RAM Flat Surface Mount for the Garmin Astro 320, GPSMAP 62, 62s, 62sc, 62st & 62stc Description: The RAM-B-138-GA41U consists of a 2.5" diameter round base with the universal AMPS hole pattern, double socket arm, diamond adapter base and high strength composite cradle. The mount is designed with a RAM 1" diameter patented rubber ball and socket system that has adjustment points at both ends of the double socket arm; this allowing for almost infinite adjustment and perfect viewing angles. Compatible Devices: Garmin Astro 320 Garmin GPSMAP 62 Garmin GPSMAP 62s Garmin GPSMAP 62sc Garmin GPSMAP 62st Garmin GPSMAP 62stc Material: High Strength Composite and Powder Coated Marine Grade Aluminum Ball Size: 1" Rubber Ball "B" Size

RAM Composite Twist Lock Suction Cup Mount for the Garmin Astro 320, GPSMAP 62, 62s, 62sc, 62st & 62stc The RAP-B-166-2-GA41U consists of a double socket arm, suction cup twist lock base, diamond adapter base and custom high strength composite cradle for the Garmin GPSMAP 62 series. The suction cup, twist lock base is designed to have a strong hold on glass and non-porous plastic surfaces, including RAM adhesive disks. Designed into the mount is a 1" diameter patented rubber ball and socket system with adjustment points at the base and cradle. With a twist of the arm knob, you can move the suction cup GPSMAP mount to your optimum viewing position. This mount is designed to hold the following devices: Garmin Astro 320 Garmin GPSMAP 62 Garmin GPSMAP 62s Garmin GPSMAP 62sc Garmin GPSMAP 62st Garmin GPSMAP 62stc Material: High Strength Composite Ball Size: 1" Rubber Ball "B" Size

RAM Handlebar Rail Mount with Zinc Coated U-Bolt Base for the Garmin Astro 320, GPSMAP 62, 62s, 62sc, 62st & 62stc The RAM-B-149Z-GA41 consists of a double socket arm, zinc coated u-bolt base, diamond adapter base and custom high strength composite cradle for the Garmin GPSMAP 62 series. Designed into the mount is a 1" diameter patented rubber ball and socket system with adjustment points at the base and cradle. With a twist of the arm knob, you can move the motorcycle GPSMAP mount to your optimum viewing position. Included in this package is hardware that will accommodate rails from 0.50" to 1.25" in diameter. This mount is designed to hold the following devices: Garmin Astro 320 Garmin GPSMAP 62 Garmin GPSMAP 62s Garmin GPSMAP 62sc Garmin GPSMAP 62st Garmin GPSMAP 62stc U-Bolt Dimensions: 0.50" to 1.25" Material: High Strength Composite and Powder Coated Marine Grade Aluminum Ball Size: 1" Rubber Ball "B" Size

RAM ATV/UTV Strap Mount for the Garmin Astro 320, GPSMAP 62, 62s, 62sc, 62st & 62stc Description: The RAM-B-149Z-2-GA41U consists of a steel strap base, u-bolt bases, double socket, diamond adapter base and high strength composite cradle. Designed for a clean installation, the RAM strap mount will accommodate most common roll bar sizes on UTV's, allowing for the placement of the RAM rubber ball base. This mount can also be attached to smaller diameter handlebars on ATVs using the included hardware. With the ball base in place, you have the foundation for mounting everything from GPS Devices, RAM Aqua Boxes, Spotlights and Radios. The mount is designed with a RAM 1" diameter patented rubber ball and socket system that has adjustment points at both ends of the double socket arm; this allowing for almost infinite adjustment and perfect viewing angles. Rail Accommodation Dimensions: Mount with Strap: 1.57" to a maximum of 3.15" Mount with U-Bolt: 0.50" to a maximum of 1.25" Compatible Devices: Garmin Astro 320 Garmin GPSMAP 62 Garmin GPSMAP 62s Garmin GPSMAP 62sc Garmin GPSMAP 62st Garmin GPSMAP 62stc Material: High Strength Composite

RAM EZ-ON/OFF™ Bicycle Mount for the Garmin Astro 320, GPSMAP 62, 62s, 62sc, 62st & 62stc Mount your Garmin GPSMAP quickly and easily with a RAM EZ-ON/OFF handlebar base. Designed to fit most common handlebar sizes, this compact and durable mount is ideally suited to the open road or trails. Uses common zip ties to attach to a variety of handlebar diameters. Made of high strength composite, it is light weight too. Adjustable to allow for the best viewing angle, this product is perfect for any cyclist and their compact electronic device. Mount includes 12 degree tappered shaft for tapered handlebars. This mount is designed to hold the following devices: Garmin Astro 320 Garmin GPSMAP 62 Garmin GPSMAP 62s Garmin GSPAMP 62sc Garmin GPSMAP 62st Garmin GPSMAP 62STC Material: High Strength Composite

This RAM high strength composite cradle is designed to hold the following devices: Garmin Astro 320 Garmin GPSMAP 62 Garmin GPSMAP 62s Garmin GPSMAP 62sc Garmin GPSMAP 62st Garmin GPSMAP 62stc Material: High Strength Composite

RAM® Form-Fit Cradle for Garmin GPSMAP® 176, 196, 276C, 396, 496 & More The RAM-HOL-GA7U consists of a high-strength composite cradle and hole pattern that will allow attachment to all RAM components or mounts that contain the universal AMP hole pattern. Compatible and interchangeable with a wide range of popular RAM mounting products, this cradle is ready to complement a GPS and become the most useful accessory in a vehicle.  Features: A set of two nuts and bolts to connect the cradle to any RAM components or mounts that contain the universal AMP hole pattern Specifications: Hardware Included: (2) #8-32 x 1/2" Machine Screws, (2) #8-32 x 5/8" Machine Screws, (2) #8-32 x 3/4" Machine Screws, and (2) #8-32 Nylock Nuts Hole Pattern (inch): 2-Hole AMPS: 1.912" Materials: High-strength composite Packaging Type: Polybag Weight: 0.14 lb. Compatibility: Garmin: GPSMAP 176, GPSMAP 176C, GPSMAP 196, GPSMAP 276C, GPSMAP 296, GPSMAP 376C, GPSMAP 378, GPSMAP 396, GPSMAP 478, and GPSMAP 496

RAM Flat Surface Mount w/Cradle for Garmin dēzl GPS RAM Cradle Holder for the Garmin dēzl 560LMT & 560LT: This RAM high strength composite cradle is designed to hold the following devices: Garmin dēzl 560LMT Garmin dēzl 560LT Features: Open access to all electronic ports including audio port, speaker/mic and mini USB Patent pending roller design for super smooth placement and removal of the GPS Custom pocket for factory dock Material: High Strength Composite Note: The "U" in the part number reflects product packaged in poly bag. The cradle includes a set of two nuts and bolts to connect the cradle to any of the RAM compatible mounts. RAM cradles do not include the RAM-B-238U (Diamond Base & Ball) or RAP-B-238U (Diamond Composite Base & Ball), required to attach to the cradle and RAM mounting system. Surface Mount: Simply choose your preferred mounting location and the possibilities become endless with the RAM-B-138U. Rubber ball and socket technology allows for almost infinite adjustment and perfect viewing angles. High quality materials insure your device is safe, secure, and within easy reach. RAM's design also dampens shock and vibration helping to extend the life of your device. Material: Powder Coated Marine Grade Aluminum

RMX4800-20 RailMount Pre-Cut f/Garmin GPSMAP® 7408 / 7408xsv / 7608 / 7608sxv RailMount NavPods are best used for mounting of an autopilot control, sailing instrument, or small chartplotter onto an existing pedestal guard. Fits onto any 1" or 1.25" diameter tube. A Chromed Stainless Steel arm is used to mount a NavPod. The NavPod can rotate 180 degrees for easy viewing while sitting under the dodger on a rainy day. All wire run from the NavPod, down the center of the stainless steel arm, and into the pedestal guard. This application provides a clean and sturdy installation for electronics, without replacement of the pedestal guard. All RailMount NavPods Include: Acrylic capped ABS plastic Chromed stainless steel tamper-proof fasteners Double Seal for watertight integrity Models are available pre-cut for popular electronics. Chromed stainless steel arm with swivel mount Two sets of adaptors included for 1" or 1.25" diameter tubing The Hi-Gloss Material NavPods are manufactured with a custom co-extruded acrylic capped ABS material. We use the absolute best UV resistant material that provides a very high gloss white finish that matches gel-coated fiberglass. The Gen3 enhancements now include a thicker gauge material that improves strength and 1provides for better structural rigidity. The Waterproof Seal All NavPods are manufactured with a double gasket system providing an excellent watertight seal between the front and back of the NavPod for protection of your Marine Electronics. NavPods are made to withstand the harshest of wet offshore boating conditions. Gen3 enhancements include a thicker external silicone gasket with improved flush fit. The internal EPDM gasket is now 50% thicker and is not subject to "compression set" like many rubber compounds. This is important when you need to open the NavPod in the future to service your electronics. The Nickel Chrome Plated Screws We use all stainless steel mounting hardware that is supplied with each NavPod. Large round head tamperproof screws have deeper sockets for the NavPod wrench for better holding ability when tightening than the previous screws. For Gen3 we provide nickel chrome-plated stainless steel tamperproof screws for security combined with a little bling! The Manufacturing Process Heavy-gauge thermoforming is considered an art since many processes come into play. It all starts with the design and development of the tooling. We are fortunate to have experienced in-house design engineers who utilize CAD programs like Solidworks, Catia and AutoCad. Surfcam is used to interface with our CNC machining centers to produce quality tools with precision tolerances. We have re-designed and re-tooled all of the popular NavPods. We have reviewed all of the former products and selected the best design elements of each and incorporated them in every new Gen3 product. Our Commitment to Quality We are committed to producing the best possible waterproof housing for Marine Electronics. Now with two decades of experience under our belt, we are confident you will have years of trouble free service and a long lasting high gloss finish. We will stand behind our commitment by now offering a 10-year warranty on all new Gen3 NavPods.

RailMount Pre-Cut for Garmin GPSMAP 8410xsv & 8610xsv (Fits 1″ or 1.25″ Tubing) *For Mounting on Starboard side of Pedestal Guard only  RailMount NavPods are best used for mounting of an autopilot control, sailing instrument, or small chartplotter onto an existing pedestal guard. Fits onto any 1” or 1.25” diameter tube. A Stainless Steel arm is used to mount the NavPod housing. The NavPod can rotate 180 degrees for easy viewing while sitting under the dodger on a rainy day. All wiring runs from the NavPod, down the center of the stainless steel arm, and into the pedestal guard. This application provides a clean and sturdy installation for electronics, without replacement of the pedestal guard. RailMounts are designed for all popular standard size instruments as well as 7 and 9 inch chartplotters. Structural Rigidity – The Gen3 enhancements now include a thicker gauge acrylic capped ABS material that improves strength and provides better structural rigidity. This thicker material allows for a larger waterproof seal. The better the structural rigidity, the less flexing when tightening and more uniform pressure on the seal. The excellent UV stability of the acrylic is combined with the durability of the ABS. The acrylic cap protects the ABS from UV and its potentially damaging effects on plastic. Waterproof Seal – All RailMount NavPods are manufactured with a double gasket system providing an excellent watertight seal. This seal provides the best protection of your Marine Electronics. NavPods are made to withstand the harshest wet offshore boating conditions. Gen3 enhancements include a thicker external silicone gasket with improved flush fit. The internal Poron Microcell Polyurethane gasket is now 50% thicker and is not subject to “compression set” like many rubber compounds. This is important when you need to open the NavPod in the future in order to service your electronics. The gasket will continue to do its job. Nickel Chrome-Plated Stainless Steel – We use all 316 stainless steel hardware that is supplied with each NavPod. Large round-head tamper-resistant screws have deeper sockets for the NavPod wrench for better holding ability when tightening than screws used on our Traditional Series NavPod. The Nickel Chrome-Plated Stainless Steel tamper-resistant screws provide security combined with a little style! Commitment to Quality – We stand behind our commitment by offering a 10-year warranty on all new Gen3 NavPods.

RailMount Pre-Cut for Garmin GPSMAP® 723, 723xsv, 743 & 743xsv RailMount NavPods are best used for mounting an autopilot control, sailing instrument, or small chartplotter onto an existing pedestal guard. Fits onto any 1″, 1.125″, or 1.25″ diameter tube. A Stainless Steel arm is used to mount the NavPod housing. The NavPod can rotate 180 degrees for easy viewing while sitting under the dodger on a rainy day. All wiring runs from the NavPod, down the center of the stainless steel arm (available space is 0.75″ inside the narrowest part of the arm, so keep this in mind for planning your cable run; most transducer cables will not fit through the arm), and into the pedestal guard. This application provides a clean and sturdy installation for electronics, without the replacement of the pedestal guard. RailMounts are designed for all popular standard-size instruments, as well as 7 and 9-inch chartplotters. Structural Rigidity – The Gen3 enhancements now include a thicker gauge acrylic capped ABS material that improves strength and provides better structural rigidity. This thicker material allows for a larger waterproof seal. The better the structural rigidity, the less flexing when tightening and more uniform pressure on the seal. The excellent UV stability of the acrylic is combined with the durability of the ABS. The acrylic cap protects the ABS from UV and its potentially damaging effects on plastic. Waterproof Seal – All RailMount NavPods are manufactured with a double gasket system providing an excellent watertight seal. This seal provides the best protection for your Marine Electronics. NavPods are made to withstand the harshest wet offshore boating conditions. Gen3 enhancements include a thicker external silicone gasket with an improved flush fit. The internal Poron Microcell Polyurethane gasket is now 50% thicker and is not subject to a “compression set” like many rubber compounds. This is important when you need to open the NavPod in the future in order to service your electronics. The gasket will continue to do its job. Nickel Chrome-Plated Stainless Steel – We use all 316 stainless steel hardware that is supplied with each NavPod. Large round-head tamper-resistant screws have deeper sockets for the NavPod wrench for better holding ability when tightening than screws used on our Traditional Series NavPod. The Nickel Chrome-Plated Stainless Steel tamper-resistant screws provide security combined with a little style! Commitment to Quality – We stand behind our commitment by offering a 10-year warranty on all new Gen3 NavPods.  

RailMount Pre-Cut for Garmin GPSMAP® 923 & 943xsv RailMount NavPods are best used for mounting an autopilot control, sailing instrument, or small chartplotter onto an existing pedestal guard. Fits onto any 1″, 1.125″, or 1.25″ diameter tube. A Stainless Steel arm is used to mount the NavPod housing. The NavPod can rotate 180 degrees for easy viewing while sitting under the dodger on a rainy day. All wiring runs from the NavPod, down the center of the stainless steel arm (available space is 0.75″ inside the narrowest part of the arm, so keep this in mind for planning your cable run; most transducer cables will not fit through the arm), and into the pedestal guard. This application provides a clean and sturdy installation for electronics, without the replacement of the pedestal guard. RailMounts are designed for all popular standard-size instruments, as well as 7 and 9-inch chartplotters. Structural Rigidity – The Gen3 enhancements now include a thicker gauge acrylic capped ABS material that improves strength and provides better structural rigidity. This thicker material allows for a larger waterproof seal. The better the structural rigidity, the less flexing when tightening and more uniform pressure on the seal. The excellent UV stability of the acrylic is combined with the durability of the ABS. The acrylic cap protects the ABS from UV and its potentially damaging effects on plastic. Waterproof Seal – All RailMount NavPods are manufactured with a double gasket system providing an excellent watertight seal. This seal provides the best protection for your Marine Electronics. NavPods are made to withstand the harshest wet offshore boating conditions. Gen3 enhancements include a thicker external silicone gasket with an improved flush fit. The internal Poron Microcell Polyurethane gasket is now 50% thicker and is not subject to a “compression set” like many rubber compounds. This is important when you need to open the NavPod in the future in order to service your electronics. The gasket will continue to do its job. Nickel Chrome-Plated Stainless Steel – We use all 316 stainless steel hardware that is supplied with each NavPod. Large round-head tamper-resistant screws have deeper sockets for the NavPod wrench for better holding ability when tightening than screws used on our Traditional Series NavPod. The Nickel Chrome-Plated Stainless Steel tamper-resistant screws provide security combined with a little style! Commitment to Quality – We stand behind our commitment by offering a 10-year warranty on all new Gen3 NavPods.

RMX4800-14 RailMount Pre-Cut for Garmin GPSMAP® 923, 923xsv, 943 & 943xsv RailMount NavPods are best used for mounting of an autopilot control, sailing instrument, or small chartplotter onto an existing pedestal guard. Fits onto any 1″, 1.125″, or 1.25″ diameter tube. A Stainless Steel arm is used to mount the NavPod housing. The NavPod can rotate 180 degrees for easy viewing while sitting under the dodger on a rainy day. All wiring runs from the NavPod, down the center of the stainless steel arm (available space is 0.75″ inside the narrowest part of the arm, so keep this in mind for planning your cable run; most transducer cables will not fit through the arm), and into the pedestal guard. This application provides a clean and sturdy installation for electronics, without the replacement of the pedestal guard. RailMounts are designed for all popular standard-size instruments, as well as 7 and 9-inch chartplotters. Structural Rigidity – The Gen3 enhancements now include a thicker gauge acrylic capped ABS material that improves strength and provides better structural rigidity. This thicker material allows for a larger waterproof seal. The better the structural rigidity, the less flexing when tightening and the more uniform pressure on the seal. The excellent UV stability of the acrylic is combined with the durability of the ABS. The acrylic cap protects the ABS from UV and its potentially damaging effects on plastic. Waterproof Seal – All RailMount NavPods are manufactured with a double gasket system providing an excellent watertight seal. This seal provides the best protection for your Marine Electronics. NavPods are made to withstand the harshest wet offshore boating conditions. Gen3 enhancements include a thicker external silicone gasket with an improved flush fit. The internal Poron Microcell Polyurethane gasket is now 50% thicker and is not subject to a “compression set” like many rubber compounds. This is important when you need to open the NavPod in the future in order to service your electronics. The gasket will continue to do its job. Nickel Chrome-Plated Stainless Steel – We use all 316 stainless steel hardware that is supplied with each NavPod. Large round-head tamper-resistant screws have deeper sockets for the NavPod wrench for better holding ability when tightening than screws used on our Traditional Series NavPod. The Nickel Chrome-Plated Stainless Steel tamper-resistant screws provide security combined with a little style! Commitment to Quality – We stand behind our commitment by offering a 10-year warranty on all new Gen3 NavPods.

RMX4500-01 RailMount Pre-Cut for Garmin echoMAP™ 7" Series Garmin echoMAP™ Models: 72SV 73SV 74SV 75SV 72DV 73DV 74DV 75DV RailMount NavPods are best used for mounting of an autopilot control, sailing instrument, or small chartplotter onto an existing pedestal guard. Fits onto any 1" or 1.25" diameter tube. A Chromed Stainless Steel arm is used to mount a NavPod. The NavPod can rotate 180 degrees for easy viewing while sitting under the dodger on a rainy day. All wire run from the NavPod, down the center of the stainless steel arm, and into the pedestal guard. This application provides a clean and sturdy installation for electronics, without replacement of the pedestal guard. The Hi-Gloss Material NavPods are manufactured with a custom co-extruded acrylic capped ABS material. We use the absolute best UV resistant material that provides a very high gloss white finish that matches gel-coated fiberglass. The Gen3 enhancements now include a thicker gauge material that improves strength and provides for better structural rigidity. The Waterproof Seal All NavPods are manufactured with a double gasket system providing an excellent watertight seal between the front and back of the NavPod for protection of your Marine Electronics. NavPods are made to withstand the harshest of wet offshore boating conditions. Gen3 enhancements include a thicker external silicone gasket with improved flush fit. The internal EPDM gasket is now 50% thicker and is not subject to "compression set" like many rubber compounds. This is important when you need to open the NavPod in the future to service your electronics. The Nickel Chrome Plated Screws We use all stainless steel mounting hardware that is supplied with each NavPod. Large round head tamperproof screws have deeper sockets for the NavPod wrench for better holding ability when tightening than the previous screws. For Gen3 we provide nickel chrome-plated stainless steel tamperproof screws for security combined with a little bling! The Manufacturing Process Heavy-gauge thermoforming is considered an art since many processes come into play. It all starts with the design and development of the tooling. We are fortunate to have experienced in-house design engineers who utilize CAD programs like Solidworks, Catia and AutoCad. Surfcam is used to interface with our CNC machining centers to produce quality tools with precision tolerances. Our Commitment to Quality We are committed to producing the best possible waterproof housing for Marine Electronics. Now with two decades of experience under our belt, we are confident you will have years of trouble free service and a long lasting high gloss finish. We will stand behind our commitment by now offering a 10-year warranty on all new Gen3 NavPods.

Ram Mounts Looking for all the Ram Mount products we carry them. You can find them all right here in our Ram Mount Store Aqua Box Mount section. With everything from camera mounts to vehicle mounts including cell phone mounts, you will have plenty of choices to consider and options to choose from. Ram Mounting Systems is a quality manufacturer of all kinds of different mounts for your watercraft. You can get cell phone mounts and drink cup mounts here, along with GPS mounts and fishing rod holders. There are even iPad/iPhone/iPod mounts so you do not have to worry about having your electronics safe but close at hand.   If you have a kayak we have kayak mounts, too, and you can even do some work or surf the internet with laptop mounts to choose from. Of course, you want to make sure you choose a good marine electronics mount for your equipment, so you do not risk losing anything vital. Tablet mounts, swing arm mounts, surface mounts, and suction cup mounts are all available, and we have seat mounts, as well. You can even choose from motorcycle mounts, and rail/handle bar mounts to ensure you have everything you need your all of your future adventures.