RAM Universal Finger Grip Holder Brake/Clutch Reservoir Mount Part #: RAM-B-184-UN4U The base consists of a 1" diameter rubber ball, hardware for mounting to both brake/clutch reservoirs and rails that are 0.5" to 1.25" in diameter. The mounting hardware for brake/clutch reservoirs include both standard and metric mounting bolts. Multiple pivot points, rubber ball and socket technology allows for almost infinite adjustment and perfect viewing angles. High quality materials insure your device is safe, secure, and within easy reach. The RAM Composite Universal Finger Grip™ Holder is designed to hold a large amount of cell phones and electronic devices. The holder comes with (3 sets) of four flexible rubber coated fingers placed along sides to grip your device. The fingers open by squeezing the ends to open the small finger arms. The bottom of the holder includes a back plate that adds support to the device being held by the mount. This mount is designed to hold the following devices: Cell Phones 2-Way Radios GPS Devices Height Dimensions: Minimum with Top and Bottom Plates: 5.25" Maximum with Top and Bottom Plates: 6.0" The top and bottom plates can be removed for larger devices. Spine Plate Dimensions: 2.5W x 5.0H" Using Short Arm Side Clamps: Maximum Depth: 0.75" Minimum Width: 1.25" Maximum Width: 3.0" Using Medium Arm Side Clamps: Maximum Depth: 1.25" Minimum Width: 1.5" Maximum Width: 3.5" Using Long Arm Side Clamps: Maximum Depth: 1.6" Minimum Width: 2.25" Maximum Width: 3.5" Included with Purchase: (1 qty) Universal Finger Grip™ holder (1 qty) Base/ball adaptor (attaches directly to cradle) (1 qty) Standard size double socket arm (1 qty) Mounting base (mounts to either brake/clutch reservoir or rail/handlebar) Hardware for mounting to either brake/clutch reservoir or rail/handlebar Material: High Strength Composite and Powder Coated Marine Grade Aluminum Ball Size: 1" Rubber Ball "B" Size Note: *The RAM-B-174-UN4U can mount to both the brake/clutch reservoir or any round rail that is 0.5" to 1.25" in diameter.The "U" in the part number reflects product packaged in poly bag. To see if the RAM-B-174-UN4U base will mount to your motorcycle, check the hole spacing of the base against your clutch/brake reservoir. The holes centers have a minimum width of 0.94" and a maximum of 1.58".

RAM Universal X-Grip Holder Brake/Clutch Reservoir Mount Part #: RAM-B-174-UN7 The RAM-B-174-UN7 consists of a double socket arm, hardware for mounting to both brake/clutch reservoirs and rails that are 0.5" to 1.25" in diameter and universal X-Grip™ cell phone holder. Designed into the mount is a 1" diameter patented rubber ball and socket system with adjustment points at both ends of the double socket arm. With a twist of the arm knob, you can move the cell phone holder to your optimum viewing position. The spring loaded X-Grip™ has a clean and clever four leg design that sports great holding power without hiding your phone behind foam pads and plastic. X-Grip™ Holder Features: 1. Spring loaded holder expands and contracts for perfect fit of your device 2. Rubber coated tips will hold device firm and stable X-Grip™ Holder Dimensions: Minimum Width = 0.875" (Devices at 0.875" must be a minimum of 4" in height to fit into holder) Maximum Width = 3.25" Depth = 0.875" Material: High Strength Composite & Powder Coated Marine Grade Aluminum Ball Size: 1" Rubber Ball "B" Size Note: Note: Part number reflects product packaged in clear clam shell for store shelf display. To see if the RAM-B-174-UN7 will mount to your motorcycle, check the hole spacing of the base against your clutch/brake reservoir. The holes centers have a minimum width of 0.94" and a maximum of 1.58".

RAM Universal Finger Grip Holder Suction Cup Mount Part #: RAM-B-166-UN4U Suction Cup Twist Lock Mount Description: RAM suction cup twist lock ball and socket technology allows for almost infinite adjustment and perfect viewing angles. High quality materials insure your device is safe, secure, and within easy reach. RAM's patented design also dampens shock and vibration helping to extend the life of your mobile device. Universal Finger Grip™ Holder Description:The RAM Composite Universal Finger Grip™ Holder is designed to hold a large amount of cell phones and electronic devices. The holder comes with (3 sets) of four flexible rubber coated fingers placed along sides to grip your device. The fingers open by squeezing the ends to open the small finger arms. The bottom of the holder includes a back plate that adds support to the device being held by the mount. This mount is designed to hold the following devices: Cell Phones 2-Way Radios GPS Devices Height Dimensions: Minimum with Top and Bottom Plates: 5.25" Maximum with Top and Bottom Plates: 6.0" The top and bottom plates can be removed for larger devices. Spine Plate Dimensions: 2.5W x 5.0H" Using Short Arm Side Clamps: Maximum Depth: 0.75" Minimum Width: 1.25" Maximum Width: 3.0" Using Medium Arm Side Clamps: Maximum Depth: 1.25" Minimum Width: 1.5" Maximum Width: 3.5" Using Long Arm Side Clamps: Maximum Depth: 1.6" Minimum Width: 2.25" Maximum Width: 3.5" Material: High Strength Composite and Powder Coated Marine Grade Aluminum Ball Size: 1" Rubber Ball "B" Size Note: The "U" in the part number reflects product packaged in poly bag

RAM Univeral Finger Grip Holder ATV/UTV Strap Mount Part #: RAM-B-149Z-2-UN4 Whether your UTV or ATV is bone stock or loaded with accessory racks and guards, the new RAM Strap Base lets you choose the best possible mounting location for almost anything. Designed for a clean installation, this base accommodates most common tubing sizes on UTV?s and ATV's, allowing for the placement of the RAM rubber ball base. Safely concealing a strap clamp in a compact housing, you won't have to worry about exposed sharp edges or unwanted loosening. With the ball base in place, you have the foundation for mounting everything from GPS, Cell Phones, Radios, or maybe the famous RAM self leveling drink cup holder. No matter what you choose to do with it, you'll wonder why your UTV or ATV didn?t come from the factory with this must-have product. Strap Dimensions: 1.57" (40mm) to a maximum of 3.15" (80mm) Universal Finger Grip™ Holder Description: The RAM Composite Universal Finger Grip™ Holder is designed to hold a large amount of cell phones and electronic devices. The holder comes with (3 sets) of four flexible rubber coated fingers placed along sides to grip your device. The fingers open by squeezing the ends to open the small finger arms. The bottom of the holder includes a back plate that adds support to the device being held by the mount. The spine plate contains the universal AMPs and 1.5" x 2" hole patterns. This mount is designed to hold the following devices: Cell Phones 2-Way Radios GPS Devices Height Dimensions: Minimum with Top and Bottom Plates: 5.25" Maximum with Top and Bottom Plates: 6.0" The top and bottom plates can be removed for larger devices. Spine Plate Dimensions: 3" Width x 3" Height Using Short Arm Side Clamps: Maximum Depth: 0.75" Minimum Width: 1.25" Maximum Width: 3.0" Using Medium Arm Side Clamps: Maximum Depth: 1.25" Minimum Width: 1.5" Maximum Width: 3.5" Using Long Arm Side Clamps: Maximum Depth: 1.6" Minimum Width: 2.25" Maximum Width: 3.5" Material: High Strength Composite and Powder Coated Marine Grade Aluminum Ball Size: 1" Rubber Ball "B" Size Note: Part number reflects product packaged in clear clam shell for store shelf display.

RAM Mount Universal Finger Grip Holder Surface Mount Part #: RAM-B-138-UN4 Simply choose the base mounting hardware and the possibilities become endless with a RAM flat surface mount. Four mounting holes in the round ball base easily accommodate up to a #10 screw. Rubber ball and socket technology allows for almost infinite adjustment and perfect viewing angles. High quality materials insure your device is safe, secure, and within easy reach. RAM's patented design also dampens shock and vibration helping to extend the life of your mobile device. Universal Finger Grip™ Holder Description: The RAM Composite Universal Finger Grip™ Holder is designed to hold a large amount of cell phones and electronic devices. The holder comes with (3 sets) of four flexible rubber coated fingers placed along sides to grip your device. The fingers open by squeezing the ends to open the small finger arms. The bottom of the holder includes a back plate that adds support to the device being held by the mount. This mount is designed to hold the following devices: Cell Phones 2-Way Radios GPS Devices Height Dimensions: Minimum with Top and Bottom Plates: 5.25" Maximum with Top and Bottom Plates: 6.0" The top and bottom plates can be removed for larger devices. Spine Plate Dimensions: 2.5W x 5.0H" Using Short Arm Side Clamps: Maximum Depth: 0.75" Minimum Width: 1.25" Maximum Width: 3.0" Using Medium Arm Side Clamps: Maximum Depth: 1.25" Minimum Width: 1.5" Maximum Width: 3.5" Using Long Arm Side Clamps: Maximum Depth: 1.6" Minimum Width: 2.25" Maximum Width: 3.5" Material: High Strength Composite and Powder Coated Marine Grade Aluminum Note: Part number reflects product packaged in clear clam shell for store shelf display.

RAM Universal Finger Grip Holder Handlebar Rail Mount Part #: RAM-B-149Z-UN4U Motorcycle Handlebar Mount Description: The motorcycle mount makes attaching to handlebars, tubing, or railing a breeze. Simple to install and easy to use, the possibilities become endless. Rubber ball and socket technology allows for almost infinite adjustment and perfect viewing angles. High quality materials insure your device is safe, secure, and within easy reach. RAM?s patented design also dampens shock and vibration helping to extend the life of your mobile device. Included in this package is hardware for tubing that is 0.50" to 1.25" in diameter. Universal Finger Grip™ Holder Description: The RAM Composite Universal Finger Grip™ Holder is designed to hold a large amount of cell phones and electronic devices. The holder comes with (3 sets) of four flexible rubber coated fingers placed along sides to grip your device. The fingers open by squeezing the ends to open the small finger arms. The bottom of the holder includes a back plate that adds support to the device being held by the mount. The spine plate contains the universal AMPs and 1.5" x 2" hole patterns. This mount is designed to hold the following devices: Cell Phones 2-Way Radios GPS Devices Height Dimensions: Minimum with Top and Bottom Plates: 5.25" Maximum with Top and Bottom Plates: 6.0" The top and bottom plates can be removed for larger devices. Spine Plate Dimensions: 3" Width x 3" Height Using Short Arm Side Clamps: Maximum Depth: 0.75" Minimum Width: 1.25" Maximum Width: 3.0" Using Medium Arm Side Clamps: Maximum Depth: 1.25" Minimum Width: 1.5" Maximum Width: 3.5" Using Long Arm Side Clamps: Maximum Depth: 1.6" Minimum Width: 2.25" Maximum Width: 3.5" Material: High Strength Composite and Powder Coated Marine Grade Aluminum Ball Size: 1" Rubber Ball "B" Size Note: The "U" in the part number reflects product packaged in poly bag

RAM Universal Finger-Grip™ Phone/Radio Holder The RAM Composite Universal Finger Grip Holder is designed to hold a large amount of cell phones and electronic devices. The holder comes with (3 sets) of four flexible rubber coated fingers placed along sides to grip your device. The fingers open by squeezing the ends to open the small finger arms. The bottom of the holder includes a back plate that adds support to the device being held by the mount. This mount is designed to hold the following devices: Cell Phones 2-Way Radios GPS Devices Height Dimensions: Minimum with Top and Bottom Plates: 5.25" Maximum with Top and Bottom Plates: 6.0" The top and bottom plates can be removed for larger devices. Spine Plate Dimensions: 2.5W x 5.0H" Using Short Arm Side Clamps: Maximum Depth: 0.75" Minimum Width: 1.25" Maximum Width: 3.0" Using Medium Arm Side Clamps: Maximum Depth: 1.25" Minimum Width: 1.5" Maximum Width: 3.5" Using Long Arm Side Clamps: Maximum Depth: 1.6" Minimum Width: 2.25" Maximum Width: 3.5" Material: High Strength Composite Note: The "U" in the part number reflects product packaged in poly bag.

RAM Universal Finger Grip Glare Shield Clamp Mount Part #: RAM-B-177UN4 The RAM-B-177-UN4 consists of a glare shield clamp base, double socket arm and universal Finger Grip™ holder. Simply locate the clamp on any clamping surface up to 1.12" thick and gently snug the nylon thumb screws. The double ball & socket system will provide perfect viewing angles to get the most from your electronic device. The RAM glare shield clamp with double ball & socket system is far and away the most discrete and clean way to mount most any compact electronic device to the glare shield of your aircraft. The RAM Composite Universal Finger Grip™ Holder is designed to hold a large amount of cell phones and electronic devices. The holder comes with (3 sets) of four flexible rubber coated fingers placed along sides to grip your device. The fingers open by squeezing the ends to open the small finger arms. The bottom of the holder includes a back plate that adds support to the device being held by the mount. The perfect solution that is the best phone mount, car mount, motorcycle mount and can be used with several other phone accessories including samsung accessories and lg accessories. The spine plate contains the universal AMPs and 1.5" x 2" hole patterns. This mount is designed to hold the following devices: Cell Phones (check measurements below for dimensions) 2-Way Radios GPS Devices Works with OtterBox (Defender, Commuter, Impact) Cases, Phones with Bumper, Twisted Metal Case and More Perfect rugged solution for the Blackberry, HTC Evo, Droid X, iPhone, and More Use on your Motorcycle, ATV, UTV, Car, Boat and More Mount will attach to flat surfaces with the following dimensions: Min: 4.4mm / 0.17" Max: 28.0mm / 1.12" Material: High Strength Composite & Powder Coated Marine Grade Aluminum Ball Size: 1" Rubber Ball "B" Size Note: Part number reflects product packaged in clear clam shell for store shelf display.

RAM Motorcycle Brake/Clutch Reservoir Cover Base with 1" Ball Offset The RAM-B-346U base fits cleanly over your existing brake/clutch reservoir cover with the 1" ball offset. Made of die cast aluminum with an over molded rubber ball, both form and function are unsurpassed. Installation is simple and all necessary hardware is included. Material: Powder Coated Marine Grade Aluminum Ball Size: 1" Rubber Ball "B" Size Note: The "U" in the part number reflects product packaged in poly bag.

X-Grip® Large Phone Mount with Brake/Clutch Reservoir Base The RAM-B-174-UN10 consists of hardware for mounting to either brake/clutch reservoirs and rails that are 0.5" to 1.25" in diameter, double socket arm and universal X-Grip® large phone/phablet holder. Designed into the mount is a 1" diameter patented rubber ball and socket system with adjustment points at both ends of the socket arm; this with a twist of the arm knob, allows you to move the X-Grip® mount to your optimum viewing position. The mounting hardware for brake/clutch reservoirs include both standard and metric mounting bolts. The included X-Grip® cradle has a clean and clever four leg design that sports great holding power without hiding your phone behind foam pads and plastic. The spring loaded X-Grip® cradle expands and contracts, allowing for a perfect custom fit of your cell phone. The perfect complement to the modern sleek interior of today's vehicles, the RAM X-Grip® is the cell phone cradle evolved. The X-Grip® includes a device tether recommended for outdoor applications. The cradle is compatible with handheld devices that will fit the dimensions listed below. It is important to verify the dimensions of your handheld device with a case/sleeve/skin when determining the overall size.  Specifications: Includes: (QTY. 1), Optional Tether Included Cradle Dimensions: Minimum Width = 1.75" (Minimum Height = 5.5") Maximum Width = 4.5" (Minimum Height = 3.25") Depth = 0.875" Material: Powder Coated Marine Grade Aluminum, Marine Grade Stainless Steel Components & High Strength Composite Ball Size: B Size 1" Rubber Ball Note: Part number reflects product packaged in a retail box for store shelf display. To see if the RAM-B-174-UN7 will mount to your motorcycle, check the hole spacing of the base against your clutch/brake reservoir. The holes centers have a minimum width of 0.94" and a maximum of 1.58". RAM highly recommends using the provided Tether for all open cockpit applications while using this product. Weight: 1.0 lbs.

Combination Brake/Clutch Reservoir U-Bolt Mount w/Universal X-Grip® Cell/iPhone Cradle The RAM-B-174-UN7U consists of hardware for mounting to either brake/clutch reservoirs and rails that are 0.5" to 1.25" in diameter, double socket arm and universal X-Grip® cell phone cradle. Designed into the mount is a 1" diameter patented rubber ball and socket system with adjustment points at both ends of the socket arm; this with a twist of the arm knob, allows you to move the X-Grip® mount to your optimum viewing position. The mounting hardware for brake/clutch reservoirs include both standard and metric mounting bolts. The included X-Grip® cradle has a clean and clever four leg design that sports great holding power without hiding your phone behind foam pads and plastic. The spring loaded X-Grip® cradle expands and contracts, allowing for a perfect custom fit of your cell phone. The perfect complement to the modern sleek interior of today's vehicles, the RAM X-Grip® is the cell phone cradle evolved. The X-Grip® includes a device tether recommended for outdoor applications. The cradle is compatible with handheld devices that will fit the dimensions listed below. It is important to verify the dimensions of your handheld device with a case/sleeve/skin when determining the overall size. Cradle Dimensions Minimum Width = 1.875" (Minimum Height = 4.25") Maximum Width = 3.25" (Minimum Height = 2.25") Depth = 0.875" Features: Rustproof High strength composite and stainless steel construction Spring loaded cradle expands and contracts for perfect fit of your device Rubber coated tips will hold device firm and stable Socket technology allows for multiple adjustment angles and articulation of device Includes Tether for open cockpit and extreme environments Lifetime warranty Made in U.S.A. Material: Powder Coated Marine Grade Aluminum, Marine Grade Stainless Steel Components & High Strength Composite Ball Size: 1" Rubber Ball "B" Size Note: The "U" in the part number reflects product packaged in poly bag. To see if the RAM-B-174-UN7U will mount to your motorcycle, check the hole spacing of the base against your clutch/brake reservoir. The holes centers have a minimum width of 0.94" and a maximum of 1.58". RAM highly recommends using the provided Tether for all open cockpit applications while using this product.

X-Grip® Phone Mount with Motorcycle Brake/Clutch Reservoir Base The RAM-B-174-A-UN7 consists of hardware for mounting to either brake/clutch reservoirs and rails that are 0.5" to 1.25" in diameter, short length double socket arm and universal X-Grip® cell phone cradle. Designed into the mount is a 1" diameter patented rubber ball and socket system with adjustment points at both ends of the socket arm; this with a twist of the arm knob, allows you to move the X-Grip® mount to your optimum viewing position. The mounting hardware for brake/clutch reservoirs include both standard and metric mounting bolts. The included X-Grip® cradle has a clean and clever four leg design that sports great holding power without hiding your phone behind foam pads and plastic. The spring loaded X-Grip® cradle expands and contracts, allowing for a perfect custom fit of your cell phone. The perfect complement to the modern sleek interior of today's vehicles, the RAM X-Grip® is the cell phone cradle evolved. The X-Grip® includes a device tether recommended for outdoor applications. The cradle is compatible with handheld devices that will fit the dimensions listed below. It is important to verify the dimensions of your handheld device with a case/sleeve/skin when determining the overall size.  Specifications: Cradle Dimensions: Minimum Width = 1.875" (Minimum Height = 4.25") Maximum Width = 3.25" (Minimum Height = 2.25") Depth = 0.875" Includes: (QTY. 1), Optional Tether Included Material: Powder Coated Marine Grade Aluminum, Marine Grade Stainless Steel Components & High Strength Composite Ball Size: B Size 1" Rubber Ball Note: The "U" in the part number reflects product packaged in poly bag. To see if the RAM-B-174-UN7 will mount to your motorcycle, check the hole spacing of the base against your clutch/brake reservoir. The holes centers have a minimum width of 0.94" and a maximum of 1.58". RAM highly recommends using the provided Tether for all open cockpit applications while using this product. Weight: 0.88 lbs.

RAM Brake Clutch Reservoir Cover Motorcycle Mount (1" Ball Centered) The RAM-B-182U consists of a centered brake/clutch reservoir cover base, double socket arm and diamond adapter base. The diamond adapter base has a hole pattern that matches the industry standard AMPS hole pattern and will connect to a large variety of RAM Mount and third party cradles. Designed into the mount is a 1" diameter patented rubber ball and socket system with adjustment points at the base and cradle. With a twist of the arm knob, you can move the reservoir cover mount to your optimum viewing position. Material: Powder Coated Marine Grade Aluminum Ball Size: 1" Rubber Ball "B" Size Note: The "U" in the part number reflects product packaged in poly bag.

RAM Motorcycle Brake/Clutch Reservoir Base w/1" Ball The RAM-B-309-1U connects to your handlebar clutch/brake clamp, left or right side, and holds one 1" diameter mounting ball. The base fits the control clamps on your motorcycle with 40mm x 6mm stainless steel hardware, provided in the kit. To see if the RAM-B-309-1U base will mount to your motorcycle, check the hole spacing of the base against your clutch/brake reservoir. The holes centers have a minimum width of 0.94" and a maximum of 1.58". Material: Powder Coated Marine Grade Aluminum Ball Size: 1" Rubber Ball "B" Size Note: The "U" in the part number reflects product packaged in poly bag.

RAM Motorcycle Combination Base for Handlebar or Brake/Clutch Reservoir with Two 1" Balls The RAM combination handlebar and brake/clutch reservoir base provides the ultimate flexibility for mounting. Mount to either your handlebar or brake/clutch, almost infinite adjustment and perfect viewing angles are providing in this kit. Hardware: Standard or metric thread stainless steel bolts, provided in the kit. The zinc coated metal u-bolt accommodates rails in diameter from 0.75" to 1.25" in diameter. Material: Powder Coated Marine Grade Aluminum Ball Size: 1" Rubber Ball "B" Size Note: The "U" in the part number reflects product packaged in poly bag.