Standard Splicing Kit Kit Includes: Ronstan splicing bag Splicing kit, 5 fid set (4, 5.5, 7.5, 10, 13mm) Scissors, 8", cuts Kevlar and Dyneema material F15 puller small, 2-4 mm line F20 puller medium, 4-6 mm line Splicing tape 5 piece needle set Leather palm, right hand, medium Whipping twine

Pro Splicing Kit Kit Includes: Ronstan splicing bag Splicing kit, 5 fid set (4, 5.5, 7.5, 10, 13 mm) Scissors, 8" cuts Kevlar and Dyneema material F15 puller small, 2-4 mm line F25 puller, 6-8 mm line Splicing tape 5 piece needle set Small Swedish fid Leather palm right hand, medium Whipping twine Dyneema whipping twine

Dinghy Specialist Splicing Kit Kit Includes: Ronstan splicing bag Ceramic knife, 4" blade Scissors, 1.75" cuts Kevlar and Dyneema material F15 puller small, 2-4mm line Splicing tape 5 piece needle set Whipping twine Small Swedish fid

Splicing Kit These five Selma Fids are all you need to splice different sizes and types of rope or line. Features: Highly polished stainless steel Fid sizes: 4, 5.5, 7.5, 10, and 13 mm Splice double and hollow braided lines from 1/8" to 9/16" Splice three-strand line or twine up to 1-1/8" WARNING: This product can expose you to chemicals including Diisononyl Phthalate (DINP) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.

14" x 12" Standard Performance Trim Tab Kit w/o Switch Kit- 12V Upgraded electro-polished trim blades with stouter 1/4" diameter hinge pin make these Performance Trim Tab Kits a cut above the base level Lenco Standard Mount Kits. Equipped with the same fast response electric actuators for precise control. Fully submersible with all Plug & Play Deutsch connections. Blades are Electro-Polished 12 gauge - 304 SS with 1" turned up edges (the 16" x 12" and the 18" x 14" have an 85 degree inside taper) and 1/4" diameter hinge pin. Kit includes Standard Actuators with 5/16" SS bolts. The actuators mount at the trailing edge of the blades Kit Contents: 2 each of 12-gauge stainless steel Electro-Polished trim tab blades 2 each of #15054-001 actuators with 6' lead and Deutsch plugs 2 each of #30133-103 20' actuator extension wiring harnesses 2 each of #15085-001 (#116) upper mounting bracket with gland seal    2 each of #50014-001 (#119) lower mounting bracket  1 each of the Lenco owner’s / installation manual All necessary stainless steel mounting hardware Specifications: Suggested Boat Length: 19' to 34' Length of Tab: 14" Width of Tab: 12" Minimum Transom Height: 11" Blades: 12 Gauge Stainless Steel Finish: Electro-Polished Switch Kit: Sold Separately Class: Fuel Efficient Compliance: CE Certified Compatibility: Any Boat Actuators: 12-volt WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

3/8" Hose Mender In-Line Fuel Splice Kit with Stainless Steel Clamps Whether it’s an emergency situation on the water or routine maintenance at the dock, this in-line fuel splice kit provides everything you need to repair 3/8-inch lines. Machined brass fitting paired with 2 stainless steel hose clamps.  Features: Everything you need to mend a 3/8-inch fuel line including 2 stainless steel hose clamps Solid machined brass with barbed ends A centered divider ensures you get the mender evenly and securely placed between both ends of the hose Very Versatile: Use with leaded, unleaded, ethanol-blended, and alcohol-blended fuels

Crown Head™ Standard Repair Kit The Deep Draft Crown Head was last made in 1990 but some still exist out in the field today. While many of the parts are similar to today’s Crown Head there are some that are no longer available. For this reason we now include the macerator retro-fit for the old Deep Draft units to make the Centrifugal Discharge series. This repair kit will update the older style Deep Draft toilets to the new CD series. For those not wishing to tear apart units Raritan still offers a Crown Head Exchange program that allows users to swap their old base for a new one at a reduced cost over buying new. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Standard Rigging Kit Everything you need to rig your TACO Marine Grand Slam 170 Outrigger poles is in this Standard Rigging Kit. Using this kit gets you on the water fast and saves you time and money. Features: Rigs up to 22' outriggers Glass ring with brass strap clips 1/8" thick, 100' Dacron black rigging cord Adjustable tension release clips 1-1/4" outrigger line stops Pad eye with screws Double sleeve crimp Swivel Snap swivel Quick-dry mesh bag 1-year limited warranty

F15 Splicing Needle w/Puller - Small 2mm-4mm(1/16"-5/32") Line A range of specialised rope splicing needles for sailors and riggers. They are specifically designed for use with modern synthetic fibres and rope constructions, in particular small line sizes where conventional fids/needles don't work. Features: "Pull-through" operation Unique double needle clamps the line making it easy to pull through Ideal for making "soft shackles" Ideal for pulling cover plaits into the core for making tapered sheets Sizes available for lines from 2mm (1/16") diam. to 8mm (5/16") diameter Fixed handle with wire running around full length for maximum strength

F20 Splicing Needle w/Puller - Medium 4mm-6mm(5/32"-1/4") Line A range of specialised rope splicing needles for sailors and riggers. They are specifically designed for use with modern synthetic fibres and rope constructions, in particular small line sizes where conventional fids/needles don't work. Features: "Pull-through" operation Unique double needle clamps the line making it easy to pull through Ideal for making "soft shackles" Ideal for pulling cover plaits into the core for making tapered sheets Sizes available for lines from 2mm (1/16") diam. to 8mm (5/16") diameter Fixed handle with wire running around full length for maximum strength

F25 Splicing Needle w/Puller - Large 6mm-8mm(1/4"-5/16") Line A range of specialised rope splicing needles for sailors and riggers. They are specifically designed for use with modern synthetic fibres and rope constructions, in particular small line sizes where conventional fids/needles don't work. Features: "Pull-through" operation Unique double needle clamps the line making it easy to pull through Ideal for making "soft shackles" Ideal for pulling cover plaits into the core for making tapered sheets Sizes available for lines from 2mm (1/16") diam. to 8mm (5/16") diameter Fixed handle with wire running around full length for maximum strength

D-SPLICER Kit w/4 Needles & 2mm-4mm(1/16"-5/32") Line D-SPLICER is a range of specialised rope splicing needles for sailors and riggers. They are specifically designed for use with modern synthetic fibres and rope constructions, in particular small line sizes where conventional fids/needles don't work. Features: "Pull-through" operation Unique double needle clamps the line making it easy to pull through Ideal for making "soft shackles" Ideal for pulling cover plaits into the core for making tapered sheets Sizes available for lines from 2mm (1/16") diam. to 8mm (5/16") diameter Kit Includes: Machined alloy handle, with anchoring loop 4 interchangeable needles (2 sizes) Storage tube WARNING: This product can expose you to chemicals including Diisononyl Phthalate (DINP) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.

Winch Service Kit -  8 Pawls & 16 Springs Pawls should be inspected, and springs should be replaced every second year. It is important to use only genuine Ronstan or Andersen brand pawls and springs in your winch. Kit Contains: 8 pawls and 16 springs Required for service: Winch handle ANDERSEN winch grease and small brush for application

Standard Dee Shackle - 15.9mm(5/8") Pin Features 20.7mm(13/16") A/F hexagonal pin head Features: High strength to weight ratio Grade 316 stainless steel bodies and pins

Standard Dee Shackle - 3.2mm(1/8") Pin Features: High strength to weight ratio Grade 316 stainless steel bodies and pins