RAM Motorcycle Brake/Clutch Reservoir Base with (2 Quantity) 1" Balls The RAM-B-309-2U connects to your handlebar clutch/brake clamp, left or right side, and holds two 1" diameter mounting ball. The ball that is connected between the hole centers is removable. The base fits the control clamps on your motorcycle with 40mm x 6mm stainless steel hardware, provided in the kit. To see if the RAM-B-309-2U base will mount to your motorcycle, check the hole spacing of the base against your clutch/brake reservoir. The holes centers have a minimum width of 0.94" and a maximum of 1.58". Material: Powder Coated Marine Grade Aluminum Ball Size: 1" Rubber Ball "B" Size Note: The "U" in the part number reflects product packaged in poly bag.

RAM Chrome Motorcycle Brake/Clutch Reservoir Base w/1" Ball The RAM-B-309-1CHU connects to your handlebar clutch/brake clamp, left or right side, and holds one 1" diameter mounting ball. The chrome base fits the control clamps on your motorcycle with 40mm x 6mm stainless steel hardware, provided in the kit. To see if the RAM-B-309-1CHU base will mount to your motorcycle, check the hole spacing of the base against your clutch/brake reservoir. The holes centers have a minimum width of 0.94" and a maximum of 1.58". Material: Powder Coated Marine Grade Aluminum Ball Size: 1" Rubber Ball "B" Size Note: The "U" in the part number reflects product packaged in poly bag.

RAM Motorcycle Brake/Clutch Reservoir Base w/1" Ball The RAM-B-309-1U connects to your handlebar clutch/brake clamp, left or right side, and holds one 1" diameter mounting ball. The base fits the control clamps on your motorcycle with 40mm x 6mm stainless steel hardware, provided in the kit. To see if the RAM-B-309-1U base will mount to your motorcycle, check the hole spacing of the base against your clutch/brake reservoir. The holes centers have a minimum width of 0.94" and a maximum of 1.58". Material: Powder Coated Marine Grade Aluminum Ball Size: 1" Rubber Ball "B" Size Note: The "U" in the part number reflects product packaged in poly bag.

X-Grip® Phone Mount with Motorcycle Brake/Clutch Reservoir Base The RAM-B-174-A-UN7 consists of hardware for mounting to either brake/clutch reservoirs and rails that are 0.5" to 1.25" in diameter, short length double socket arm and universal X-Grip® cell phone cradle. Designed into the mount is a 1" diameter patented rubber ball and socket system with adjustment points at both ends of the socket arm; this with a twist of the arm knob, allows you to move the X-Grip® mount to your optimum viewing position. The mounting hardware for brake/clutch reservoirs include both standard and metric mounting bolts. The included X-Grip® cradle has a clean and clever four leg design that sports great holding power without hiding your phone behind foam pads and plastic. The spring loaded X-Grip® cradle expands and contracts, allowing for a perfect custom fit of your cell phone. The perfect complement to the modern sleek interior of today's vehicles, the RAM X-Grip® is the cell phone cradle evolved. The X-Grip® includes a device tether recommended for outdoor applications. The cradle is compatible with handheld devices that will fit the dimensions listed below. It is important to verify the dimensions of your handheld device with a case/sleeve/skin when determining the overall size.  Specifications: Cradle Dimensions: Minimum Width = 1.875" (Minimum Height = 4.25") Maximum Width = 3.25" (Minimum Height = 2.25") Depth = 0.875" Includes: (QTY. 1), Optional Tether Included Material: Powder Coated Marine Grade Aluminum, Marine Grade Stainless Steel Components & High Strength Composite Ball Size: B Size 1" Rubber Ball Note: The "U" in the part number reflects product packaged in poly bag. To see if the RAM-B-174-UN7 will mount to your motorcycle, check the hole spacing of the base against your clutch/brake reservoir. The holes centers have a minimum width of 0.94" and a maximum of 1.58". RAM highly recommends using the provided Tether for all open cockpit applications while using this product. Weight: 0.88 lbs.

RAM Motorcycle Brake/Clutch Reservoir Cover Base with 1" Ball Offset The RAM-B-346U base fits cleanly over your existing brake/clutch reservoir cover with the 1" ball offset. Made of die cast aluminum with an over molded rubber ball, both form and function are unsurpassed. Installation is simple and all necessary hardware is included. Material: Powder Coated Marine Grade Aluminum Ball Size: 1" Rubber Ball "B" Size Note: The "U" in the part number reflects product packaged in poly bag.

RAM Motorcycle Combination Base for Handlebar or Brake/Clutch Reservoir with Two 1" Balls The RAM combination handlebar and brake/clutch reservoir base provides the ultimate flexibility for mounting. Mount to either your handlebar or brake/clutch, almost infinite adjustment and perfect viewing angles are providing in this kit. Hardware: Standard or metric thread stainless steel bolts, provided in the kit. The zinc coated metal u-bolt accommodates rails in diameter from 0.75" to 1.25" in diameter. Material: Powder Coated Marine Grade Aluminum Ball Size: 1" Rubber Ball "B" Size Note: The "U" in the part number reflects product packaged in poly bag.

X-Grip® Large Phone Mount with Brake/Clutch Reservoir Base The RAM-B-174-UN10 consists of hardware for mounting to either brake/clutch reservoirs and rails that are 0.5" to 1.25" in diameter, double socket arm and universal X-Grip® large phone/phablet holder. Designed into the mount is a 1" diameter patented rubber ball and socket system with adjustment points at both ends of the socket arm; this with a twist of the arm knob, allows you to move the X-Grip® mount to your optimum viewing position. The mounting hardware for brake/clutch reservoirs include both standard and metric mounting bolts. The included X-Grip® cradle has a clean and clever four leg design that sports great holding power without hiding your phone behind foam pads and plastic. The spring loaded X-Grip® cradle expands and contracts, allowing for a perfect custom fit of your cell phone. The perfect complement to the modern sleek interior of today's vehicles, the RAM X-Grip® is the cell phone cradle evolved. The X-Grip® includes a device tether recommended for outdoor applications. The cradle is compatible with handheld devices that will fit the dimensions listed below. It is important to verify the dimensions of your handheld device with a case/sleeve/skin when determining the overall size.  Specifications: Includes: (QTY. 1), Optional Tether Included Cradle Dimensions: Minimum Width = 1.75" (Minimum Height = 5.5") Maximum Width = 4.5" (Minimum Height = 3.25") Depth = 0.875" Material: Powder Coated Marine Grade Aluminum, Marine Grade Stainless Steel Components & High Strength Composite Ball Size: B Size 1" Rubber Ball Note: Part number reflects product packaged in a retail box for store shelf display. To see if the RAM-B-174-UN7 will mount to your motorcycle, check the hole spacing of the base against your clutch/brake reservoir. The holes centers have a minimum width of 0.94" and a maximum of 1.58". RAM highly recommends using the provided Tether for all open cockpit applications while using this product. Weight: 1.0 lbs.

RAM Universal Finger Grip Holder Brake/Clutch Reservoir Mount Part #: RAM-B-184-UN4U The base consists of a 1" diameter rubber ball, hardware for mounting to both brake/clutch reservoirs and rails that are 0.5" to 1.25" in diameter. The mounting hardware for brake/clutch reservoirs include both standard and metric mounting bolts. Multiple pivot points, rubber ball and socket technology allows for almost infinite adjustment and perfect viewing angles. High quality materials insure your device is safe, secure, and within easy reach. The RAM Composite Universal Finger Grip™ Holder is designed to hold a large amount of cell phones and electronic devices. The holder comes with (3 sets) of four flexible rubber coated fingers placed along sides to grip your device. The fingers open by squeezing the ends to open the small finger arms. The bottom of the holder includes a back plate that adds support to the device being held by the mount. This mount is designed to hold the following devices: Cell Phones 2-Way Radios GPS Devices Height Dimensions: Minimum with Top and Bottom Plates: 5.25" Maximum with Top and Bottom Plates: 6.0" The top and bottom plates can be removed for larger devices. Spine Plate Dimensions: 2.5W x 5.0H" Using Short Arm Side Clamps: Maximum Depth: 0.75" Minimum Width: 1.25" Maximum Width: 3.0" Using Medium Arm Side Clamps: Maximum Depth: 1.25" Minimum Width: 1.5" Maximum Width: 3.5" Using Long Arm Side Clamps: Maximum Depth: 1.6" Minimum Width: 2.25" Maximum Width: 3.5" Included with Purchase: (1 qty) Universal Finger Grip™ holder (1 qty) Base/ball adaptor (attaches directly to cradle) (1 qty) Standard size double socket arm (1 qty) Mounting base (mounts to either brake/clutch reservoir or rail/handlebar) Hardware for mounting to either brake/clutch reservoir or rail/handlebar Material: High Strength Composite and Powder Coated Marine Grade Aluminum Ball Size: 1" Rubber Ball "B" Size Note: *The RAM-B-174-UN4U can mount to both the brake/clutch reservoir or any round rail that is 0.5" to 1.25" in diameter.The "U" in the part number reflects product packaged in poly bag. To see if the RAM-B-174-UN4U base will mount to your motorcycle, check the hole spacing of the base against your clutch/brake reservoir. The holes centers have a minimum width of 0.94" and a maximum of 1.58".

RAM Universal X-Grip Holder Brake/Clutch Reservoir Mount Part #: RAM-B-174-UN7 The RAM-B-174-UN7 consists of a double socket arm, hardware for mounting to both brake/clutch reservoirs and rails that are 0.5" to 1.25" in diameter and universal X-Grip™ cell phone holder. Designed into the mount is a 1" diameter patented rubber ball and socket system with adjustment points at both ends of the double socket arm. With a twist of the arm knob, you can move the cell phone holder to your optimum viewing position. The spring loaded X-Grip™ has a clean and clever four leg design that sports great holding power without hiding your phone behind foam pads and plastic. X-Grip™ Holder Features: 1. Spring loaded holder expands and contracts for perfect fit of your device 2. Rubber coated tips will hold device firm and stable X-Grip™ Holder Dimensions: Minimum Width = 0.875" (Devices at 0.875" must be a minimum of 4" in height to fit into holder) Maximum Width = 3.25" Depth = 0.875" Material: High Strength Composite & Powder Coated Marine Grade Aluminum Ball Size: 1" Rubber Ball "B" Size Note: Note: Part number reflects product packaged in clear clam shell for store shelf display. To see if the RAM-B-174-UN7 will mount to your motorcycle, check the hole spacing of the base against your clutch/brake reservoir. The holes centers have a minimum width of 0.94" and a maximum of 1.58".

RAM Motorcycle 1" Ball Adapter for Brake/Clutch Reservoir Base This ball connects to the open hole on the side of the RAM-B-309-1U (single 1" ball) and is included with the purchase of the RAM-B-309-2U (double 1" ball). Material: Powder Coated Marine Grade Aluminum Ball Size: 1" Rubber Ball "B" Size Note: The "U" in the part number reflects product packaged in poly bag.

RAM Motorcycle Brake/Clutch Reservoir Cover Base with 1" Ball Centered The RAM-B-345U brake/clutch reservoir cover base fits cleanly over your existing reservoir cover with the 1" ball centered. Made of die cast aluminum with an over molded rubber ball, both form and function are unsurpassed. Installation is simple and all necessary hardware is included. Material: Powder Coated Marine Grade Aluminum Ball Size: 1" Rubber Ball "B" Size Note: The "U" in the part number reflects product packaged in poly bag.

2" x 5" Rectangle Base with 2.25" Ball The RAM-D-202U-25 consists of a 2.25" diameter rubber ball connected at right angles to a 2" x 5" rectangular base. This mount has pre-drilled holes at each corner of the base. Features: Material: Powder Coated Marine Grade Aluminum Ball Size: 2.25" Rubber Ball Size Weight: 0.69 lbs.

11" x 3" Rectangle Universal Electronics Base with 2.25" Ball The RAM-D-111BU, universal mounting plate, consists of a 2.25" diameter rubber ball, connected at right angles to a flat 11" x 3" rectangular plate. The plate contains different combinations of pre-drilled holes which will match up to many electronic devices. Features: Material: Powder Coated Marine Grade Aluminum Ball Size: 2.25" Rubber "D" Ball Size Weight: 1.25 lbs. *Note: The "U" in the part number reflects product packaged in poly bag. This plate is a universal mounting bracket with a selection of mounting hole locations. In certain applications additional holes may need to be drilled for proper fit with your electronic device.

2" x 3" Rectangle Base with 2.25" Ball Contains a 2.25" diameter rubber ball connected at right angles to a 2" x 3" rectangular base. This mount has pre-drilled holes at each corner of the base.

Combination Brake/Clutch Reservoir U-Bolt Mount w/Universal X-Grip® Cell/iPhone Cradle The RAM-B-174-UN7U consists of hardware for mounting to either brake/clutch reservoirs and rails that are 0.5" to 1.25" in diameter, double socket arm and universal X-Grip® cell phone cradle. Designed into the mount is a 1" diameter patented rubber ball and socket system with adjustment points at both ends of the socket arm; this with a twist of the arm knob, allows you to move the X-Grip® mount to your optimum viewing position. The mounting hardware for brake/clutch reservoirs include both standard and metric mounting bolts. The included X-Grip® cradle has a clean and clever four leg design that sports great holding power without hiding your phone behind foam pads and plastic. The spring loaded X-Grip® cradle expands and contracts, allowing for a perfect custom fit of your cell phone. The perfect complement to the modern sleek interior of today's vehicles, the RAM X-Grip® is the cell phone cradle evolved. The X-Grip® includes a device tether recommended for outdoor applications. The cradle is compatible with handheld devices that will fit the dimensions listed below. It is important to verify the dimensions of your handheld device with a case/sleeve/skin when determining the overall size. Cradle Dimensions Minimum Width = 1.875" (Minimum Height = 4.25") Maximum Width = 3.25" (Minimum Height = 2.25") Depth = 0.875" Features: Rustproof High strength composite and stainless steel construction Spring loaded cradle expands and contracts for perfect fit of your device Rubber coated tips will hold device firm and stable Socket technology allows for multiple adjustment angles and articulation of device Includes Tether for open cockpit and extreme environments Lifetime warranty Made in U.S.A. Material: Powder Coated Marine Grade Aluminum, Marine Grade Stainless Steel Components & High Strength Composite Ball Size: 1" Rubber Ball "B" Size Note: The "U" in the part number reflects product packaged in poly bag. To see if the RAM-B-174-UN7U will mount to your motorcycle, check the hole spacing of the base against your clutch/brake reservoir. The holes centers have a minimum width of 0.94" and a maximum of 1.58". RAM highly recommends using the provided Tether for all open cockpit applications while using this product.