Quick Flush™ Outboard Flush Fitting Kit for Mercury & Yamaha Outboards Provides a quick and easy way to flush any outboard equipped with a flushing port. No more removing the plug and twisting hoses to flush. Replace the plug with the Quick Flush™ and snap the hose on and off. Normal operating water pressure keeps the valve sealed when using engine.  Features: Makes flushing outboard quick and easy Unique previously patented slide valve replaces outboard flushing port plug O-ring seal closes off port when operating engine Quick connect on hose snaps onto valve for flushing No plug to remove and no difficult turning of hose into port Takes the hassle out of flushing your outboard Fits all outboards equipped with a flushing port Kit consists of slide valve, hose quick connector, and washer WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

T-H Marine Supplies T-H Marine produces thousands of products in many categories, including outboard motor mounts, outboard tilt and trim, access hatches, deck plates, lid locks, deck hardware, livewell aeration, plumbing fittings, battery trays, fishing rod holders, boat lights, rigging accessories, trolling motor accessories, pontoon boat parts, and general boat accessories.

Quick Flush Kit for OMC Outboards Provides a quick and easy way to flush any outboard equipped with a flushing port. No more removing the plug and twisting hoses to flush. Replace the plug with the Quick Flush™ and snap the hose on and off. Normal operating water pressure keeps the valve sealed when using engine.  Features: Makes flushing outboard quick and easy Unique previously patented slide valve replaces outboard flushing port plug O-ring seal closes off port when operating engine Quick connect on hose snaps onto valve for flushing No plug to remove and no difficult turning of hose into port Takes the hassle out of flushing your outboard Fits all outboards equipped with a flushing port Kit consists of slide valve, hose quick connector, and washer  WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

WP018 Water Pump Repair Kit for Mercury Outboard Engines This water pump repair kit is designed for specific Mercury outboard engines. Fits: Mercury 9.9 hp 4-stroke outboards Replaces: MERCURY Water Pump Repair Kit 46-99157T2 MERCURY Water Pump Repair Kit 99157A2 MERCURY Water Pump Repair Kit 85098A2 Warranty Information When properly installed, all ARCO products are warrantied against defects in materials and workmanship for 12 months for leisure use and 90 days for commercial or racing applications. Add an extra year of warranty to your rotating electric ARCO product (Tilt/Trim Motors, Alternators, Outboard Starters, and Inboard Starters) when you register your product within 30 days of purchase. You can register your product by visiting arcomarine.com/product-registration.

Motor Stik OutBoard Motor Support Stick - Pair Features: Fits Over Trim Rams Supports Your Outboard While Trailering Takes the Pressure Off of Hydraulic System Most Outboards 150hp and Up Strong Aluminum Tubing with Molded Ends Safe for Salt or Fresh Water Note: Some Yamaha motors have a grease fitting on the port side ram. Use a single Motor Stik™ on the starboard side only in this application. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Steer Stop Outboard Hydraulic Steering Lock Set - 4" T-H Marine developed the first steering stop available for outboard motors and now we've revised that design so it stands apart from imitation and performs better than any other on the market.  With our 4" Steer Stop Outboard Hydraulic Steering Lock in place, boaters can center their outboard motor equipped with hydraulic steering and keep it from wandering when trailering. Similar to the original Steer Stop, units clip onto hydraulic steering rams on either side of outboard to keep engine straight and prevent damage to motor supports. The cord then keeps units together when stowed and aids removal. Additionally, with the new grip built into the design, it is easier than ever to install and remove the Steer Stop Outboard Hydraulic Steering Lock, saving you effort and wear and tear on your hands. Features: Must-know information about the 4" Steer Stop Outboard Hydraulic Steering Lock: Locks hydraulic steering when trailering Fits most steering cylinder rods on outboard engines Snaps over outboards hydraulic steering cylinder rods Helps keep engine centered during transport Protects steering system, outboard, and motor supports Includes cord to connect units for storage and to aid in removal Grip makes it even simpler and easier to put on and take off WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Heat Shrink Terminal Connector Kit *24-Piece Insulates wire connections and waterproof terminals.

Original Equipment Quality Replacement Tilt Trim Motor for Mercury/Mariner Outboards with Design II 3 RAM Replacement outboard tilt trim motor that will fit Mercury/Mariner outboards w/Design II 3 ram, three-wire trim units, Hollow-hex shaft W/AFT FILL RESERVOIR, 3-wire connection, 2-bolt mount, Shaft adaptor, and O-ring included, Ring Terminal Ends.  ARCO advises cleaning all connections: A corroded connection creates resistance, lowering the amperage required to operate the motor. Features: Tilt trim motors are dynamically tested to ensure out-of-the-box performance  Motor shafts induction case hardened at bearing surfaces for superior wear resistance  Epoxy Powder coated for maximum insulation protection Warranty Information: When properly installed, all ARCO products are warrantied against defects in materials and workmanship for 12 months for leisure use and 90 days for commercial or racing applications.  Add an extra year of warranty to your rotating electric ARCO product (Tilt/Trim Motors, Alternators, Outboard Starters, and Inboard Starters) when you register your product within 30 days of purchase. You can register your product by visiting arcomarine.com/product-registration  Replaces: MERCURY Tilt Trim Motor 811628 MERCURY Tilt Trim Motor 828708A1 MERCURY Tilt Trim Motor 878265A6 SIERRA Tilt Trim Motor 18-6774 This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

El Outboard Steering Kit for Up To 150HP Motors 401 Manual Helm with Fitting Kit The heart of the Admiral Series is the HyDrive M402 helm unit. The 7-piston pumps are precision manufactured to standards and tolerances that are second to none. In-built lock valves, which eliminate torque feedback are standard. The light, smooth steering must be experienced to be appreciated. Designed as a complete Do It Yourself installation, everything you need is supplied including detailed instructions. You don’t even have to know anything about hydraulics! The Admiral Series 401 helm units offer improved internal efficiencies and unique assembly design, consolidating HyDrive Engineering‘s position as a world leader in hydraulic boat steering. Two years of design development and testing have resulted in these helms being selected as the standard helm supplied in all HyDrive steering kits. Features: Front-mount design for maximum appeal Improved internal efficiency Brass wheel nut and washer Stainless steel steering wheel shaft - not aluminum Anti-splash filler cap for rough conditions Unique assembly design for ease of service and maximum performance Stainless steel studs, nuts, and washer pre-fitted for convenience Highly efficient non-return valves for non-feedback of helm unit - eliminates all torque from the steering cylinder Ultra 15 Oil Quantity 2 - 1 Liter Bottles Features: For use in HyDrive Skipper and Admiral Series Hydraulic steering systems only Not for use in HyDrive 2000 Series Steering Systems This oil is compatible with HyDrive HF15, but should not be mixed with any other fluids N-8 - 49' Nylon Tube 3/8" Features: Semi-Rigid Nylon Tube at 3/8 Inch OD (49' Coil, You Cut to length to suit) Use with HP Compression Olive and Nut Fittings Supplied in HY EL O/B KIT Stainless Steel Tube & Rod for Up To 150HP Up To 150HP Outboard Specifications: Cylinder Tube = Stainless Steel Cylinder Tube Dia. = 1.33 Inches Cylinder Rod = Stainless Steel Cylinder Brackets = Stainless Steel Cylinder 1 " Nylok Nuts = Stainless Steel Cylinder End Caps = Cast Aluminum Cylinder Rod Stroke = 7-1/2 Inches Cylinder Type = Un Balanced Cylinder  Cylinder Volume Big Side Vol = 155 ccSmall side Vol = 115 cc Steering Wheel HO/HO = 5.5 and 4.1 Turns Total length Rod Compressed = 15.75 Inches Rod Extended = 23.00 Inches Cylinder Total Weight = 3.15 Pounds (1427 Grams)

WP019 Water Pump Repair Kit for Yamaha Outboard Engines This water pump repair kit is designed for specific Yamaha outboard engines. Fits Yamaha 150HP 1999 and up, 175HP 1992 - 2001, 200HP 1992 and up, 225HP 2000 and up, 300HP 2003 and up. Replaces: YAMAHA Water Pump Repair Kit 61A-W0078-A3-00 YAMAHA Water Pump Repair Kit 61A-W0078-A4-00 YAMAHA Water Pump Repair Kit 61A-W0078-A2-00 YAMAHA Water Pump Repair Kit 65L-W0078-A0-00 SIERRA Water Pump Repair Kit 18-3396-1 SIERRA Water Pump Repair Kit 18-3396 EMP Water Pump Repair Kit 46-02346 EMP Water Pump Repair Kit 46-46202 Warranty Information When properly installed, all ARCO products are warrantied against defects in materials and workmanship for 12 months for leisure use and 90 days for commercial or racing applications. Add an extra year of warranty to your rotating electric ARCO product (Tilt/Trim Motors, Alternators, Outboard Starters, and Inboard Starters) when you register your product within 30 days of purchase. You can register your product by visiting arcomarine.com/product-registration.

HOT FOOT™ Universal Original Foot Throttle for All Marine Engines Now compatible with all Mercury 175-300 Pro XS outboard motors The Original and ONLY real HOT FOOT™ Throttle Drive your boat safer by driving it like your car. This is the one and only HOT FOOT™ throttle - the original boat foot throttle that has been on the market for 30+ years. This throttle allows you to drive your boat like you do your car. You keep both hands on the wheel and control the throttle with your foot. The throttle returns to idle if you remove your foot. This throttle is a must-have for safe operation of high performance boats. Features: Drive your boat like you drive your car -- features make driving your boat fun and safe Number one throttle on the market for over 20 years Provides added safety and performance Improves throttle control for all outboard and inboards All cast aluminum and stainless steel hardware Lightweight and resistant to corrosion Stainless steel hardware and non-sticking teflon and nylon bearing surfaces for trouble free operation Nylon and teflon bushings on all critical pivot points Stainless steel spring returns engine to idle position when released Equipped with toe clip for additional safety in extreme operating conditions Uses standard control cables for easy hook-up (longer throttle cable not included) Mounts directly to floor of boat with four screws (not included) Patented Idle Stop for FICHT and Optimax Engines Optional Slide Mount (HFM-1-DP) available for comfort and multiple drivers WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Atlas Micro Jacker Small Outboard Hydraulic Jack - 4" SMALLEST & LIGHTEST HYDRAULIC JACK ON THE MARKET For Small Outboards - Max Weight 425 lbs / Max Horsepower 115 HP Great For Shallow Water Boats – Gheenoes     River Runners – Jon Boats - Skiffs Get Out of Trouble Fast – Lifts in 8 Seconds Lightweight – Only 23 Pounds Fish “Skinny Water” With Confidence Self Contained Hydraulics Maximum outboard dry weight: 425 pounds Maximum outboard horsepower: 115 HP* Only Four (4) Inch Setback Clamp-On Motor Adapter Available (optional) Small Footprint – Only 14-5/8” Wide and 11-1/2” High Clamp-On Motor Adapter (part # AHJM-CMA-DP) allows you to mount smaller engines with clamp-on brackets to the ATLAS Micro Jacker, since they do not mount with bolts on the standard BIA engine hole pattern. Adjustment Specifications: With the Micro Jacker in place, you will have about 8.5” to work with in height. This includes 1.5” of adjustment at the transom, another 1.0” on the motor side, 1.0" of adjustment with the motor, and 5" of hydraulic lift with the Micro Jacker itself. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Sierra fuel pump kits for Mercury/Mariner outboards.

ATLAS™ 10" Hydraulic Jack Plate Standard - Black Anodized The Atlas revolutionary design meets the demands of today's high performance outboards. The one piece design, featuring the innovative Rod and Slot lifting system, will handle the stresses from the heaviest and most powerful outboards, up to 300 HP or 625 pounds, on the market today.  All of the hydraulics are built into the jack eliminating the necessity of installing pumps and reservoirs inside the transom. The all new hydraulic unit is fast too..lifting from bottom to top in 8 seconds! WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

ATLAS™ 10" Hydraulic Jack Plate Heavy-Duty for Verado - Black T-H Marine’s ATLAS™ Hydraulic Jack Plate is now available in a “HEAVY DUTY” upgrade.T-H Marine’s ATLAS™ Hydraulic Jack Plate is the #1 selling jack plate in the world and the #1 Choice by fishing professionals and boat manufacturers. With the ATLAS™ HEAVY DUTY, the product is available for applications on even larger outboards, rated for engines up to 400 hp. 5 REASONS YOU SHOULD CHOOSE THE ATLAS™ HYDRAULIC JACK PLATE ATLAS™ is truly the best hydraulic jack plate in the world ATLAS™ is factory installed by more boat manufacturers than any other plate ATLAS™ is used by more professional fisherman than any other hydraulic jack plate ATLAS™ is the #1 selling hydraulic plate in the world – sold & serviced by more outlets ATLAS™ hydraulic actuator is made in the U.S.A. vs. our competitors being from China 6 WAYS THE ATLAS™ CHANGED HYDRAULIC JACK PLATES FOREVER ATLAS™ is made by T-H Marine/CMC, who were the FIRST to offer an actuator inside the jack plate – the competition copied ATLAS™ was the first plate to offer predrilling for shallow water anchors – the competition copied ATLAS™ was the first and only plate that did not require regular grease lubrication – the competition design cannot do that ATLAS™ was the first plate to include a heavy duty safety cable to protect boaters from engine entering cockpit upon failure ATLAS™ was the first plate to offer a very simple actuator replacement in the field ATLAS™ was the first major development in hydraulic jack plates in over a decade – spurring hydraulic jack plate improvement WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.