Ram Mounts Looking for all the Ram Mount products we carry them. You can find them all right here in our Ram Mount Store Aqua Box Mount section. With everything from camera mounts to vehicle mounts including cell phone mounts, you will have plenty of choices to consider and options to choose from. Ram Mounting Systems is a quality manufacturer of all kinds of different mounts for your watercraft. You can get cell phone mounts and drink cup mounts here, along with GPS mounts and fishing rod holders. There are even iPad/iPhone/iPod mounts so you do not have to worry about having your electronics safe but close at hand.   If you have a kayak we have kayak mounts, too, and you can even do some work or surf the internet with laptop mounts to choose from. Of course, you want to make sure you choose a good marine electronics mount for your equipment, so you do not risk losing anything vital. Tablet mounts, swing arm mounts, surface mounts, and suction cup mounts are all available, and we have seat mounts, as well. You can even choose from motorcycle mounts, and rail/handle bar mounts to ensure you have everything you need your all of your future adventures.

RAM Flat Surface Horizontal Single Swing Arm Mount The RAM single swing arm mount consists of a 6" long BENT swing arm mounted on a horizontal surface mounting base. At the device mounting end of the mount is a rectangular 6.25" x 2" plate. There are two (2) pivoting points on the mount. One at the swing arm and base and one at the center of the rectangular plate and the end of the swing arm. Each pivoting point allows a complete 360 degree rotation. Dimensions: Center of knob to center of ball socket: 6" Overall length of swing arm assembly: 10.75" Overall height: 5.6" Height from base to top of knob: 4.91" Material: Powder Coated Marine Grade Aluminum Note:The "U" in the part number reflects product packaged in poly bag. The included plate is a universal mounting bracket with a selection of mounting hole locations. In certain applications additional holes may need to be drilled for proper fit with your electronic device.

RAM Yoke Clamp Mount w/Double Socket Arm & Diamond Base Adapter Part #: RAM-B-121-238U Consists of a double socket arm, universal diamond base and yoke clamp base. The hole pattern found on the diamond base will connect to many RAM cradles, as well as third party cradles including mounts with the industry standard AMPS hole pattern. The clamp base will accommodate rails in diameter from 0.625" to 1.25". The 1" rubber ball is at a right angle to the plane of the mount so when connected to a rail, the ball sits parallel to the rail. Material: Powder Coated Marine Grade Aluminum Ball Size: 1" Rubber Ball "B" Size Note: The "U" in the part number reflects product packaged in poly bag.

RAM 1.5" Diameter Ball Mount with 2/2.5" Round Bases - AMPs Hole Pattern The RAM-101U consists of a double socket arm and two 2.5" diameter round bases that contain the universal AMPS hole pattern. The mount is designed with a 1.5" diameter patented rubber ball and socket system that has adjustment points at both ends of the double socket arm; this allowing for almost infinite adjustment and perfect viewing angles. The hole pattern found on the round base adapter will connect to many RAM cradles, including all iPad cradles. The included RAM's patented design dampens shock and vibration, helping to extend the life of your device. Overall Height: 7.35" Material: Powder Coated Marine Grade Aluminum Ball Size: 1.5" Rubber Ball Size Note: The "U" in the part number reflects product packaged in poly bag. If you prefer a smaller double socket arm with two round bases, RAM recommends the RAM-B-101U.

RAM Mount 1.5 Inch Ball Double Socket Arm with 2.5 Inch Round Base The RAM Mount RAM-103U mount, with standard arm, consists of the 1.5" diameter ball and socket system with one open socket end. This mount is designed to be used with any of the RAM mounting bases or cradles with a 1.5" diameter rubber ball. The RAM-202U round base has a 1.5" diameter rubber ball connected at right angles to a 2.5" diameter base. The plate has pre-drilled holes in the base, including the universal AMPS hole pattern. Material: Powder Coated Marine Grade Aluminum Ball Size: 1.5" Rubber Ball Size Note: The "U" in the part number reflects product packaged in poly bag.

The RAM-D-201U-C, short double socket arm, has a socket at both ends that accommodates 2.25" ball bases. A single spring inside the arm opens the end sockets, allowing you to pivot the ball and socket connection. This socket technology allows for almost infinite adjustment and perfect viewing angles. Dimensions: Overall Length: 5.0625" Socket-To-Socket Length: 3.1875" Material: Powder Coated Marine Grade Aluminum Ball Size: 2.25" Rubber Ball "D" Size

Low Profile Composite Double Socket Arm The RAP-B-201U, composite standard double socket arm, has a socket at both ends that accommodates 1" ball bases. A single spring inside the arm opens the end sockets, allowing you to pivot the ball and socket connection. This socket technology allows for almost infinite adjustment and perfect viewing angles.  Features: Material: High Strength Composite Ball Size: B Size 1" Rubber Ball Note: The "U" in the part number reflects product packaged in poly bag Dimensions: Overall Length: 2.75" Socket-To-Socket Length: 2"

Description: The RAP-201U, standard double socket arm, has a socket at both ends that accommodates 1.5" ball bases. A single spring inside the arm opens the end sockets, allowing you to pivot the ball and socket connection. This socket technology allows for almost infinite adjustment and perfect viewing angles. Dimensions: Overall Length: 5.625" Socket-To-Socket Length: 4.5" Material: High Strength Composite Ball Size: 1.5" Rubber Ball Size

RAM Double Swing Arm with 8" Male Tele-Pole™, 9" Female Tele-Pole™ & 2.5" Round Base (AMPs Hole Pattern) Description The RAM RAM-VP-SW1-89, combination swing arm/tele-pole system, will connect to any RAM vehicle base without a welded female tele-pole. Included is a tele-pole with a height range from 11.5" to 17"; it can be easily adjusted by turning the knob at the top of the post. Once the knob has been tightened, the tele-pole becomes a rigid support for any RAM cradle, holder or Tough-Tray. The double swing arm with rotating plate, allows you to twist and tilt the viewing angle of your laptop, tablet, UMPC, monitor, or any other connected electronic device, when mounted on your RAM Vehicle Mount. Taking the highly successful RAM Vehicle Mounts to the next level, this rotating swivel arm gives you even more viewing positions for your mounted electronic device while holding everything firmly in place. The length of the double swing arm is 12". Material: Powder Coated Marine Grade Aluminum Ball Size: 1.5" Rubber Ball "C" Size Note: Part number reflects product packaged in clear clam shell for store shelf display.

RAM Double Swing Arm with 4" Male and No Female Tele-Pole The RAM-VP-SW1-4, combination swing arm/tele-pole system, will connect to any RAM vehicle base with a welded female tele-pole, as well as RAM Framed Tough-Box Consoles. Included is a 4" tele-pole that can be easily adjusted by turning the knob at the top of the post. Once the knob has been tightened, the tele-pole becomes a rigid support for any RAM cradle, holder or Tough-Tray. The double swing arm mount includes a base & ball with pre-drilled holes, including the universal AMPS hole pattern; this accommodating most keyboards. The length of the double swing arm is 12". Material: Powder Coated Marine Grade Aluminum Note: Part number reflects product packaged in clear clam shell for store shelf display.

RAM Double Swing Arm w/4" Male & No Female Tele-Pole Swing Arm connects to a 75mm x 75mm VESA Plate.

Double Ball Mount with 1/4"-20 Male Thread The RAM-B-101AU consists of a double socket arm, one 2.5" diameter round base with the universal AMPS hole pattern and universal camera/camcorder base. The universal camera/camcorder base consists of a 1" diameter rubber ball connected to a 2.5" diameter round base with 1/4-20 camera thread. The male thread matches most standard camera and camcorder female threads found on the bottom of the camera. Rubber ball, socket technology dampens shock and vibration, as well as allows for almost infinite adjustment, perfect viewing angles.  Specifications: Dimensions: Overall Height: 5" Material: Powder Coated Marine Grade Aluminum Ball Size: B Size 1" Rubber Ball Note: The "U" in the part number reflects product packaged in poly bag. Weight: 0.51 lbs.

RAM Handlebar Rail Mount with Zinc Coated U-Bolt Base, Short Double Socket Arm & Round Base Adapter that Contains a 1/4"-20 Thread for Cameras Part #: RAM-B-149ZA-C1U The RAM zinc coated u-bolt rail base consists of the 1" diameter ball and socket system with RAM Universal 1/4"-20 thread centered on a 2.5" diameter plate. This mount is designed to be a universal mounting solution for both still and moving cameras. The base has a 1.0" diameter rubber ball designed to sit at right angles to the mounting rail. The zinc coated metal u-bolt and nuts included will fit a circular rail with diameter from 0.5" to 1.25". To mount the rail base, place the top of the base on the rail and then slide the u-bolt around the rail, into the holes in the base top. Now tighten the screws onto the u-bolt until the base is clamped firmly. If you desire, you can now slot the black composite covers over the exposed ends of the u-bolt. Material: Powder Coated Marine Grade Aluminum Ball Size: 1" Rubber Ball "B" Size Note: The "U" in the part number reflects product packaged in poly bag. The male 1/4" long, 1/4"-20 thread in the middle of the 2.5" diameter plate will connect to the standard female thread found at the bottom of most still and video cameras.

2.5" Round Base with 3/8"-16 Female Threaded Hol & 1.5" Ball The RAM-202CNSU consists of a 1.5" diameter rubber ball connected to a flat 2.5" diameter base with 3/8"-16 female threaded hole. This mount has pre-drilled holes, including the universal AMPS hole pattern. Features: Material: Powder Coated Marine Grade Aluminum Ball Size: 1.5" Rubber Ball Size Note: Part number reflects product packaged in clear clam shell for store shelf display Weight: 0.23 lbs.

RAM 1.5" Ball with 1/4"-20 Male Threaded Post for Cameras The RAM-237U, universal camera and camcorder base, consists of a 1.5" diameter rubber ball, connected to a 1/4"-20 camera thread. The male thread matches most standard camera and camcorder female threads found on the bottom of the camera. Compatible Cameras: Contour GPS Contour HD GoPro HD Helmet HERO GoPro HD Motorsports HERO GoPro HD Surf HERO GoPro Helmet HERO Wide GoPro Motorsports HERO GoPro Motorsports HERO Wide GoPro RC HERO GoPro Surf Hero GoPro Wide HERO Material: Powder Coated Marine Grade Aluminum Ball Size: 1.5" Rubber Ball Size Note: The "U" in the part number reflects product packaged in poly bag.