BURKS T310GA5-1 1/4, CENTRIFUGAL PUMP 3PH 1HP TEFC Close Coupled, 60 Hz, Three Phase, 3500 RPM, 1 Horsepower, TEFC Motor Enclosure, Frame Size 56J.   UNSPSC Code: 40150000

Oberdorfer 405M-4-24N18Bct Pump 1Hp 1800Rpm 24V FEATURES Pump Body: Bronze Ports: 1" NPT and 1 1/2" Hose Flow: 24 GPM at 20 feet of head Impeller: Neoprene Standard, Buna Optional Shaft Seal: Mechanical Shaft: Stainless Steel Motor / Drive: Close coupled Rubber Impeller Pumps are mounted directly onto the motor without the use of a shaft coupling. This pump is designed to be coupled to a Nema C 56C faced motor. It uses an aluminum adapter plate to accommodate the pump. The gas engine mount has its own adapter. We can supply additional motors and assemble for you.     APPLICATIONS / CHARACTERISTICS RUBBER IMPELLER PUMP BRONZE CLOSE COUPLED Close coupled Rubber Impeller Pumps are made of high quality bronze for maximum corrosion resistance. The rubber impeller is mounted on a separate stainless steel shaft which is counterbored on the outer end in order to slide over the carbon steel motor shaft. Ball or sleeve bearings in the motor or engine support the shaft. Model 405M has a mechanical seal. Impellers are made of Neoprene rubber, Buna N impellers are available on request. Suction lifts of 15 ft. are possible when pump is fully primed. Portable. Compact. Easy Impeller Replacement. Vacuum Switch Shut-off Optional.     Oberdorfer Flexible Impeller Utility Pump, 1"NPT Ports, Neoprene Impeller, 1HP 24V 1800RPM TEFC Motor  

Oberdorfer 405M-4-12N18Bct Pump 1Hp 1800Rpm 12V FEATURES Pump Body: Bronze Ports: 1" NPT and 1 1/2" Hose Flow: 24 GPM at 20 feet of head Impeller: Neoprene Standard, Buna Optional Shaft Seal: Mechanical Shaft: Stainless Steel Motor / Drive: Close coupled Rubber Impeller Pumps are mounted directly onto the motor without the use of a shaft coupling. This pump is designed to be coupled to a Nema C 56C faced motor. It uses an aluminum adapter plate to accommodate the pump. The gas engine mount has its own adapter. We can supply additional motors and assemble for you.     APPLICATIONS / CHARACTERISTICS RUBBER IMPELLER PUMP BRONZE CLOSE COUPLED Close coupled Rubber Impeller Pumps are made of high quality bronze for maximum corrosion resistance. The rubber impeller is mounted on a separate stainless steel shaft which is counterbored on the outer end in order to slide over the carbon steel motor shaft. Ball or sleeve bearings in the motor or engine support the shaft. Model 405M has a mechanical seal. Impellers are made of Neoprene rubber, Buna N impellers are available on request. Suction lifts of 15 ft. are possible when pump is fully primed. Portable. Compact. Easy Impeller Replacement. Vacuum Switch Shut-off Optional.   Oberdorfer Flexible Impeller Utility Pump, 1"NPT Ports, Neoprene Impeller, 1HP 12V 1800RPM TEFC Motor  

Scot Pump 35065 MPU AB 1-1/4 X 1 1/2 HP TEFC Pump • All Bronze marine centrifugal pump Freshwater or seawater applications • Precision machined to close tolerances for consistent performance. • Hardware - Type 303 stainless steel • Semi-open impeller handles solids • Impeller mounted on motor shaft • Heavy-duty, designed for continuous 24 hour – 7 day operation. • Stainless steel shaft.   Shaft Seal • Rated at 75 PSI – 5 BAR • Seawater Buna rubber parts, ceramic stationary and carbon rotating element, stainless steel spring and metal components   Motor - 2 Pole • Totally enclosed fan cooled IP-44 motors meet marine, European, and Coast Guard ignition protected requirements. • Sealed ball bearings • Single-phase capacitor start 60 Hz – 115/230 Volt • Dual frequency 50 Hz or 60 Hz motors are available • Three phase motors are not available 

Little Giant Submersible Pump Little Giant 1-A Submersible Pump Small submersible oil-filled pump with epoxy coated cast aluminum housing. For commercial, industrial and home applications including statuary fountains, water displays, air conditioners, machine tool coolants, and many other applications where liquid must be transferred or recirculated. This compact 170 GPH pump features a 1/4" MNPT discharge, 7' shut-off head capability, and screened inlet. This pump is not recommended for aquariums, swimming pools and fuel oil transfer.   Features: 170 GPH @ 1 ft. Horespwoer 1/200, 115 Volt, 1.1 Amps Operates submersed. 6' cord Epoxy-coated aluminum housing Bottom inlet has snap-off screen for easy cleaning. 1/4" MNPT outlet, with 90° elbow accessory, accepts 1/2" I.D. tubing

BURKS 09812F, MOTOR 3PH 3HP ODP CS

BURKS T350G6-1 1/2, CENTRIFUGAL PUMP 3PH 5HP TEFC Close Coupled, 60 Hz, Three Phase, 3500 RPM, 5 Horsepower, TEFC Motor Enclosure, Frame Size 184JM   UNSPSC Code: 40150000

BURKS 23922, Centrifugal Pump 2 hp Bronze Impeller

BURKS 21123, IRON CASE FOR WA6 PUMP

BURKS 20CS6M Close Coupled Turbine Pump BURKS exclusive unique regenerative type turbine pumps. Designed to handle clear water in addition to and many other non-abrasive, lower viscosity liquids on high pressure. As well as low capacity applications with the greatest possible efficiency.   BURKS is the only turbine pump with Life-Lok® External Impeller Adjustment. This feature allows re adjustment of impeller without disturbing piping, disassembling pump or replacing parts. This, as a result, gives up to 40% longer service life than turbine pumps of other designs.   Self-Priming Pump Compact and Space-saving size No coupling so this eliminates misalignment problems Dependable carbon/ceramic mechanical shaft seal for same temperatures to 225 °F (107° C). Bronze impeller with Monel blades, therefore the only moving part Bronze raceway with cast-in vortex pockets – will not vapor lock #303 Stainless Steel pump shaft Every pump is factory tested     Motor Information 4CS Series: Single Phase motors are 115/208-230 Volt, 60 Hz, 1750 RPM and therefore Three Phase motors are 208-230/460 Volts, 60/50 Hz, 1750/1450 RPM.     CS Series: Single Phase motors are 115/208-230 Volt, 60 Hz, 3450 RPM Three Phase 1, 11/2 & 2HP. – 208-230/460 Volt, 60/50 Hz., 3450/2900 RPM Three Phase 3 & 5 HP – 208-230/460 Volt, 60 Hz, 3450 RPM Standard pump motors have open drip proof construction and are rated with jet pump service factors for continuous duty operation at all ratings shown. Single phase motors are capacitor start/induction run with built-in overload protection. Three phase motors require a magnetic type starter which provides full 3-leg overload protection. Failure to use the correct starter and overloads will void the warranty.   High Temperature   For Temperatures to 500 °F (260 °C). Series CS Pumps are available while in a Jacketed Seal Cavity design for pumping hot oil, hot water and heat transfer fluids in common use in high temperature heating or cooling applications. This feature greatly extends seal life in high temperature applications. 

BURKS 350G6-1 1/2, Centrifugal Pump 230/460v 3PH 5HP Bronze Fitted Cast Iron Construction.  Close Coupled to a 5 Horsepower, 3450 RPM, 230/460 Volts, 3 Phase Motor.  Ports are 2 Inches NPT Inlet, 1-1/2 Inches NPT Outlet. Impeller Diameter is 5.88 Inches.   UNSPSC Code: 40150000  

BURKS T37CT7MV, TURBINE PUMP 60 VOLTS 3PH 3/4HP Bronze Fitted Cast Iron Construction. Seal and O-ring are VITON. Pump is close Coupled to a 3/4 Horsepower , 3450 RPM, 208-230/460 HZ , 60 Volt, 3 Phase, TEFC Motor. Ports are 1 Inches NPT Inlet, 1 Inches NPT Outlet.   UNSPSC Code: 40150000

Applications for the TE-7R-MD Magnetic Drive Pump include chemical recirculation, chemical transfer, bicarbonate systems, deionized water systems, refrigerators, scrubber systems, detergent mixers, computer cooling, carbon arc furnace cooling, ion exchange recovery, and aquariums.   March Pump's industrial TE-7R-MD is an American seal-less centrifugal magnetic drive pump ideal for applications such as chemical recirculation, chemical transfer, and scrubber systems. It is capable of generating a maximum flow of 53 gallons per minute at 10 feet, and its maximum head is 60 Feet (or around 26PSI). The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Viton, Ryton/Teflon/Carbon, and Ceramic. The inlet connection is 1.5 inch female pipe thread, and the outlet is 1 inch male pipe thread. The standard motor is a 1 Phase 115/230V or 3 Phase 230/460V 0.75 Horsepower totally enclosed fan cooled motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options). The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheit or 87 Celsius. The March TE-7R-MD centrifugal magnetic drive pump is capable of handling mildly or highly corrosive chemicals, acids, and solvents.     Unit System 60Hz 50Hz Max Flow 53 GPM 180 LPM Max Head 60 FT 12.3 M Power .75 HP .559 KW Electrical 1PH 115/230V or 3PH 230/460V 50/60HZ     Type Centrifugal Mag Drive Inlet 1-1/2"FPT Outlet 1"MPT Wet End Polypropylene (Front Housing, Impeller), Ryton (Rear Housing), Viton (O-Ring), Ceramic (Shaft, Thrust Washer), Ryton/Teflon/Carbon (Bushing) Motor Options Available in .75HP, 1HP, 1.5HP, 1HP Explosion Proof, or 1.5HP Explosion Proof

Applications for the TE-7S-MD Magnetic Drive Pump include chemical recirculation, chemical transfer, refrigerators, scrubber systems, detergent mixers, computer cooling, carbon arc furnace cooling, silver recovery systems, and marine air conditioners.    March Pump's industrial TE-7S-MD is an American seal-less centrifugal magnetic drive pump ideal for applications such as chemical recirculation, chemical transfer, and scrubber systems. It is capable of generating a maximum flow of 53 gallons per minute at 10 feet, and its maximum head is 57.5 Feet (or around 25PSI). The standard wet end (the materials that come into contact with the solution) is composed of 316 Stainless Steel, Viton, Carbon, and Ceramic. The inlet connection is 1.5 inch female pipe thread, and the outlet is 1 inch male pipe thread. The standard motor is a 1 Phase 115/230V or 3 Phase 230/460V 1 Horsepower totally enclosed fan cooled motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options). The maximum internal pressure the pump can tolerate is 200PSI, and the maximum liquid temperature is 250 Fahrenheit or 121 Celsius. The March TE-7S-MD centrifugal magnetic drive pump is capable of handling mildly or highly corrosive chemicals, acids, and solvents.     Unit System 60Hz 50Hz Max Flow 53 GPM 180 LPM Max Head 57.5 FT 12 M Power 1 HP .745 KW Electrical 1Ph 115/230V or 3Ph 230/460V 50/60HZ     Type Centrifugal Mag Drive Inlet 1-1/2"FPT Outlet 1"MPT Wet End 316 Stainless Steel (Front Housing, Rear Housing, Impeller), Viton (O-Ring), Ceramic (Shaft, Thrust Washers), Carbon (Bushing) Motor Options Available in 1HP, 1.5HP, 1HP Explosion Proof or 1.5HP Explosion Proof

BURKS 21942-1, MECHANICAL SEAL