RAM Double Swing Arm with 8" Male and No Female Tele-Pole Material: Powder Coated Steel Color: Black Powder Coat

RAM® Vertical Drill-Down Vehicle Base with Lower RAM® Tele-Pole™ Vehicle base for: Commercial vehicles with tube frame seats. May also be used as a drill down base for most any flat surface. Features: Installs in minutes with no drilling required for many uses Base can be attached to flat surfaces or tubing to create multiple mounting possibilities

RAM Yoke Clamp Mount w/Double Socket Arm & Diamond Base Adapter Part #: RAM-B-121-238U Consists of a double socket arm, universal diamond base and yoke clamp base. The hole pattern found on the diamond base will connect to many RAM cradles, as well as third party cradles including mounts with the industry standard AMPS hole pattern. The clamp base will accommodate rails in diameter from 0.625" to 1.25". The 1" rubber ball is at a right angle to the plane of the mount so when connected to a rail, the ball sits parallel to the rail. Material: Powder Coated Marine Grade Aluminum Ball Size: 1" Rubber Ball "B" Size Note: The "U" in the part number reflects product packaged in poly bag.

RAM 1.5" Diameter Ball Mount with 2/2.5" Round Bases - AMPs Hole Pattern The RAM-101U consists of a double socket arm and two 2.5" diameter round bases that contain the universal AMPS hole pattern. The mount is designed with a 1.5" diameter patented rubber ball and socket system that has adjustment points at both ends of the double socket arm; this allowing for almost infinite adjustment and perfect viewing angles. The hole pattern found on the round base adapter will connect to many RAM cradles, including all iPad cradles. The included RAM's patented design dampens shock and vibration, helping to extend the life of your device. Overall Height: 7.35" Material: Powder Coated Marine Grade Aluminum Ball Size: 1.5" Rubber Ball Size Note: The "U" in the part number reflects product packaged in poly bag. If you prefer a smaller double socket arm with two round bases, RAM recommends the RAM-B-101U.

RAM Mount 1.5 Inch Ball Double Socket Arm with 2.5 Inch Round Base The RAM Mount RAM-103U mount, with standard arm, consists of the 1.5" diameter ball and socket system with one open socket end. This mount is designed to be used with any of the RAM mounting bases or cradles with a 1.5" diameter rubber ball. The RAM-202U round base has a 1.5" diameter rubber ball connected at right angles to a 2.5" diameter base. The plate has pre-drilled holes in the base, including the universal AMPS hole pattern. Material: Powder Coated Marine Grade Aluminum Ball Size: 1.5" Rubber Ball Size Note: The "U" in the part number reflects product packaged in poly bag.

Ram Mounts Looking for all the Ram Mount products we carry them. You can find them all right here in our Ram Mount Store Aqua Box Mount section. With everything from camera mounts to vehicle mounts including cell phone mounts, you will have plenty of choices to consider and options to choose from. Ram Mounting Systems is a quality manufacturer of all kinds of different mounts for your watercraft. You can get cell phone mounts and drink cup mounts here, along with GPS mounts and fishing rod holders. There are even iPad/iPhone/iPod mounts so you do not have to worry about having your electronics safe but close at hand.   If you have a kayak we have kayak mounts, too, and you can even do some work or surf the internet with laptop mounts to choose from. Of course, you want to make sure you choose a good marine electronics mount for your equipment, so you do not risk losing anything vital. Tablet mounts, swing arm mounts, surface mounts, and suction cup mounts are all available, and we have seat mounts, as well. You can even choose from motorcycle mounts, and rail/handle bar mounts to ensure you have everything you need your all of your future adventures.

RAM Flat Surface Horizontal Single Swing Arm Mount The RAM single swing arm mount consists of a 6" long BENT swing arm mounted on a horizontal surface mounting base. At the device mounting end of the mount is a rectangular 6.25" x 2" plate. There are two (2) pivoting points on the mount. One at the swing arm and base and one at the center of the rectangular plate and the end of the swing arm. Each pivoting point allows a complete 360 degree rotation. Dimensions: Center of knob to center of ball socket: 6" Overall length of swing arm assembly: 10.75" Overall height: 5.6" Height from base to top of knob: 4.91" Material: Powder Coated Marine Grade Aluminum Note:The "U" in the part number reflects product packaged in poly bag. The included plate is a universal mounting bracket with a selection of mounting hole locations. In certain applications additional holes may need to be drilled for proper fit with your electronic device.

RAM Handlebar Rail Mount with Zinc Coated U-Bolt Base, Short Double Socket Arm & Round Base Adapter that Contains a 1/4"-20 Thread for Cameras Part #: RAM-B-149ZA-C1U The RAM zinc coated u-bolt rail base consists of the 1" diameter ball and socket system with RAM Universal 1/4"-20 thread centered on a 2.5" diameter plate. This mount is designed to be a universal mounting solution for both still and moving cameras. The base has a 1.0" diameter rubber ball designed to sit at right angles to the mounting rail. The zinc coated metal u-bolt and nuts included will fit a circular rail with diameter from 0.5" to 1.25". To mount the rail base, place the top of the base on the rail and then slide the u-bolt around the rail, into the holes in the base top. Now tighten the screws onto the u-bolt until the base is clamped firmly. If you desire, you can now slot the black composite covers over the exposed ends of the u-bolt. Material: Powder Coated Marine Grade Aluminum Ball Size: 1" Rubber Ball "B" Size Note: The "U" in the part number reflects product packaged in poly bag. The male 1/4" long, 1/4"-20 thread in the middle of the 2.5" diameter plate will connect to the standard female thread found at the bottom of most still and video cameras.

Ram 1" Diameter Ball Mount with 2/2.5" Round Bases and Short Arm The RAM-B-101-A consists of a SHORT double socket arm and two 2.5" diameter round bases that contain the universal AMPS hole pattern. The mount is designed with a 1" diameter patented rubber ball and socket system that has adjustment points at both ends of the double socket arm; this allowing for almost infinite adjustment and perfect viewing angles. The hole pattern found on the round base adapter will connect to many RAM cradles, including all iPad cradles. The included RAM's patented design dampens shock and vibration, helping to extend the life of your device.

The RAM-D-201U-C, short double socket arm, has a socket at both ends that accommodates 2.25" ball bases. A single spring inside the arm opens the end sockets, allowing you to pivot the ball and socket connection. This socket technology allows for almost infinite adjustment and perfect viewing angles. Dimensions: Overall Length: 5.0625" Socket-To-Socket Length: 3.1875" Material: Powder Coated Marine Grade Aluminum Ball Size: 2.25" Rubber Ball "D" Size

RAM® Track Ball™ Double Ball Mount with Garmin Spine Clip Holder  The RAM® Spine Clip holder is a mount adapter that easily clips into the integrated spine connection on a wide variety of Garmin devices. This kit is compatible with virtually any track system including the RAM® Tough-Track™ and is easy to install and remove from your vehicle or vessel. Features: Kit includes RAM® Spine Clip Holder for Garmin, B size diamond ball base, medium double socket arm, and RAM® Track Ball™ base The holder secures any Garmin handheld device with an integrated spine connection Designed for most third-party track mounting systems; compatible with any RAM® Tough-Track™ Backed by a lifetime warranty Compatible Garmin Devices: Alpha® 100, Approach® G3, Approach® G5, Astro® 320, Astro® 430, Astro® 900, Dakota® 10, Dakota® 20, eTrex® 10, eTrex® 20, eTrex® 20x, eTrex® 22x, eTrex® 30, eTrex® 30x, eTrex® 32x, eTrex® Touch 25, eTrex® Touch 35, eTrex® Touch 35t, GPSMAP® 62, GPSMAP® 62s, GPSMAP® 62sc, GPSMAP® 62st, GPSMAP® 62stc, GPSMAP® 64, GPSMAP® 64s, GPSMAP® 64sc, GPSMAP® 65s, GPSMAP® 66i, GPSMAP® 66s, GPSMAP® 66st, GPSMAP® 79s, GPSMAP® 79sc, GPSMAP® 86 Series, inReach Explorer®+, inReach® Mini, inReach SE®, Oregon® 200, Oregon® 300, Oregon® 400c, Oregon® 400i, Oregon® 400t, Oregon® 450, Oregon® 450t, Oregon® 550, Oregon® 550t, Oregon® 600, Oregon® 600t, Oregon® 650, Oregon® 650t, Oregon® 700, Oregon® 750, Oregon® 750t, Rino® 610, Rino® 650, Rino® 650t, Rino® 655t, Rino® 700, Rino® 750, Rino® 755t, and Sport PRO™ Includes: Assembly Hardware (1) Friction Washer (1) 1/4"-20 x 7/8" T-Bolt Specifications: T-Bolt Dimensions (inch): .48" x .95" Socket to Socket Length (inch): 3" Ball Size: B Size (1") Weight: 0.41 lb. Materials: High-strength composite Weight Capacity:  Standard Use: 2 lbs Heavy-Duty Use: 1 lb

RAM® Tough-Tray™ Double Ball Mount with Double U-Bolt Rail Base The RAM-101-DAN1U consists of the RAM Tough-Tray™ with flat retaining arms, a standard length 6" double socket arm, and 1.5" diameter ball double u-bolt base. The RAM Tough-Tray™ is a spring-loaded expandable tray that can accommodate 10 to 16-inch-wide laptops. The tray includes four FLAT (4) side clamping arms, allowing a laptop to close completely while in the tray. These arms can be moved both vertically and horizontally. This allows for a custom fit for varying thicknesses of laptops and the freedom of not blocking ports or drives. Hole patterns on the perimeter of the tray facilitate the mounting of additional RAM systems to support GPS, phones, or other electronics. Specifications: Hardware Included: Assembly Hardware, (2) 1/4"-20 U-Bolts for 1" - 1.25" Rails, (4) 1/4"-20 Nylock Nuts, (4) Rubber CapsHolder  Tray Dimensions: Width Range: 10" - 16", Side Arm Clamp Height: .5" - 1.75", Tray Depth: 10", Tray Clamp Range: 1" - 1.25" diameter Socket 2 Socket Length: 4.66" Ball Size: C size (1.5") Weight Capacity: Standard Use: 4 lbs, Heavy-Duty Use: 3 lb Materials: Marine-grade aluminum and high-strength composite Packaging Type: Polybag Weight: 4.15 lbs.

Low Profile Composite Double Socket Arm The RAP-B-201U, composite standard double socket arm, has a socket at both ends that accommodates 1" ball bases. A single spring inside the arm opens the end sockets, allowing you to pivot the ball and socket connection. This socket technology allows for almost infinite adjustment and perfect viewing angles.  Features: Material: High Strength Composite Ball Size: B Size 1" Rubber Ball Note: The "U" in the part number reflects product packaged in poly bag Dimensions: Overall Length: 2.75" Socket-To-Socket Length: 2"

Composite Drill-Down Double Ball Mount with Rectangle AMPS Plates  This composite drill-down double ball mount features two AMPS hole pattern bases with 1" diameter balls. Each base has four pre-drilled holes at each corner with 1.5" x 1.188" hole spacing. These bases attach directly to the included short double socket arm. Take advantage of the RAM® double ball and socket system for near-infinite adjustability to achieve a perfect viewing angle for your mounted device.  Dimensions: Overall Height: 4.1" Material: High-Strength Composite Ball Size: B Size 1" Rubber Ball Note: The "U" in the part number reflects product packaged in poly bag.

Description: The RAP-201U, standard double socket arm, has a socket at both ends that accommodates 1.5" ball bases. A single spring inside the arm opens the end sockets, allowing you to pivot the ball and socket connection. This socket technology allows for almost infinite adjustment and perfect viewing angles. Dimensions: Overall Length: 5.625" Socket-To-Socket Length: 4.5" Material: High Strength Composite Ball Size: 1.5" Rubber Ball Size