Vehicle Base Compatible Vehicles: DODGE RAM 1500-5500 (2008-2011) This No-Drill™ Laptop Stand System installs quickly and easily into the specified vehicles using the existing hardware of the passenger side seat rails. This configuration provides a telescoping feature that ranges from 12 to 18 inches. Dual swing arms provide articulation and 12 inches of reach for passenger and driver access to the mounted device. Patented rubber ball and socket joint provides additional adjustment as well as shock and vibration isolation Placement of Mount: Passenger side, front, where seat rail frame attaches to floor board. DRILLING REQUIREMENTS: No - attaches to seat studs Seat Configuration: Bucket Pole: Purchased Separately Weight: 2.1 lbs. Material: Powder Coated Steel Dimensions: A = 14.75", B = 3.8", C = 1.75", Hole Center = 13.25" Features: Quick installation with no drilling needed. Rock solid construction with lifetime warranty. Low profile keeps mount away from passenger leg space. Won?t interfere with levers or factory-installed console or 4WD lever. Designed to accommodate trucks with PTO Swing Arm The RAM RAM-VP-SW1-89, combination swing arm/tele-pole system, will connect to any RAM vehicle base without a welded female tele-pole. Included is a tele-pole with a height range from 11.5" to 17"; it can be easily adjusted by turning the knob at the top of the post. Once the knob has been tightened, the tele-pole becomes a rigid support for any RAM cradle, holder or Tough-Tray. The double swing arm with rotating plate, allows you to twist and tilt the viewing angle of your laptop, tablet, UMPC, monitor, or any other connected electronic device, when mounted on your RAM Vehicle Mount. Taking the highly successful RAM Vehicle Mounts to the next level, this rotating swivel arm gives you even more viewing positions for your mounted electronic device while holding everything firmly in place. The length of the double swing arm is 12". Material: Powder Coated Marine Grade Aluminum Ball Size: 1.5" Rubber Ball "C" Size Note: Part number reflects product packaged in clear clam shell for store shelf display. Laptop Mount Tray The RAM Tough-Tray is spring loaded expandable tray that can accommodate 10 to 16 inch wide laptops. The tray includes four (4) side clamping arm with rubber grip feature. These arms can be moved both vertically and horizontally. This allows for a custom fit for varying thicknesses of laptops and the freedom of not blocking ports or drives. Hole patterns on perimeter of tray facilitate the mounting of additional RAM systems to support GPS, PDAs or other electronics. Tough-Tray Dimensions: Tray Depth: 10.0" Tray Thickness: 2.125" Tray Width (Expansion): 10" to 16" Side Clamp Arm Height: 0.5" (min) to 1.75" (max) Material: High Strength Composite Note: Part number reflects product packaged in clear clam shell for store shelf display. The Tough-Tray is compatible with laptops that have 17" screens. If the Tough-Tray Laptop Cradle is intended to hold a laptop or device while the vehicle is in motion, we recommend the Secure-n-Motion kit.

Vehicle Base Compatible Vehicles: DODGE RAM 1500-5500 (2008-2013) RAM 1500-5500 (2014) Placement of Mount: Passenger side, front, where seat rail frame attaches to floor board. DRILLING REQUIREMENTS: No - attaches to seat studs Seat Configuration: Bucket Pole: Purchased Separately Weight: 2.1 lbs. Material: Powder Coated Steel Dimensions: A = 14.75", B = 3.8", C = 1.75", Hole Center = 13.25" Features: Quick installation with no drilling needed. Rock solid construction with lifetime warranty. Low profile keeps mount away from passenger leg space. Won't interfere with levers or factory-installed console or 4WD lever. Designed to accommodate trucks with PTO

RAM POD I Universal No-Drill Vehicle Mount with 18" Flex Rod & Diamond Adapter Base Part #: RAM-B-316-1-238U The RAM POD I, No-Drill vehicle mount, consists of a 1" ball and diamond base with 18" rigid flex rod. The flex rod base is designed to connect to a vehicle seat rail bolt in cars, trucks, fleet vehicles and suvs. The flex rod can hold light to medium weight items in your vehicle safely and securely. Material: High Strength Composite and Powder Coated Marine Grade Aluminum Ball Size: 1" Rubber Ball "B" Size Note: The "U" in the part number reflects product packaged in poly bag.

RAM POD I Universal No-Drill Vehicle Mount Connecting to No Ball Base Part #: RAM-B-316-1U The RAM-B-316-1U, universal RAM-POD I vehicle mount, consists of a single open socket arm, connected to a 18" long flexible rod. This RAM POD I allows you to mount a light to medium weight item in a car safely and securely. Installation Instructions: At right angles to the base of the flexible 18" long leg is a foot with a mounting hole. Simply place the hole into the passenger seat mounting bolt and adjust the mount to the required height with the flexible leg. The rigid flexible arm will hold everything you need safely and securely. Material: Powder Coated Marine Grade Aluminum Ball Size: 1" Rubber Ball "B" Size Note: The "U" in the part number reflects product packaged in poly bag.

POD I Universal No-Drill™ Vehicle Mount with 24" Rigid Aluminum Rod & 1.5" Diameter Ball Round Adapter Base The RAM POD I, universal no-drill™, vehicle mount is the latest in the Mobile In-Car range from RAM. This RAM POD I allows you to mount a light to medium weight item in a car safely and securely. Features: Installation Instructions: At right angles to the base of the flexible 24" long leg is a foot with a mounting hole. Simply place the hole into the passenger seat mounting bolt and adjust the mount to the required height with the flexible leg. The rigid flexible arm will hold everything you need safely and securely. Material: Powder Coated Marine Grade Aluminum Ball Size: 1.5" Rubber Ball Size Note: The "U" in the part number reflects product packaged in poly bag

No-Drill™ Laptop Mount w/ Adjust-A-Pole™ f/ The Dodge RAM 1500-5500 This No-Drill™ Laptop Stand System installs quickly and easily into the specified vehicles using the existing hardware of the passenger side seat rails. This configuration provides a telescoping feature that ranges from 12 to 18 inches. Dual swing arms provide articulation and 12 inches of reach for passenger and driver access to the mounted device. Patented rubber ball and socket joint provides additional adjustment as well as shock and vibration isolation. The RAM Tough Tray™ is spring loaded to accommodate 10" to 16" wide laptops & (17" wide screens). The tray features four adjustable retaining arms with rubber grip feature. These arms can be moved both vertically and horizontally. This allows for a custom fit for varying thicknesses of laptops and the freedom of not blocking ports or drives. A screen support and USB light are also available to accessorize the tray. Hole patterns on perimeter of tray facilitate the mounting of additional RAM systems to support GPS or other electronics. Compatible Vehicles: RAM 1500 (2012-2018) RAM 1500 Classic (2019-2021) RAM 2500-5500 (2012-2021) Placement of Mount: Passenger side, front, where seat rail frame attaches to floor board. Drilling Requirements: No - attaches to seat studs Seat Configuration: Bucket Material: High Strength Composite and Powder Coated Steel Notes: Low profile design limits intrusion on passenger side leg space. Base will not interfere with levers or factory installed console or 4WD lever. Base designed to accommodate trucks with power take-off (PTO.) If the Tough-Tray™ Laptop Cradle is intended to hold a laptop or device while the vehicle is in motion, we recommend the Secure-N-Motion™ kit.

RAM Universal No-Drill RAM POD III Vehicle Mount with Double Socket Arm & 2/2.5" Round Bases (AMPs Hole Pattern) The RAM-316-3-202U consists of the RAM POD III No-Drill vehicle base, three rigid aluminum rod legs, double socket arm and two 2.5" round bases that contain the universal AMPs hole pattern. The base of the mount connects to your seat rail without any drilling necessary. The rigid aluminum rod legs can be bent to position your device to its optimum viewing location. The mount is designed with a RAM 1.5" diameter patented rubber ball and socket system that has adjustment points at both ends of the double socket arm; this allowing for almost infinite adjustment and perfect viewing angles. The universal AMPs hole pattern found on the round base adapter will connect to many RAM cradles. Leg Lengths: 18", 20" and 30" Installation Instructions: At right angles to the base of two legs are feet with mounting holes. Simply place the holes into the passenger seat mounting bolts and adjust the mount to the required height with the rigid aluminum rod legs. The third leg on the RAM POD III should also be adjusted to help support the mount. The rigid aluminum rod arms will hold everything you need safely and securely. Material: Powder Coated Marine Grade Aluminum Ball Size: 1.5" Rubber Ball Size Note: The "U" in the part number reflects product packaged in poly bag.

RAM Universal No-Drill RAM POD III Vehicle Mount with Double Socket Arm, 2.5" Round Base (AMPs Hole Pattern) & 3.625" Square Base (VESA 75mm X 75mm Hole Pattern) The RAM-316-3-2461U consists of the RAM POD III No-Drill vehicle base, 3 rigid aluminum rod legs, double socket arm, 2.5" round base that contain the universal AMPs hole pattern and 3.625" square base that contains the VESA hole pattern. The base of the mount connects to your seat rail without any drilling necessary. The rigid aluminum rod legs can be bent to position your device to its optimum viewing location. The mount is designed with a RAM 1.5" diameter patented rubber ball and socket system that has adjustment points at both ends of the double socket arm; this allowing for almost infinite adjustment and perfect viewing angles. The square base includes a 75mm X 75mm VESA hole pattern with 1.5" rubber ball positioned 0.88" from the center of one edge. Leg Lengths: 18", 20" and 30" Installation Instructions: At right angles to the base of two legs are feet with mounting holes. Simply place the holes into the passenger seat mounting bolts and adjust the mount to the required height with the rigid aluminum rod legs. The third leg on the RAM POD III should also be adjusted to help support the mount. The rigid aluminum rod arms will hold everything you need safely and securely. Material: Powder Coated Marine Grade Aluminum Ball Size: 1.5" Rubber Ball Size Note: The "U" in the part number reflects product packaged in poly bag.

RAM POD III Universal No-Drill Laptop Mount w/Tough-Tray The RAM-316-3SW1U consists of the RAM POD III No-Drill vehicle base, three rigid aluminum rod legs, ratchet swing arm and RAM Tough-Tray. The base of the mount connects to your seat rail without any drilling necessary. The rigid aluminum rod legs can be bent to position your device to its optimum viewing location. The mount is designed with a RAM 1.5" diameter patented rubber ball and socket system that has adjustment points at both ends of the double socket arm; this allowing for almost infinite adjustment and perfect viewing angles. The RAM Tough-Tray is spring loaded expandable tray that can accommodate 10 to 16 inch wide laptops. The tray includes four (4) side clamping arm with rubber grip feature. These arms can be moved both vertically and horizontally. This allows for a custom fit for varying thicknesses of laptops and the freedom of not blocking ports or drives. Hole patterns on perimeter of tray facilitate the mounting of additional RAM systems to support GPS, smartphones or other electronics. Leg Lengths: 18", 20" and 30" Installation Instructions: At right angles to the base of two legs are feet with mounting holes. Simply place the holes into the passenger seat mounting bolts and adjust the mount to the required height with the rigid aluminum rod legs. The third leg on the RAM POD III should also be adjusted to help support the mount. The rigid aluminum rod arms will hold everything you need safely and securely. Material: Powder Coated Marine Grade Aluminum Ball Size: 1.5" Rubber Ball Size Note: The "U" in the part number reflects product packaged in poly bag.

No-Drill™ Laptop Base f/ The Dodge RAM 1500-5500 - 2008-2015 Specifications/Features Compatible Vehicles: Dodge RAM 1500-5500 (2008-2015) Placement of Mount: Passenger side, front, where seat rail frame attaches to floor board. Drilling Requirements: No - attaches to seat studs Seat Configuration: Bucket Pole: Purchased Separately Weight: 2.1 lbs. Material: Powder Coated Steel Features: Quick installation with no drilling needed. Rock solid construction with lifetime warranty. Low profile keeps mount away from passenger leg space. Won't interfere with levers or factory-installed console or 4WD lever. Designed to accommodate trucks with PTO

No-Drill™ Vehicle Base for '07-13 Chevrolet Silverado + More The RAM® No-Drill™ laptop mounting base features a heavy-duty steel mounting base custom designed to fit this vehicle perfectly. Using the passenger side seat rail bolts as attachment points, existing hardware is used to secure the laptop mount base in the vehicle. Placement of Mount: Passenger side floor board, in front of seat Drilling Requirements: No - attaches to seat studs Seat Configuration: Bucket Hole Pattern: Seat Bolt Distance: 15"-15.5625" center to center Pole: Purchased Separately Material: Powder Coated Steel Features: Quick installation with no drilling needed. Rock solid construction with a lifetime warranty Compatible Vehicles Chevrolet Avalanche (2007-2013) Avalanche LS/LT/LTX (2009) Silverado (2007-2013) Silverado 1500 (2007-2013) Silverado 1500 Hybrid (2008) Silverado 1500HD (2008) Silverado 2500HD (2007-2013) Silverado 3500HD (2007-2013) Suburban (2007-2014) Suburban 12-Ton (2012) Suburban 34-Ton (2012) Tahoe (Front Bucket Seats Only) (2007-2014) GMC Sierra (2007-2013) Sierra 1500 (2007-2013) Sierra 1500 Denali (2012) Sierra 1500 Hybrid (2008 2012) Sierra 1500HD (2008) Sierra 2500HD (2007-2014) Sierra 2500HD Denali (2007-2012) Sierra 3500HD (2007-2014) Sierra 3500HD Denali (2007-2014) Sierra Hybrid (2011) Yukon (2007-2014) Hummer H2 (2003-2011)

RAM® No-Drill™ Vehicle Base for 2019 RAM 1500 This heavy duty, steel RAM® No-Drill™ laptop vehicle base is custom-designed for the 2019 Dodge RAM 1500. Using the passenger side seat rail bolts as attachment points, provided hardware is used to secure the mounting base in the vehicle. Specifications: Placement of Mount: Passenger side, front, where seat rail frame attaches to floor board Drilling Requirements: No - attaches to seat studs Seat Configuration: Bucket Pole: Purchased Separately Material: Powder Coated Steel

RAM Mount No Drill Vehichle System f/Nissan NV1500, NV2500HD, NV3500HD &  Toyota Tundra This No-Drill™ Laptop Stand System installs quickly and easily into the specified vehicles using the existing hardware of the passenger side seat rails. This configuration provides a telescoping feature that ranges from 12 to 18 inches. Dual swing arms provide articulation and 12 inches of reach for passenger and driver access to the mounted device. Patented rubber ball and socket joint provides additional adjustment as well as shock and vibration isolation. The RAM Tough Tray™ is spring loaded to accommodate 10" to 16" wide laptops & (17" wide screens) The tray features four adjustable retaining arms with rubber grip feature. These arms can be moved both vertically and horizontally. This allows for a custom fit for varying thicknesses of laptops and the freedom of not blocking ports or drives. A screen support and USB light are also available to accessorize the tray. Hole patterns on perimeter of tray facilitate the mounting of additional RAM systems to support GPS or other electronics. Compatible Vehicles: Nissan NV1500 (2011-2021) Nissan NV2500 HD (2011-2020) Nissan NV3500 HD (2011-2020) Toyota Tundra (2007-2021) Features: Placement of Mount: Passenger side, front, where seat rail frame attaches to floor board. Drilling Requirements: No - attaches to seat studs Seat Configuration: Bucket Material: High Strength Composite and Powder Coated Steel Notes: If the Tough-Tray™ Laptop Cradle is intended to hold a laptop or device while the vehicle is in motion, we recommend the Secure-N-Motion™ kit.

No-Drill™ Vehicle Base f/ '10-13 Ford Transit Connect + More Compatible Vehicles: Ford Transit Connect (2010-2013) Transit Connect Wagon Premiun (2013) Transit Connect XL Van (2013) Transit Connect XLT Van (2013) Transit Connect XLT Wagon (2013) Dodge Grand Caravan (2008-2009 2012-2016) Grand Caravan AVP (2013) Grand Caravan Crew (2013) Grand Caravan RT (2013) Grand Caravan SE (2013) Grand Caravan SXT (2013) RAM C/V Tradesman Van (2014-2015) Chrysler Town & Country (2008-2009 2012-2016) Placement of Mount: Passenger side, front, where seat rail frame attaches to floor board Drilling Requirements: No - attaches to seat studs Seat Configuration: Bucket Pole: Purchased Separately Weight: 4.5 lbs. Material: Powder Coated Steel

No Drill Vehicle Laptop Base for Nissan NV1500, NV2500 HD, NV3500 HD & Toyota Tundra The RAM® No-Drill™ laptop mounting base features a heavy-duty steel mounting base custom designed to fit this vehicle perfectly. Using the passenger side seat rail bolts as attachment points, existing hardware is used to secure the laptop mount base in the vehicle. Features: Installs in minutes with no drilling required Low profile keeps mount away from passenger leg space Adjustable riser included for pole adjustment Specifications: Placement of Mount: Passenger side, front, where seat rail frame attaches to floor board Drilling Requirements: No, attaches to seat studs Seat Configuration: Bucket Pole: Purchased Separately Material: Powder Coated Steel Features: Quick installtion with no drilling needed, rock solid construction with lifetime warranty Weight: 11.0 lbs Compatible Vehicles: Nissan NV1500 (2011-2015) Nissan NV2500 HD (2011-2015) Nissan NV3500 HD (2011-2015) Toyota Tundra (2007-2015)