Securely seals universal and exhaust bellows. Resistant to oil, grease, gasoline and water. Replaces Mercury 92-86166Q1.

Polish - Paste - 1.76 oz. Tube Part #: BU 03511 One product, Many uses. Metal, Plastic, Fiberglass, Glass, Corian... This is the Flitz signature product. A concentrated cream, Flitz Polish is unsurpassed in its ability to Clean, Polish, Deoxidize and Protect. Features: Tough, durable protection Non-abrasive formula Non-toxic Non-flammable USDA authorized Protects up to 6 months in fresh water, up to 3 months in salt water Use on: Brass Copper Silverplate Sterling Silver Chrome Stainless Steel Nickel Bronze Solid Gold Aluminum Annodized Aluminum Beryllium Magnesium Platinum Pewter Factory Hot Gun Bluing Painted Surfaces Formica Cultured Marble Corian Glass Plexiglas Plastics Fiberglass Eisenglass Armatel Easily Removes: Tarnish Rust Water Stains Chalking Lime Deposits Heat Discoloration Lead & Powder Residue Oxidation Bugs Tar Oil Fingerprints Tree Sap Bird Droppings Graffiti Dyes Black Streaks/Scuff Marks Not for: Electroplated finishes

Sierra Aqua Vue and metal collection bowl separator filters allow water to be drained from the filter to extend service life. Use the Aqua Vue collection bowl for outboard, above deck installations. USCG regulations require the use of the flame resistant metal collection bowl below deck. Kit contains 2 brass pipe plugs. Display packaged.

Sierra fuel water separators remove over 98.8% of emulsified water from gasoline. All filters flow at 90 GPH. Kits include 2 pipe plugs. Display packaged.

Sierra fuel water separators remove over 98.8% of emulsified water from gasoline. All filters flow at 90 GPH. Kits include 2 pipe plugs. Display packaged.

Water temperature sending unit, 1/2" -14 NPT threads. Replaces: Mercruiser 97258A1, OMC/Cobra 171960, Crusader 700427

3" Shaft - 5-1/2" Stern Tube The PSS Shaft Seal is the #1 selling marine mechanical seal worldwide and is installed as standard equipment by many of the worlds most reputable boat builders and boat yards. The PSS Shaft Seal is also recognized as the premiere retrofit (aftermarket) seal on the world market. Boat builders and boat yards recognize the advantages and value of installing the PSS as it eliminates the maintenance, constant adjustment & cost associated with traditional packing type glands. Aside from these benefits, the PSS Shaft Seal helps to eliminate water in the bilge (100% water tight) & wear to the propeller shaft.  How Does it Work? 1. Two nitrile o-rings seal the stainless steel rotor to the shaft and will not experience wear. 2. A primary set screw and a backup set screw (2 sets) are used to secure the stainless steel rotor to the shaft. 3. A seal is created between the two flat surfaces of the carbon stator and the stainless steel rotor. 4. Water is fed into the PSS Shaft Seal for cooling/lubricating the seal faces on high speed vessels. 5. The stationary carbon stator is attached to the nitrile bellow, which is attached to the stern tube (shaft log). Rotor The PSS stainless steel rotor is slid down the shaft and is secured to the shaft with set screws at 90° for maximum holding power. Precision tolerances are maintained by computer controlled lathes. The faces have a number 9 micro finish and are perpendicular to the bore to prevent run-out as the collar rotates. The carbon graphite stator will polish the face of the rotor during the first few minutes of operation. The stainless steel rotor should not need to be replaced under normal operating conditions. The stainless steel rotor used on the PSS Type A Shaft Seal is made from 316L stainless steel.  Carbon Stator The high density, resin impregnated carbon/graphite stator is a composite that is first mixed, molded and then formed under pressure. The blanks are then baked, machined and lapped. The face of our carbon is finished to a flatness of 4 helium light bands (measured .000044" of variation over entire lapped surface). The grade of carbon used in the PSS has an operating temperature over 500° Fahrenheit (+260° Celsius), and cannot melt if the seal runs dry, unlike a rubber lip seal or plastic face seal. The high density of the carbon greatly increases the longevity and wear resistance. Several commercial vessels have recorded over 40,000 (over 4-1/2 years of continuous operation) engine hours on the same, original components. The carbon should not need to be replaced under normal operating conditions.  Bellow The PSS Type A Shaft Seal bellow is made from rubber (Nitrile), and has a temperature rating of -25°F to +225°F (-31°C to +107°C). Nitrile is known for its resistance to weathering. Nitrile rubber is exceptionally resistant to oils and non-polar solvents. It also offers good gas impermeability, abrasion resistance, and better thermal stability than most general purpose elastomers.  Hose Barb For high speed vessels it is required that a positive water supply be plumbed to the PSS Shaft Seal for the purpose of lubricating and cooling the seal faces. There are many sources of water supply, review the PSS Shaft Seal Installation Instructions for more information and note all plumbing must follow the standards and practices of proper boat plumbing. In most cases a slow speed boat that does not have a bearing the shaft log does not require positive water feed and can simply be "vented". Ideally the vent line will be run at least 2-3 feet above the water line and is close to the center line as possible to ensure the vent hose is never below the water line, even if the boat heels. Review the PSS Shaft Seal Installation Instructions for more details on venting the seal.

Ampco Pumps P1GXPIP-1/2 Plastic Cap Plug

BURKS T350G6-1 1/2, CENTRIFUGAL PUMP 3PH 5HP TEFC Close Coupled, 60 Hz, Three Phase, 3500 RPM, 5 Horsepower, TEFC Motor Enclosure, Frame Size 184JM   UNSPSC Code: 40150000

Ampco Pumps KC2 2 1/2 X 2 Fluid End Nialbz 5.00" Trim

Bosworth 400-H-Ale-1/2"F Guzzler 1/2" Hand Pmp,Tappd   Bosworth Hand Diaphragm Pump Guzzler Delrin, .44Qt per Stroke, 1/2" Female Threaded Ports, Buna Flapper Valves and Diaphragm, Horizontal Handle with Epoxy Coated Aluminum Clamp Ring for Durability

March 893-11-1/2 +Pump/12V Mtr 1/2"Ports This item is 'build to order'. Please contact us for lead time.

March TE-7S-MD 1.5hp 3 phase March Pump's industrial TE-7S-MD is an American seal-less centrifugal magnetic drive pump ideal for applications such as chemical recirculation, chemical transfer, and scrubber systems. It is capable of generating a maximum flow of 53 gallons per minute at 10 feet, and its maximum head is 57.5 Feet (or around 25PSI). The standard wet end (the materials that come into contact with the solution) is composed of 316 Stainless Steel, Viton, Carbon, and Ceramic. The inlet connection is 1-1/2 inch female pipe thread, and the outlet is 1 inch male pipe thread. There are two standard motors. The first is a 1 Phase 60 hertz 115/208/230V and 50 hertz 110/220V 1 horsepower totally enclosed fan cooled motor.  The second is a 3 Phase 60 hertz 208/230/460V and 50 hertz 190/380V 1 horsepower totally enclosed fan cooled motor. There are performance differences between the hertz options. The maximum internal pressure the pump can tolerate is 200PSI, and the maximum liquid temperature is 250 Fahrenheit or 121 Celsius. The March TE-7S-MD centrifugal magnetic drive pump is capable of handling mildly or highly corrosive chemicals, acids, and solvents. To determine if the March TE-7S-MD is suitable for your application, please contact March Pump.   Perfect for Applications Including; Applications for the TE-7S-MD Magnetic Drive Pump include chemical recirculation, chemical transfer, refrigerators, scrubber systems, detergent mixers, computer cooling, carbon arc furnace cooling, silver recovery systems, and marine air conditioners.   Great for Chemicals Including The TE-7S-MD has pumped Acetic Acid, Citric Acid, Ethylene Glycol, Formaldehyde, Potassium Chloride, Potassium Hydroxide, Sodium Chloride,  Sodium Hydroxide (Caustic Soda), Fresh Water, Salt Water, and many more chemicals.     Unit 60HZ 50HZ System US Metric US Metric Max Flow 53 GPM 200 LPM 47.5 GPM 180 LPM Max Head 57.5 FT 17.5 M 39.4 FT 12 M Power 1 HP .745 KW 1 HP .745 KW Electrical 1PH 115/208/230V 60HZ, 110/220V 50HZ or 3PH 208/230/460V 60HZ, 190/380V 50HZ On 50HZ, the Single Phase Motor is rated for 1 horsepower or 0.7457 kilowatts. On 50HZ, the Three Phase Motor is rated for 1 horsepower or 0.7457 kilowatts.     Type Centrifugal Mag Drive Inlet 1-1/2"FPT Outlet 1"MPT Wet End 316 Stainless Steel (Front Housing, Rear Housing, Impeller), Viton (O-Ring), Ceramic (Shaft, Thrust Washers), Carbon (Bushing) Motor Options Available in 1HP, 1.5HP, 1HP Explosion Proof or 1.5HP Explosion Proof P/N 0155-0173-0300 (1 Phase 1HP) with Metal Motor Bracket P/N 0155-0174-0300 (3 Phase 1HP) with Metal Motor Bracket P/N 0155-0036-0300 (3 Phase 1.5HP) with Metal Motor Bracket P/N 0155-0285-0100 (1 Phase 1HP) with Plastic Motor Bracket P/N 0155-0286-0100 (3 Phase 1HP) with Plastic Motor Bracket P/N 0155-0287-0100 (3 Phase 1.5HP) with Plastic Motor Bracket  

Fill-Rite 901-1 1/2 Flow Meter   Fill-Rite Flow Meter 6-40GPM Nickel Plated 1 1/2”FNPT Ports

Fill-Rite 901-N-1 1/2 901 Meter Nickel Plated 1.5   Fill-Rite Flow Meter 6-40GPM 1 1/2"FNPT Ports