Shackle Bolts & Lock Nuts - 3-1/2" Use with heavy duty 9/16" eye springs and spring hanger brackets. Fluted shank prevents the bolt from turning in the bracket, preventing bracket wear. Sold in pairs.

Zinc U-Bolt 7/16"-14 X 3-1/8" X 4" with Washers & Nuts - Square Zinc-plated u-bolt for mounting brackets & accessories to trailer frames. Features: Square bend Grade 5 7/16"-14 diameter/thread 3-1/8" W x 4" L *Comes packaged with nuts and washers.

Zinc U-Bolt 7/16"-14 X 3-1/8" X 3" with Washers & Nuts - Square Zinc-plated u-bolt for mounting brackets & accessories to trailer frames. Features: Square bend Grade 5 7/16"-14 diameter/thread 3-1/8" W x 3" L *Comes packaged with nuts and washers.

Twisted Shackle - 1/2" Pin - 2-9/16"L x 3/4"W Features: High strength to weight ratio Grade 316 Stainless Steel bodies and pins Drilled shackle pin for siezing wire

Y-Stop 3" x 3" - 1/2" ID Yellow PVC Features: 1/2" ID Color: Yellow PVC Y-Stop 3" x 3"

Impeller Kit - 8 Blade - Neoprene - 2-9/16" Diameter x 3" W, 5/8" Shaft Diameter Features: Material: Neoprene Drive Type: Spline Drive Number of Blades: 8 Dimensions: Diameter: 2-9/16", Shaft Width: 3", Shaft Diameter: 5/8" Insert Material: Brass Jabsco flexible impellers can be fitted to most makes and models of bronze flexible impeller engine cooling, bilge, transfer and general purpose pumps. Jabsco flexible impellers are subjected to rigorous quality processes to ensure reliable, efficient and long lasting performance. Replace all impellers at least once every year, or sooner, depending on the engine duty. When the installation is correct an impeller may last for several years, but it is always advisable to stick to a schedule of preventative, rather than corrective, maintenance. Replacing impellers is easy. By removing the end cover screws, it is possible to remove the impeller by using either a Jabsco Impeller Removal Tool, or channel lock pliers, to grip the hub of the impeller. Don?t use screwdrivers as they may damage the face of the pump body, causing leaks, and they can be dangerous in confined spaces. Always carry spare impellers on board in case of emergency. The impeller is one of the most vital components of the engine cooling system and should always be treated as such. Always grease new impellers. Firstly, it makes it easier to install the impeller into the pump bore, and secondly it gives added protection to the impeller during initial prime. After replacing the gasket and end cover the pump is ready to use. WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Impeller Kit - 9 Blade - Nitrile - 3-3/4" Diameter x 3-1/2" W, 1" Shaft Diameter Features: Material: Nitrile Drive Type: Spline Drive Number of Blades: 9 Dimensions: Diameter: 3-3/4", Shaft Diameter: 1", Shaft Width: 3-1/2" Jabsco flexible impellers can be fitted to most makes and models of bronze flexible impeller engine cooling, bilge, transfer and general purpose pumps. Jabsco flexible impellers are subjected to rigorous quality processes to ensure reliable, efficient and long lasting performance. Replace all impellers at least once every year, or sooner, depending on the engine duty. When the installation is correct an impeller may last for several years, but it is always advisable to stick to a schedule of preventative, rather than corrective, maintenance. Replacing impellers is easy. By removing the end cover screws, it is possible to remove the impeller by using either a Jabsco Impeller Removal Tool, or channel lock pliers, to grip the hub of the impeller. Don?t use screwdrivers as they may damage the face of the pump body, causing leaks, and they can be dangerous in confined spaces. Always carry spare impellers on board in case of emergency. The impeller is one of the most vital components of the engine cooling system and should always be treated as such. Always grease new impellers. Firstly, it makes it easier to install the impeller into the pump bore, and secondly it gives added protection to the impeller during initial prime. After replacing the gasket and end cover the pump is ready to use. WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Stake Pocket The easiest and most secure way to add removeable sides to a trailer. Sized to receive standard 2" x 4" studs. Features: Bolts onto trailer 11 gauge Hot dipped galvanized 3/8" holes for bolting to frame Center hole for an optional locking bolt Dimensions: 2-1/2" x 1-1/2" x 3-1/2"

Adjustable Mid Mount Rod Holder - 1-1/4" or 1-5/16" OD - White Powder Coat Aluminum with Sleeve & Hex Key C.E. Smith's line of white powder coated clamp-on rod holders offer a great alternative to stainless steel. These rod holders are constructed of marine grade aluminum that has been 100% anodized for functionality and style. Features: Style: Adjustable Mid Mount Fits rails with 1-1/4" or 1-5/16" measured OD Made from Marine Grade Aluminum WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Double Slot Swivel Bolster Bracket Assembly - 13" C.E. Smith's adjustable bracket is designed to support roller bunks. Hot dip galvanizing for years of use in the harsh marine environment. This bracket assembly uses bolster bracket-10102G and swivel bracket-10200G. Features: Bolster bracket: 12" bracket, 11 gauge material, 2-1/2" wide, slots 1/2" wide, swivel hole 1/2" dia., slots 4-3/4" Swivel bracket: 11 gauge material, bunk flange 1-3/8" x 3-1/2", bunk flange holes 3/8" dia., swivel flange 2" tall x 3-1/2", swivel flange hole 1/2" dia., hole centers 2-1/2" Overall assembly length is 13"

Vertical Bunk Bracket Dimpled - 7-1/2" Adjustable bunk bracket. Used when mounting bunks on edge. Ideal for small craft trailers. A single bracket will allow the bunk board to pivot with the hull as the boat is loaded. Double brackets hold the board in place. Features: 7-1/2" Slot 7/16" x 4-3/8" 11 gauge materical, galvanized finish Dimpled style

Adjustable Mid Mount Rod Holder - 1.66" or 1-1/2" OD - White Powder Coat Aluminum with Sleeve & Hex Key C.E. Smith's line of white powder coated clamp-on rod holders offer a great alternative to stainless steel. These rod holders are constructed of marine grade aluminum that has been 100% anodized for functionality and style. Features: Style: Adjustable Mid Mount Fits rails with 1.66" or 1-1/2" measured OD Made from Marine Grade Aluminum WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Swivel Bracket Kit Galvanized swivel top brackets provide vertical and tilting adjustments for trailer bunks. Swivel Brackets for mounting Bunk Boards to Bolster Brackets. Features: Bunk flange holes 3/8" dia. Bunk flange 1-3/8" x 3-1/2" Swivel flange hole 1/2" dia. Swivel flange 2" tall x 3-1/2" 2-1/2" bunk flange hole centers & 1 hole centered 10 gauge material *Sold as kit with (2) brackets, (2) 7/16" x 1" head cap screws, and (2) 7/16" nylon lock nuts.

Swivel Bracket Assembly - 8" Bracket This Smith adjustable bracket is designed to support bunk boards. Hot dip galvanizing for years of use in the harsh marine environment. This bracket assembly uses bolster bracket-10100G and swivel bracket-10200G. Features: Bolster bracket: 8" bracket, 11 gauge material, 2-1/2" wide, slots 1/2" wide, swivel hole 1/2" dia., slots 2-3/4" Swivel bracket: 11 gauge material, bunk flange 1-3/8" x 3-1/2", bunk flange holes 3/8" dia., swivel flange 2" tall x 3-1/2", swivel flange hole 1/2" dia., hole centers 2-1/2" Overall assembly length is 9"

Center Swivel Bracket - 2-1/2" Galvanized swivel top bracket provides vertical and tilting adjustment for trailer bunks. Swivel Bracket for mounting Bunk Boards to Bolster Brackets. Features: Bolt-on installation Bunk flange holes 3/8" dia. Bunk flange 1-3/8" x 3-1/2" Swivel flange hole 1/2" dia. Swivel flange 2" tall x 3-1/2" 2-1/2" bunk flange hole centers 11 gauge galvanized steel Made in the USA Sold individually