Wiring Harness, 60 amp (712A, 912, 915, T2400, T4000, T3200PO, AP3500)

Circuit Breaker, 60 amp (712A, 912, 915, T2400, T4000, T3200PO, ST712, SH12HBM, AP3500)

Plug (712A, 912, 915, T2400, T4000, T3200PO, ST712, BH12, SH12HBM, AP3500)

Socket (712A, 912, 915, T2400, T4000, T3200PO, ST712, BH12, SH12HBM, AP3500)

Switch (712A, 912, 915, T2400, T4000, T3200PO, ST712)

40' x 7/32" Replacement Galvanized Cable with Hook For all manual and electric trailer winches. High chromium content and added nickel make these cables virtually impervious to corrosion and add years of service. Ideal for any winch using 7/32 inches diameter cable, designed for handling boats up to 11,500 pounds, superior 7 x 19 strand cable construction for maximum pulling strength. Complete installation instructions included. Available with heavy duty zinc plated pulley block. Features: Galvanized cable with hook 40 feet x 7/32 inches Replacement for RC30, RC23, 712A, 912, 915 T2400 and AP3500 winches

Thrust Bearing, Thrust Washers, and Springs (712A, 912, T2400, T4000, ST712, VS190, AP3500)

Male Plug & Socket for 712, 912, 915, RC30 & RC23 Replacement wiring harness plug to fit the socket. For Powerwinch Models: 712, 912, 915, RC30, and RC23.

ATP Wiring Harness & Switch Kit - 1 Lamp Universal Features: 9 ft lead for light bar connector(s) Universal wiring harness and switch kit (for 1 lamp, ATP connector) Universal plug-n-play wiring harness with on/off rocker switch 12V DC relay 30A fuse Use with 1 Heise light 160 watts or more

Wire Harness - High Power f/40" - 50" Light Bar This 13' wiring harness is designed to connect a single 40"-50" LED light bar to your 12V electrical system. It features battery terminals on one end and a Deutsch connector on the other to connect to the light. It incorporates an inline fuse holder, a 12V relay, and a waterproof switch. This harness is compatible with the following RIGID Industries LED Lights: 50" E-Series, 50" SR-Series. Features: 14 AWG Wire Deutsch Connector Inline Fuse Holder

Wire Harness f/10"-30" Light Bar This 11' wiring harness is designed to connect a single 10"-30" LED light bar to your 12V electrical system. It features battery terminals on one end and a Deutsch connector on the other to connect to the light. It incorporates an inline fuse holder, a 12V relay, and a waterproof switch. This harness is compatible with the following RIGID Industries LED Lights: 10" E-Series, 10" SR-Series, 20" E-Series, 20" SR-Series, 30" E-Series, 30" SR-Series, 40" E-Series, 40" SR-Series. Features: 16 AWG Wire Deutsch Connector Inline Fuse Holder 12 Volt Relay

Wire Harness f/4"-6" Light Bar This 11' wiring harness is designed to connect a single LED light to your 12V electrical system. It features battery terminals on one end and a Deutsch connector on the other to connect to the light. It incorporates an inline fuse holder, and a waterproof switch. This harness is compatible with the following RIGID Industries LED Lights: Dually (Single), D2 (Single), 4" E-Series, 6" E-Series, 4" SR-Series, 6" SR-Series. Features: 18 AWG Wire Deutsch Connector Inline Fuse Holder

Wire Harness f/Dually Pair This 14' wiring harness is designed to connect a pair of Dually LED lights to your 12V electrical system. It features battery terminals on one end and Deutsch connectors on the other to connect to the lights. It incorporates an inline fuse holder, and a waterproof switch. This harness is compatible with the following RIGID Industries LED Lights: Dually (Pair). Features: 18 AWG Wire Deutsch Connector Inline Fuse Holder

2-Lamp Wiring Harness & Switch Kit From the leader in the lighting industry.  This universal wire harness is for DT connected lights and wire harnesses and allows a full-length installation.  Fully loaded and ready to be installed with two (2) Heise light bars (22" or smaller) and Heise cube lights. Specifications: 9' in Length Black in color In the Box: 12v DC Relay 30 amp Fuse Two (2) - two (2) Pin DT Connectors for two (2) Lamps Waterproof Fuse Holder On/Off Rocker Switch *Sold as an Individual 

Adapt XE Wire Harness The custom 70"(1.77M) wiring harness is specifically designed to connect RIGIDs Adapt XE  Extreme Enduro LED Moto Kit and switch to your bike's electrical system. It features battery terminals on one end and bullet connectors on the other to connect the light to the custom 3 position switch.  Also included is a blue wire with an insulated butt connector to power the light and switch and an in-line 15A fuse holder. Features: Length - 70 " (1.77 M) wiring harness Features battery terminals on one end and bullet connectors on the other Connect the light to the custom 3 position switch Inline 15A fuse holder included *Sold as an Individual