Carpeted bunkboards provide proper center loading even in wind or side current conditions. 2'' x 4'' X 24" boards tilt to hug the hull and are covered with high grade marine carpet. Height of 21'' with adjustment out to 13" from frame on each side. Can be mounted on top of frame for extra height. Complete with mounting hardware to fit frames up to 3'' wide x 4-1/4'' high. WARNING: This product can expose you to chemicals including ARSENIC ,CADMIUM which are known to the State of California to cause cancer or other reproductive harm, and BERYLLIUM,COBALT METAL POWDER,NICKEL (METALLIC) which are known to the State of California to cause cancer, and Chromium (hexavalent compounds),LEAD which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Black 40" Post Guide-On & FREE Camo Wet Lands Guide-On Pads This kit includes two C.E. Smith 40" Black Post Guide-Ons and two Camo Wet Lands Post Guide-On Pads. C.E. Smith Trailer Post Guide-Ons give a clear visual marker to know you're backing, loading, or unloading your boat trailer evenly and properly to avoid costly damage. Unlike plastic guide-ons that fall apart or break with minimal impact, C.E. Smith Post Guide-Ons boats square 16 gauge steel uprights, pre-galvanized for corrosion resistance, and 2-3/8"-dia. Black PVC posts, to stand up strong season after season.  While the camo post-guide-on pads, are used to protect the boat finish from scuffs. They are sized for a close fit on standard 2" schedule 40 PVC posts (2-3/8" actual outer diameter). Features: Provide a clear marker for backing, loading, or unloading your boat trailer 16 gauge square steel uprights Pre-galvanized construction for corrosion resistance 2-3/8" black PVC posts Built to last season after season 40" tall The cover-pads are made from strong polyurethane-coated 600D nylon fabric Covers have nylon closures on each end  Open the bottom and top of the cover-pads to allow LED guide on lamps Covers contain a 1/2" thick closed-cell polyurethane foam inner pad Color of post-guide-on covers: Camo Wet Lands Kit Includes:  Part 27626: C.E. Smith Black 40" Post Guide-Ons Part 27902: C.E. Smith Post Guide-On Pad - 36" - Camo Wet Lands  Note: Check with your state Department of Transportation for restrictions regarding maximum trailer width *Sold in pairs

Black 40" Post Guide-On C.E. Smith Trailer Post Guide-Ons give a clear visual marker to know you're backing, loading, or unloading your boat trailer evenly and properly to avoid costly damage. Unlike plastic guide-ons that fall apart or break with minimal impact, C.E. Smith Post Guide-Ons boats square 16 gauge steel uprights, pre-galvanized for corrosion resistance, and 2-3/8"-dia. Black PVC posts, to stand up strong season after season. Features: Provide a clear marker for backing, loading, or unloading your boat trailer 16 gauge square steel uprights Pre-galvanized construction for corrosion resistance 2-3/8" black PVC posts Built to last season after season 40" tall Note: Check with your state Department of Transportation for restrictions regarding maximum trailer width *Sold in pairs WARNING: This product can expose you to chemicals including ARSENIC ,CADMIUM which are known to the State of California to cause cancer or other reproductive harm, and BERYLLIUM,COBALT METAL POWDER,NICKEL (METALLIC) which are known to the State of California to cause cancer, and Chromium (hexavalent compounds),LEAD which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

PVC 40" Post Guide-On with Unlighted Posts & FREE Camo Wet Lands Post Guide-On Pads This kit includes two PVC 40" Post Guide-Ons With Unlighted Posts and two Camo Wet Lands Post Guide-On Pads. The PVC posts allow you to see the location of your trailer when it's underwater. The 2" PVC tubes make it easy to see your trailer's position when backing down the ramp. The camo post-guide-on pads are used to protect the boat finish from scuffs. They are sized for a close fit on standard 2" schedule 40 PVC posts (2-3/8" actual outer diameter). Features: Mounting hardware included Adjusts out to 13" on each Side Fits Frames up to 3" W x 4-1/4" H 18" high 2" schedule 40 white PVC posts (2-3/8" actual OD) Stands 40" above the trailer frame with white post caps Fits trailer frames up to 3" wide x 5-1/4" tall Pre-galvanized steel parts are stamped from a sheet of steel after it has already been galvanized The galvanized coating is very thin (0.45 oz. on each side) The cover-pads are made from strong polyurethane-coated 600D nylon fabric Covers have nylon closures on each end Open the bottom and top of the cover-pads to allow LED guide on lamps Covers contain a 1/2" thick closed-cell polyurethane foam inner pad Color of post guide-on covers: Camo Wet Lands Kit Includes: Part 27620: C.E. Smith 40" Post Guide-On With Unlighted Posts Part 27902: C.E. Smith Post Guide-On Pad - 36" - Camo Wet Lands Note: Check with your state Department of Transportation for restrictions regarding maximum trailer width *Sold in pairs

4' Roller Bunk Roller bunks make loading and unloading small craft at very short or even dry rams easy. Great for ramps where it is not practical to float the boat onto the trailer. Pre-assembled and pre-drilled for easy installation. Maybe be installed using mounting brackets if lift and/or angle is needed, or may be bolted directly to trailer frame for a flat bottom boat, or even mounted on top of existing bunk boards. Features: Durable 2" polypropylene rollers on 1/2" shafts mounted in a heavy gauge pre-galvanized channel Supports up to 1500lbs of well distributed weight Mounting hardware not included Sold in pairs WARNING: This product can expose you to chemicals including ARSENIC ,CADMIUM which are known to the State of California to cause cancer or other reproductive harm, and BERYLLIUM,COBALT METAL POWDER,NICKEL (METALLIC) which are known to the State of California to cause cancer, and Chromium (hexavalent compounds),LEAD which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

5' Roller Bunk Roller bunks make loading and unloading small craft at very short or even dry ramps easy. Great for ramps where it is not practical to float the boat onto the trailer. Pre-assembled and pre-drilled for easy installation. May be installed using mounting brackets if lift and/or angle is needed, or may be bolted directly to trailer frame for a flat bottom boat, or even mounted on top of existing bunk boards. Features: Durable 2" polypropylene rollers on 1/2" shafts mounted in a heavy gauge pre-galvanized channel Supports up to 1500lbs of well distributed weight Mounting hardware not included Sold in pairs WARNING: This product can expose you to chemicals including ARSENIC ,CADMIUM which are known to the State of California to cause cancer or other reproductive harm, and BERYLLIUM,COBALT METAL POWDER,NICKEL (METALLIC) which are known to the State of California to cause cancer, and Chromium (hexavalent compounds),LEAD which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

60" Black PVC Post Guide-On & FREE Camo Wet Lands Post Guide-On Pads This kit includes two 60" Black PVC Post Guide-Ons and two Camo Wet Lands Post Guide-On Pads. The C.E. Smith Trailer Post Guide-Ons give a clear visual marker to know you're backing, loading, or unloading your boat trailer evenly and properly to avoid costly damage. Unlike plastic guide-ons that fall apart or break with minimal impact, C.E. Smith Post Guide-Ons boats square 16 gauge steel uprights, pre-galvanized for corrosion resistance, and 2-3/8"-dia. Black PVC posts, to stand up strong season after season. The camo post-guide-on pads are used to protect the boat finish from scuffs. They are sized for a close fit on standard 2" schedule 40 PVC posts (2-3/8" actual outer diameter).  Features: Provide a clear marker for backing, loading, or unloading your boat trailer 16 gauge square steel uprights Pre-galvanized construction for corrosion resistance 2-3/8" black PVC posts 60" Overall Height Mounting brackets and metal uprights allow for 19” of adjustment on each side of the trailer frame. Pre-galvanized steel parts are stamped from a sheet of steel after it has already been galvanized The galvanized coating is very thin (0.45 oz. on each side) The cover-pads are made from strong polyurethane-coated 600D nylon fabric Covers have nylon closures on each end Open the bottom and top of the cover-pads to allow LED guide on lamps Covers contain a 1/2" thick closed-cell polyurethane foam inner pad Color of post guide-on covers: Camo Wet Lands Kit Includes: Part 27646: C.E. Smith 60" Black PVC Post Guide-On  Part 27903: C.E. Smith Post Guide-On Pad - 48" - Camo Wet Lands Note: Check with your state Department of Transportation for restrictions regarding maximum trailer width *Sold in pairs

C.E. Smith Company C. E. Smith Company, Inc. was established as a manufacturing firm producing precision metal stampings, fabrications and assemblies for a broad variety of industries. Stainless steel boating and fishing products are sold under the SMITH TM trademark. The line includes an adjustable, completely stainless steel t-top, fiberglass electronic boxes, t-top storage bags navigation lights and antenna bracket.

40" Post Guide-On with L.E.D. Posts & FREE Camo Wet Lands Post Guide-On Pads The kit includes two 40" Post Guide-Ons With L.E.D. Posts and two Camo Wet Lands Post Guide-On Pads. The Post Guide-Ons allows you to see the location of your trailer when it's underwater. Equipped with long-lasting, waterproof, and shockproof, one-piece red and amber LED lamps. The LED lamps make it easy to see your trailer's position when backing down the ramp and dramatically increase your trailer's visibility over the road at night. Amber light faces front, red faces rear. The camo post-guide-on pads are used to protect the boat finish from scuffs. They are sized for a close fit on standard 2" schedule 40 PVC posts (2-3/8" actual outer diameter).  Features: Mounting hardware and wiring included  40" Total Height Adjusts Out to 13" on each Side Fits Frames up to 3"W x 4-1/4"H 1-1/2" sq. 16 ga Pre-Galvanized Steel post Extends 18" Into 2" PVC tube for strength Pre-galvanized steel parts are stamped from a sheet of steel after it has already been galvanized  The galvanized coating is very thin (0.45 oz. on each side) The cover-pads are made from strong polyurethane-coated 600D nylon fabric Covers have nylon closures on each end Open the bottom and top of the cover-pads to allow LED guide on lamps Covers contain a 1/2" thick closed-cell polyurethane foam inner pad Color of post guide-on covers: Camo Wet Lands Kit Includes: Part 27740: C.E. Smith 40" Post Guide-On With LED Lighted Posts   Part 27902: C.E. Smith Post Guide-On Pad - 36" - Camo Wet Lands  Note: Check with your state Department of Transportation for restrictions regarding maximum trailer width *Sold in pairs

60" Post Guide-On with L.E.D. Posts & FREE Camo Wet Lands Post Guide-On Pads The kit includes two 60" Post Guide-Ons With L.E.D. Posts and two Camo Wet Lands Post Guide-On Pads. The Post Guide-Ons allows you to see the location of your trailer when it's underwater. Equipped with long-lasting, waterproof, and shockproof, one-piece red and amber LED lamps. The LED lamps make it easy to see your trailer's position when backing down the ramp and dramatically increase your trailer's visibility over the road at night. Amber light faces front, red faces rear. The camo post-guide-on pads are used to protect the boat finish from scuffs. They are sized for a close fit on standard 2" schedule 40 PVC posts (2-3/8" actual outer diameter).  Features:  Mounting hardware and wiring included  Adjusts Out to 19" on each Side Fits Frames up to 3"W x 4-1/4"H 1-1/2" square, 16 gauge pre-galvanized steel uprights that are 39" high 2-3/8" diameter white PVC posts Stands 60" above the trailer frame Pre-galvanized steel parts are stamped from a sheet of steel after it has already been galvanized The galvanized coating is very thin (0.45 oz. on each side) The cover-pads are made from strong polyurethane-coated 600D nylon fabric Covers have nylon closures on each end Open the bottom and top of the cover-pads to allow LED guide on lamps Covers contain a 1/2" thick closed-cell polyurethane foam inner pad Color of post guide-on covers: Camo Wet Lands Kit Includes: Part 27760: C.E. Smith 60" Post Guide-On With L.E.D. Posts Part 27903: C.E. Smith Post Guide-On Pad - 48" - Camo Wet Lands  Note: Check with your state Department of Transportation for restrictions regarding maximum trailer width *Sold in pairs

60" Black PVC Post Guide-On C.E. Smith® Trailer Post Guide-Ons give a clear visual marker to know you're backing, loading, or unloading your boat trailer evenly and properly to avoid costly damage. Unlike plastic guide-ons that fall apart or break with minimal impact, C.E. Smith Post Guide-Ons boats square 16 gauge steel uprights, pre-galvanized for corrosion resistance, and 2-3/8"-dia. Black PVC posts, to stand up strong season after season. Features: Provide a clear marker for backing, loading, or unloading your boat trailer 16 gauge square steel uprights Pre-galvanized construction for corrosion resistance 2-3/8" black PVC posts 60" Overall Height Mounting brackets and metal uprights allow for 19”  of adjustment on each side of the trailer frame. Pre-galvanized steel parts are stamped from a sheet of steel after it has already been galvanized  The galvanized coating is very thin (0.45 oz. on each side). Note: Check with your state Department of Transportation for restrictions regarding maximum trailer width. *Sold in pairs WARNING: This product can expose you to chemicals including ARSENIC ,CADMIUM which are known to the State of California to cause cancer or other reproductive harm, and BERYLLIUM,COBALT METAL POWDER,NICKEL (METALLIC) which are known to the State of California to cause cancer, and Chromium (hexavalent compounds),LEAD which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

60" Post Guide-On with I-Beam Mounting Kit & FREE Camo Wet Lands Post Guide-On Pads The kit includes two 60" Post Guide-Ons With I-Beam Mounting Kits and two Camo Wet Lands Post Guide-On Pads. These Post Guide-Ons allow you to see the location of your trailer when it's underwater. Designed for I-beam trailers and I-beam boat lifts, these guide-ons feature an innovative two-piece mounting clamp that works above or below the I-beam. Brackets will fit onto any height and virtually any width I-beam trailer frame. The camo post-guide-on pads are used to protect the boat finish from scuffs. They are sized for a close fit on standard 2" schedule 40 PVC posts (2-3/8" actual outer diameter).  Features: Mounting hardware included Adjusts out to 19" on each side 1-1/2" square. 16 gauge pre-galvanized steel uprights 2-3/8" diameter white PVC posts Pre-galvanized steel parts are stamped from a sheet of steel after it has already been galvanized  The galvanized coating is very thin (0.45 oz. on each side) The cover-pads are made from strong polyurethane-coated 600D nylon fabric Covers have nylon closures on each end Open the bottom and top of the cover-pads to allow LED guide on lamps Covers contain a 1/2" thick closed-cell polyurethane foam inner pad Color of post-guide-on covers: Camo Wet Lands Kit Includes: Part 27648: C.E. Smith 60" Post Guide-On With I-Beam Mounting Kit  Part 27903: C.E. Smith Post Guide-On Pad - 48" - Camo Wet Lands  Note: Check with your state Department of Transportation for restrictions regarding maximum trailer width *Sold in pairs

60" Post Guide-On with Unlighted Posts & FREE Camo Wet Lands Post Guide-On Pads This kit includes two 60" Post Guide-On With Unlighted Posts and two Camo Wet Lands Post Guide-On Pads. These Post Guide-Ons allow you to see the location of your trailer when it's underwater. The 2" PVC tubes make it easy to see your trailer's position when backing down the ramp. The camo post-guide-on pads are used to protect the boat finish from scuffs. They are sized for a close fit on standard 2" schedule 40 PVC posts (2-3/8" actual outer diameter).  Features: Mounting hardware included Adjusts out to 19" on each side Fits frames up to 3" W x 4-1/4" H 1-1/2" square, 16 gauge pre-galvanized steel uprights 39" high 2-3/8" diameter white PVC posts. Stands 60" above the trailer frame with white post caps. Pre-galvanized steel parts are stamped from a sheet of steel after it has already been galvanized The galvanized coating is very thin (0.45 oz. on each side) The cover-pads are made from strong polyurethane-coated 600D nylon fabric Covers have nylon closures on each end Open the bottom and top of the cover-pads to allow LED guide on lamps Covers contain a 1/2" thick closed-cell polyurethane foam inner pad Color of post guide-on covers: Camo Wet Lands Kit Includes: Part 27640: C.E. Smith 60" Post Guide-On With Unlighted Posts  Part 27903: C.E. Smith Post Guide-On Pad - 48" - Camo Wet Lands  *Sold in pairs

Double Slot Swivel Bolster Bracket Assembly - 13" C.E. Smith's adjustable bracket is designed to support roller bunks. Hot dip galvanizing for years of use in the harsh marine environment. This bracket assembly uses bolster bracket-10102G and swivel bracket-10200G. Features: Bolster bracket: 12" bracket, 11 gauge material, 2-1/2" wide, slots 1/2" wide, swivel hole 1/2" dia., slots 4-3/4" Swivel bracket: 11 gauge material, bunk flange 1-3/8" x 3-1/2", bunk flange holes 3/8" dia., swivel flange 2" tall x 3-1/2", swivel flange hole 1/2" dia., hole centers 2-1/2" Overall assembly length is 13"

60" Post Guide-On With L.E.D. Posts These Post Guide-Ons allow you to see the location of your trailer when it's under water. Equipped with long lasting, waterproof and shockproof, one piece red and amber LED lamps. The LED lamps make it easy to see your trailer's position when backing down the ramp and dramatically increase your trailer's visibility over the road at night. Amber light faces front, red faces rear.  Features: Mounting hardware and wiring included  Adjusts Out to 19" each Side Fits Frames up to 3"W x 4-1/4"H 1-1/2" square, 16 gauge pre-galvanized steel uprights that are 39" high 2-3/8" diameter white PVC posts Stands 60" above the trailer frame Made in the USA Pre-galvanized steel parts are stamped from a sheet of steel after it has already been galvanized The galvanized coating is very thin (0.45 oz. on each side) *Sold in pairs