. It is capable of generating a maximum flow of 7 gallons per minute at 5 feet, and its maximum head is 18.6 Feet (or around 8PSI). The standard wet end (the materials that come into contact with the solution) is composed of Bronze, Stainless Steel, Teflon, Silicone and Ryton/Teflon/Glass. The inlet connection is 0.5 male pipe thread, and the outlet is 0.5 inch male pipe thread. The standard motor is a 1 Phase 115V or 230V 0.04 Horsepower fan cooled motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 150PSI, and the maximum liquid temperature is 250 Fahrenheit or 121 Celsius.   Max Flow: 7 GPM or 22.7 LPM Max Head: 18.6 FT or 4.1 M Power: .04 HP or .029 KW Electrical: 115V 50/60HZ or 230V 50/60HZ   Type: Centrifugal Mag Drive Inlet: 1/2"MPT Outlet: 1/2"MPT Wet End: Bronze (Front Housing), Stainless Steel (Rear Housing and Shaft), Teflon (Thrust Washer), Silicone (O-Ring), Ryton/Teflon/Glass (Impeller)

Applications for the 809-BR Magnetic Drive Pump include hot water systems and solar heating.    March Pump's industrial 809-BR is an American seal-less centrifugal magnetic drive pump ideal for applications such as hot water systems. It is capable of generating a maximum flow of 4.5 gallons per minute at 0.5 feet, and its maximum head is 4.3 Feet (or around 1.8PSI). The standard wet end (the materials that come into contact with the solution) is composed of Bronze, Stainless Steel, Teflon, Silicone and Ryton/Teflon/Glass. The inlet connection is 0.5 male pipe thread, and the outlet is 0.5 inch male pipe thread. The standard motor is a 1 Phase 115V or 230V 0.01 Horsepower fan cooled motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 150PSI, and the maximum liquid temperature is 250 Fahrenheit or 121 Celsius.     Unit System 60Hz 50Hz Max Flow 4.5 GPM 10.3 LPM Max Head 4.3 FT .92 M Power .01 HP .007 KW Electrical 115V 50/60HZ or 230V 50/60HZ     Type Centrifugal Mag Drive Inlet 1/2"MPT Outlet 1/2"MPT Wet End Bronze (Front Housing), Stainless Steel (Rear Housing, Shaft), Teflon (Thrust Washer), Silicone (O-Ring), Ryton/Teflon/Glass (Impeller)

March 809 PL Magnetic Drive Centrifugal Pump The March 809-PL is used to pump Cutting Oils, Ethylene Glycol, Hot Water, Hot Wort and Salt Water March Pump's industrial 809-PL is an American seal-less centrifugal magnetic drive pump ideal for applications such as home brewing and hot water systems. It is capable of generating a maximum flow of 4.5 gallons per minute at 0.5 feet, and its maximum head is 4.3 Feet (or around 1.8PSI). The standard wet end (the materials that come into contact with the solution) is composed of Polysulfone, Stainless Steel, Teflon, Silicone and Ryton/Teflon/Glass. The inlet connection is 0.5 male pipe thread, and the outlet is 0.5 inch male pipe thread. The standard motor is a 1 Phase 115V or 230V 0.01 Horsepower fan cooled motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 50 PSI, and the maximum liquid temperature is 250 Fahrenheit or 121 Celsius Unit System 60Hz Max Flow 4.5 GPM Max Head 4.3 FT Power .01 HP Electrical 115V 60HZ      Type Centrifugal Mag Drive Inlet 1/2"MPT Outlet 1/2"MPT Wet End Polysulfone (Front Housing), Stainless Steel (Rear Housing, Shaft), Teflon (Thrust Washer), Silicone (O-Ring), Ryton/Teflon/Glass (Impeller)

March 815-BR Magnetic Drive Pump for Hot Water systems and Solar Heating. March Pump's industrial 815-BR is an American seal-less centrifugal magnetic drive pump ideal for applications such as hot water systems. It is capable of generating a maximum flow of 7 gallons per minute at 5 feet, and its maximum head is 18.6 Feet (or around 8PSI). The standard wet end (the materials that come into contact with the solution) is composed of Bronze, Stainless Steel, Teflon, Silicone and Ryton/Teflon/Glass. The inlet connection is 0.5 male pipe thread, and the outlet is 0.5 inch male pipe thread. The standard motor is a 1 Phase 115V or 230V 0.04 Horsepower fan cooled motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 150PSI, and the maximum liquid temperature is 250 Fahrenheit or 121 Celsius.   Max Flow: 7 GPM or 22.7 LPM Max Head: 18.6 FT or 4.1 M Power: .04 HP or.029 KW Electrical: 115V 50/60HZ or 230V 50/60HZ     Type: Magnetic Drive Centrifugal Pump Inlet: 1/2"MPT Outlet: 1/2"MPT Wet End: Bronze (Front Housing), Stainless Steel (Rear Housing and Shaft), Teflon (Thrust Washer), Silicone (O-Ring), Ryton/Teflon/Glass (Impeller)

Little Giant Pump 584604 Little Giant TE-5-MD-HC Magnetic Drive Pump Motor 115/230 Volt 50/60 Hz 1/8 HP Totally Enclosed Fan Cooled Motor, 1200 GPH at 1 Foot Head, Shutoff Head 29.3 Feet, Inlet: 1" FNPT, Outlet: 1/2" MNPT, Ryton Body, Fluid Temperature Up to 200F (93C), UR/C-CSA Listed, 6 Foot Power Cord- Not Installed   584604 Magnetically driven pumps for circulation of highly corrosive acids, alkalis, solvents, brine, plating solutions, sterile solutions, and other highly corrosive chemicals and solutions. The MD-HC Series features leakproof, seal-less magnetic drives and are designed for in-line, non-submersed use

Little Giant Pump 115/208-230 Volts 587010 Little Giant TE-7-MD-HC Magnetic Drive Pump The motor is 115/208-230 Volt 50/60 Hz 3/4 HP Totally Enclosed Fan Cooled Motor, 3180 GPH at 1 Foot Head, Shutoff Head 58.9 Feet, Inlet: 1-1/2" FNPT, Outlet: 1" MNPT, Ryton Body, Fluid Temperature Up to 200F (93C), UR/C-CSA Listed, With Conduit Box   587010 Magnetically driven pump for circulation of highly corrosive acids, alkalis, solvents, brine, plating solutions, sterile solutions, and other highly corrosive chemicals and solutions. The MD-HC Series features leakproof, seal-less magnetic drives and are designed for in-line, non-submersed use

March LC-3CP-MD Mag Drive Pump W/115V Mtr