Ignitions for Yamaha outboards.

Sierra fuel pumps for Yamaha outboards.

Applications for the March 893-08 Magnetic Drive Pump include computer cooling, photographic processing equipment, refrigeration systems, and water displays.    March Pump's industrial 893-08  is an American seal-less centrifugal magnetic drive pump ideal for applications such as chemical recirculation, chemical transfer, and heat transfer. It is capable of generating a maximum flow of 2.7 gallons per minute at 1 foot, and its maximum head is 10.6 Feet (or around 4.5PSI). The standard wet end (the materials that come into contact with the solution) is composed of Noryl, Nylon, Carbon/Teflon, Buna N, Stainless Steel, and Ceramic Magnet. The inlet connection is 0.375 inch female pipe thread, and the outlet is 0.375 inch smooth. The standard motor is a 0.006 Horsepower DC Brushless Motor, available in 24 Volts.  The 24 Volt Motor has an operating range from 12 to 28 Volts.  The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheit or 87 Celsius. The March 893-08 centrifugal magnetic drive pump is capable of handling mildly or highly corrosive chemicals, acids, and solvents.      Max Flow 2.7 GPM 11 LPM Max Head 10.6 FT 3.3 M Power .006 HP .004 KW Electrical 24V Range 12-28   Type Centrifugal Mag Drive Inlet 3/8"FPT Outlet 3/8"OD Wet End Noryl (Front and Rear Housings), Nylon (Impeller), Carbon/Teflon (Thrust Washer), Buna N (O-Ring), 316 Stainless Steel (Shaft), Ceramic Magnet

Sierra cylinder block gaskets.

NXL-M4 Full Range 4 Channel IPX5 Marine Grade Amplifier - 150 x 4W @ 4-Ohm Designed for intense sessions that keep the party boat rocking all night long; the NXL-M4 is DS18’s high-quality, powerful amplifier for the wave runner looking for a big sound with a small footprint! As a Class D Digital amplifier, the NXL-M4 uses a direct insert speaker and power terminals significantly smaller than your average amplifier, making it the perfect size for any vehicle’s custom build: but, what it lacks in size it makes up for in power. The NXL-M4 handles 150W x 4CH @ 4 Ohms; 230W x 4CH @ 2 Ohms; and 440W x 2CH @ 4 Ohms Bridge of RMS Power and 1800W Peak Power. Get clean, well-defined sound for with enough features (Fully Variable Bass Boost, Low Pass Filter, and High Pass Filter) to tune your music perfectly for optimal audio enjoyment! This full-range amplifier handles all speakers insanely well and has the features to make sure they play the way you want them to! This amplifier is tough enough to stand up to the worst the waves throw at you! All controls are guarded by high-strength front covers that guarantee impenetrable defense against the elements; coated 4-layer PCB helps prevent corrosion caused by salt water; and Voltage, Thermal, and Short Circuit Protection for easy monitoring of your power levels. Order the NXL-M4 for insane power out on the water! Features: Hardware resistant to corrosion and UV Protection Coated 4 Layers PCB to prevent corrosion IPX5 Water Resistance Grade High Level Input For Radio Use Front cover to keep the controls safe to the elements LED Clip Indicator to easier adjustment Stable and Reliable Class D Circuit Design Sound Quality Verification Using AP Instruments Direct Insert Power and Speaker Terminals Short Circuit, Thermal, and Voltage Protection Technical Specifications: Number of Channels - 4 Frequency Response - 20Hz - 20KHz  2 Ohm RMS Power Per Channel - 4 x 230W  4 Ohm RMS Power Per Channel - 4 x 150W  4 Ohm RMS Power Bridge Channel - 2 x 440W  Signal-to-Noise Ratio - >90dB  Product Dimensions: (L x W x H) - 9.6" x 4.5" x 1.7" *Sold as an Individual

Tilt Trim Motor for Yamaha Outboard Engines 150-250HP, 2011-2021 4-Stroke.

Johnson Raw Water Pump for 4-Cylinder AQ Series Volvo Johnson Seawater Pump fits Early 4-Cylinder Volvo-Penta AQ125, 131, 145 pump for 4-cylinder engines. Replaces Volvo-Penta part # 855578

9 amp stators for 2, 3, 4 and 6 cylinder outboard engines.

9 amp stators for 2, 3, 4 and 6 cylinder outboard engines.

FITS: Yamaha 2004-2015 50/60HP, 4 Stroke, 2-wire connection, 3-bolt mount, ring terminal ends, Includes O-ring.

Replaces points & condensers for true solid state ignition. Uses standard coil, cap and rotor. One-piece, 2-wire hook up. Accurate to withing 1/4° timing accuracy 0 to 6000 RPM range. 18-5298-1 Lobe Sensing Techonology does not require magnetic sleeves.

3 Blade stainless propeller for 25-30 horsepower engines with 10 tooth spline and thru hub exhaust. 3" gear case, Japan origin.

SX 9.5 x 10 Smart Tabs 12-16' Boats with 40lb Actuators - 40-80HP - Gunmetal Grey The SX series incorporates all of the fully automatic features of the popular Smart Tabs, in addition to the rust and corrosion-free benefits of molded composite materials. Assembly can be completed in seconds and the installation in a few minutes. The only tools required are a drill with a 3/16" bit and a Phillips screwdriver. Smart Tabs SX provides un-equaled performance and durability with no maintenance in fresh or saltwater. The system can be specifically tuned to maximize the performance of any powerboat, and Tracking Ribs have been added to improve handling at higher speeds. Smart Tabs are a one-of-a-kind trim and stabilizer system that automatically adjusts to the sea conditions, without the need for expensive electric or hydraulic hardware and switches. The system constantly reacts to the water conditions, boat speed, and balance providing a remarkable improvement on any boat. Performance Benefits: Smoother and Faster Acceleration - Great for Skiing 40% less Bow Rise and 35% Lower On Plane Speed - Great for Tubing More Top Speed and No Porpoising or Chine Walking Improves Handling and Smoother Ride In Any Water Improved Fuel Economy (11% +) Assembly & Installation In Minutes: Complete assembly and mounting requires only a drill, a 3/16" bit, and a Phillips screwdriver The Integral design eliminates the need for wrenches All components "lock" together with self-locking clevis pins

March 893-10 Brushless 24V DC Pump Applications for the March 893-10 Magnetic Drive Pump include computer cooling, photographic processing equipment, refrigeration systems, and water displays.   March Pump's industrial 893-10 is an American submersible seal-less centrifugal magnetic drive pump ideal for applications such as chemical recirculation, chemical transfer, and heat transfer. It is capable of generating a maximum flow of 2.7 gallons per minute at 1 foot, and its maximum head is 10.6 Feet (or around 4.5PSI).  The pump may be used submerged or not submerged. The standard wet end (the materials that come into contact with the solution) is composed of Noryl, Nylon, Carbon/Teflon, Buna N, Stainless Steel, and Ceramic Magnet.  When submerged Epoxy, Delrin, and the motor leads are also in contact with the solution. The inlet connection is 0.375 inch female pipe thread, and the outlet is 0.375 inch smooth. The standard motor is a 0.006 Horsepower DC Brushless Motor, available in 24 Volts.  The 24 Volt Motor has an operating range from 12 to 28 Volts.  The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheit or 87 Celsius when not submerged, or 130 Fahrenheit or 54 Celsius when submerged. The March 893-10 centrifugal magnetic drive pump is capable of handling mildly or highly corrosive chemicals, acids, and solvents.   Max Flow 2.7 GPM 11 LPM Max Head 10.6 FT 3.3 M Power .006 HP .004 KW Electrical 24V Range 12-28V Submersible Yes   Type Centrifugal Mag Drive Inlet 3/8"FPT Outlet 3/8"OD Wet End Noryl (Front and Rear Housings), Nylon (Impeller), Carbon/Teflon (Thrust Washer), Buna N (O-Ring), 316 Stainless Steel (Shaft), Ceramic Magnet Uses Submersible or Open Air When submerged, the following is also in contact with the solution Epoxy, Delrin, Motor Leads    

3 Blade aluminum propeller for 9.9-25 horsepower engines with 10 tooth spline and thru hub exhaust. 3" gear case.