BURKS 310G5-1 1/4, BURKS CIRCULATION G5 PUMP 230-440V 1HP 3PH Centrifugal Pump and Motor unit. Bronze Fitted Cast Iron Construction. Close Coupled to a 1 Horsepower, 3450 RPM, 230/460 Volts, 3 Phase Motor. Ports are 1-1/2 Inches NPT Inlet, 1-1/4 Inches NPT Outlet. Impeller Diameter is 4.25 Inches.

BURKS 22149-B, PUMP CASING UNSPSC Code: 40150000

BURKS 22403-6.25, WET END FOR 2" G6 PUMP Pump kit Only* for all G6-2 Series, 213-215JM Nema frame size only (*no motor – full sized impeller – impeller trim required). Catalog # 22403-6.25 For assembly on motor with a 213-215JM Nema frame Motor (check motor specs.). Full size impeller is 6.25 Inches Diameter. NOTE : Impeller diameter must be trimmed to suit Horsepower or previous Impeller diameter.

BURKS 23922, Centrifugal Pump 2 hp Bronze Impeller

BURKS 20CS6M Close Coupled Turbine Pump BURKS exclusive unique regenerative type turbine pumps. Designed to handle clear water in addition to and many other non-abrasive, lower viscosity liquids on high pressure. As well as low capacity applications with the greatest possible efficiency.   BURKS is the only turbine pump with Life-Lok® External Impeller Adjustment. This feature allows re adjustment of impeller without disturbing piping, disassembling pump or replacing parts. This, as a result, gives up to 40% longer service life than turbine pumps of other designs.   Self-Priming Pump Compact and Space-saving size No coupling so this eliminates misalignment problems Dependable carbon/ceramic mechanical shaft seal for same temperatures to 225 °F (107° C). Bronze impeller with Monel blades, therefore the only moving part Bronze raceway with cast-in vortex pockets – will not vapor lock #303 Stainless Steel pump shaft Every pump is factory tested     Motor Information 4CS Series: Single Phase motors are 115/208-230 Volt, 60 Hz, 1750 RPM and therefore Three Phase motors are 208-230/460 Volts, 60/50 Hz, 1750/1450 RPM.     CS Series: Single Phase motors are 115/208-230 Volt, 60 Hz, 3450 RPM Three Phase 1, 11/2 & 2HP. – 208-230/460 Volt, 60/50 Hz., 3450/2900 RPM Three Phase 3 & 5 HP – 208-230/460 Volt, 60 Hz, 3450 RPM Standard pump motors have open drip proof construction and are rated with jet pump service factors for continuous duty operation at all ratings shown. Single phase motors are capacitor start/induction run with built-in overload protection. Three phase motors require a magnetic type starter which provides full 3-leg overload protection. Failure to use the correct starter and overloads will void the warranty.   High Temperature   For Temperatures to 500 °F (260 °C). Series CS Pumps are available while in a Jacketed Seal Cavity design for pumping hot oil, hot water and heat transfer fluids in common use in high temperature heating or cooling applications. This feature greatly extends seal life in high temperature applications. 

BURKS 3CR6M, Turbine Pump 230VAC Burks 3CR6M Turbine Pump. Close Coupled 230 Volts 60 Hz, Single Phase, 3450/2850 RPM, 1/3 Horsepower. ODP Motor Enclosure.   UNSPSC Code: 40150000

BURKS ED10M, TURBINE PUMP ONLY Bronze Fitted Cast Iron Construction. Base mounted Pump Only less Motor. Ports are 2-1/2 Inches NPT Inlet, 2 Inches NPT Outlet.   UNSPSC Code: 40150000

BURKS ED14M, TURBINE PUMP ONLY All BRONZE Construction. Base mounted Pump Only less Motor. Ports are 2-1/2 Inches NPT Inlet, 2 Inches NPT Outlet.   UNSPSC Code: 40150000

Burks 22537-6.75 Pump Wet End Only   Please allow 3 to 4 weeks of lead time.

BURKS 21942-1, MECHANICAL SEAL

BURKS 8514-1, MECH SEAL .625

BURKS 9740-1, CI FRAME FOR WA6 UNSPSC Code: 40150000

BURKS 9762-1, SEAL 5/8 VITON UNSPSC Code: 40150000

BURKS 375G6-2", Centrifugal Pump 3PH 7.5HP 230/460v Centrifugal Pump and Motor unit. Bronze Fitted Cast Iron Construction. Close Coupled to a 7-1/2 Horsepower, 3450 RPM, 230/460 Volts, 3 Phase Motor. Ports are 2-1/2 Inches NPT Inlet, 2 Inches NPT Outlet.  Impeller Diameter is 6.06 Inches.   UNSPSC Code: 40150000

BURKS ET7M, TURBINE PUMP NO MOTOR Bronze Fitted Cast Iron Construction. Base mounted Pump Only less Motor. This is a pedestal Pump End only, to be Base Mounted and long coupled to a motor. Ports are 1 Inches NPT Inlet, 1 Inches NPT Outlet.   UNSPSC Code: 40150000