March AC-5C-MD Reverse Osmosis Feed Pump 115 Volt Applications for the AC-5C-MD Magnetic Drive Pump include chemical recirculation, refrigerators, small scrubbers, detergent mixers, computer cooling, carbon arc furnace cooling, and marine air conditioners. March Pump's industrial AC-5C-MD is an American seal-less centrifugal magnetic drive pump ideal for applications such as chemical recirculation, chemical transfer, and scrubber systems. It is capable of generating a maximum flow of 17 gallons per minute at 1 feet, and its maximum head is 27 Feet (or around 11PSI). The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Buna N, Ceramic, and Ceramic Magnet. The inlet connection is 1 inch female pipe thread, and the outlet is 0.5 inch male pipe thread. The standard motor is a 1 Phase 115V or 230V 0.125 Horsepower fan cooled motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options). The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheit or 87 Celsius. The March AC-5C-MD centrifugal magnetic drive pump is capable of handling mildly or highly corrosive chemicals, acids, and solvents.   Max Flow 17 GPM 60 LPM Max Head 27 FT 6 M Power .125 HP .093 KW Electrical 115V 50/60HZ   Type Centrifugal Mag Drive Inlet 1"FPT Outlet 1/2"MPT Wet End Polypropylene (Front and Rear Housing, Impeller), Buna N (O-Ring), Ceramic (Shaft, Thrust Washers), Ceramic Magnet   Available with 750 Priming Chamber

March AC-5C-MD Reverse Osmosis Feed Pump 230V Applications for the AC-5C-MD Magnetic Drive Pump include chemical recirculation, refrigerators, small scrubbers, detergent mixers, computer cooling, carbon arc furnace cooling, and marine air conditioners. March Pump's industrial AC-5C-MD is an American seal-less centrifugal magnetic drive pump ideal for applications such as chemical recirculation, chemical transfer, and scrubber systems. It is capable of generating a maximum flow of 17 gallons per minute at 1 feet, and its maximum head is 27 Feet (or around 11PSI). The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Buna N, Ceramic, and Ceramic Magnet. The inlet connection is 1 inch female pipe thread, and the outlet is 0.5 inch male pipe thread. The standard motor is a 1 Phase 115V or 230V 0.125 Horsepower fan cooled motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheit. The March AC-5C-MD centrifugal magnetic drive pump is capable of handling mildly or highly corrosive chemicals, acids, and solvents.   Max Flow 17 GPM 60 LPM Max Head 27 FT 6 M Power .125 HP .093 KW Electrical 230V 50/60HZ   Type Centrifugal Mag Drive Inlet 1"FPT Outlet 1/2"MPT Wet End Polypropylene (Front and Rear Housing, Impeller), Buna N (O-Ring), Ceramic (Shaft, Thrust Washers), Ceramic Magnet  

March TE-5.5S-MD Mag Drive Pump 115 volts Applications for the March TE-5.5S-MD Magnetic Drive Pump include chemical recirculation, chemical transfer, refrigerators, scrubber systems, detergent mixers, computer cooling, carbon arc furnace cooling, silver recovery systems, and marine air conditioners. The March TE-5.5S-MD has pumped Acetic Acid, Citric Acid, Ethylene Glycol, Formaldehyde, Potassium Chloride, Potassium Hydroxide, Sodium Chloride, Sodium Hydroxide (Caustic Soda), Fresh Water, Salt Water, and many more chemicals.  The TE-5.5S-MD may have been modified to handle these chemicals.   March Pump's industrial TE-5.5S-MD is an American seal-less centrifugal magnetic drive pump ideal for applications such as chemical recirculation, chemical transfer, and scrubber systems. It is capable of generating a maximum flow of 30 gallons per minute at 11 feet, and its maximum head is 41 Feet (or around 18PSI). The standard wet end (the materials that come into contact with the solution) is composed of 316 Stainless Steel, Viton, Carbon, and Ceramic. The inlet connection is 1 inch female pipe thread, and the outlet is 0.75 inch male pipe thread. The standard motor is a 1 Phase 115/230V or 3 Phase 230/460V 0.33 Horsepower totally enclosed fan cooled motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options). The maximum internal pressure the pump can tolerate is 200PSI, and the maximum liquid temperature is 250 Fahrenheit or 121 Celsius. The March TE-5.5S-MD centrifugal magnetic drive pump is capable of handling mildly or highly corrosive chemicals, acids, and solvents.   Unit System 60Hz 50Hz Max Flow 30 GPM 102 LPM Max Head 41 FT 9 M Power .33 HP .248 KW Electrical 1PH 115/230V    3PH 230/460V 50/60HZ   Type Centrifugal Mag Drive Inlet 1"FPT Outlet 3/4"MPT Wet End 316 Stainless Steel (Front and Rear Housing, Impeller), Viton (O-Ring), Ceramic (Shaft, Thrust Washers), Carbon (Bushing)

Little Giant 3-MD-SC Magnetic Drive Pump 581503 Little Giant 3-MD-SC Magnetic Drive Pump. This Pump will handle up to a 48,000 BTU Air Conditioner Motor 115 Volt 50/60 Hz 1/12 HP Open Fan Cooled Motor, 750 GPH at 1 Foot Head, Shutoff Head 21.9 Feet, Inlet: 3/4" FNPT, Outlet: 1/2" MNPT, Polypropylene Body, Fluid Temperature Up to 150F (66C), UR/C-CSA Listed, 6 Foot Power Cord   581503 Magnetically driven pump for Circulation of moderately corrosive acids, alkalis, solvents, brine, plating solutions, sterile solutions, and other moderately corrosive chemicals and solutions that are compatible with the pump's material of construction

Little Giant 3-MD-SC Mag-Drive Pump 581513 Little Giant 3-MD-SC 230V Magnetic Drive Pump This Pump will handle up to a 48,000 BTU Air Conditioner Motor 230 Volt 60 Hz 1/12 HP Open Fan Cooled Motor, 750 GPH at 1 Foot Head, Shutoff Head 21.9 Feet, Inlet: 3/4" FNPT, Outlet: 1/2" MNPT, Polypropylene Body, Fluid Temperature Up to 150F (66C), UR/C-CSA Listed, 6 Foot Power Cord   581513 Magnetically driven pump for semi-corrosive chemicals and solutions. The MD-SC Series features leakproof, seal-less magnetic drives and are designed for in-line, non-submersed use

March TE-5C-MD Mag Drive Pump 115V Applications for the TE-5C-MD Magnetic Drive Pump include chemical recirculation, chemical transfer, refrigerators, small scrubbers, detergent mixers, computer cooling, carbon arc furnace cooling, and marine air conditioners. March Pump's industrial TE-5C-MD is an American seal-less centrifugal magnetic drive pump ideal for applications such as chemical recirculation, chemical transfer, and scrubber systems. It is capable of generating a maximum flow of 17 gallons per minute at 4 feet, and its maximum head is 29 Feet (or around 12PSI). The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Viton, and Ceramic. The inlet connection is 1 inch female pipe thread, and the outlet is 0.5 male pipe thread. The standard motor is a 1 Phase 115/230V 0.2 Horsepower totally enclosed fan cooled motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheit or 87 Celsius. The March TE-5C-MD centrifugal magnetic drive pump is capable of handling mildly or highly corrosive chemicals, acids, and solvents.   Unit System 60Hz 50Hz Max Flow 18 GPM 60.5 LPM Max Head 29 FT 6.3 M Power .2 HP .149 KW Electrical 1PH 115/230V 50/60HZ   Type Centrifugal Mag Drive Inlet 1"FPT Outlet 1/2"MPT Wet End Polypropylene (Front and Rear Housing, Impeller), Viton (O-Ring), Ceramic (Shaft, Thrust Washers) Motor Options Available in Explosion Proof  

March LC-5C-MD Magnetic Drive Pump 230V The most common application for the LC-5C-MD Magnetic Drive Pump is for marine air conditioning and fountains. This pump will handle up to a 48,000 BTU Air Conditioner March Pump's industrial LC-5C-MD is an American submersible seal-less centrifugal magnetic drive pump. It is capable of generating a maximum flow of 15 gallons per minute at 2 feet, and its maximum head is 27 Feet (or around 11PSI).  The LC-5C-MD pump may be used submerged or not submerged. The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Buna N, Stainless Steel, Ceramic, and Ceramic Magnet.  When submerged, Epoxy, Noryl, and the Cord are also in contact with the solution. The inlet connection is 1 inch female pipe thread, and the outlet is 0.5 inch male pipe thread. The standard motor is a 1 Phase 115V or 230V 0.125 Horsepower motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 130 Fahrenheit or 54 Celsius. The March LC-5C-MD centrifugal magnetic drive pump is capable of handling fresh water, salt water, and mild chemicals.   Unit System 60Hz 50Hz Max Flow 14.5 GPM 54.8 LPM Max Head 27 FT 6 M Power .125 HP .097 KW Electrical 115V 50/60HZ or 230V 50/60HZ Submersible Yes   Type Centrifugal Mag Drive Inlet 1"FPT Outlet 1/2"MPT Wet End Polypropylene (Front and Rear Housing, Impeller), Buna N (O-Ring), 316 Stainless Steel (Shaft, Cooling Tube), Ceramic (Shaft, Thrust Washers), Ceramic Magnet Uses Submersible or Open Air When submerged, the following is also in contact with the solution Epoxy, Noryl, Cord

March AC-4C-MD Magnetically Coupled Pump 115V Applications for the AC-4C-MD Magnetic Drive Pump include electronic medical equipment, etching machines, photo processing equipment, hospital thermal blankets, and food heating cabinets. March Pump's industrial AC-4C-MD is an American seal-less centrifugal magnetic drive pump ideal for applications such as chemical recirculation, chemical transfer, and scrubber systems. It is capable of generating a maximum flow of 14 gallons per minute at 1 feet, and its maximum head is 21.5 Feet (or around 9PSI). The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Buna N, Ceramic, and Ceramic Magnet. The inlet connection is 1 inch female pipe thread, and the outlet is 0.75 inch male pipe thread. The standard motor is a 1 Phase 115V or 230V 0.83 Horsepower fan cooled motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheit or 87 Celsius. The March AC-4C-MD centrifugal magnetic drive pump is capable of handling mildly or highly corrosive chemicals, acids, and solvents.   Unit System 60Hz 50Hz Max Flow 14 GPM 50 LPM Max Head 21.5 FT 4.7 M Power .083 HP .062 KW Electrical 115V 50/60HZ or 230V 50/60HZ   Type Centrifugal Mag Drive Inlet 1"FPT Outlet 1/2"MPT Wet End Polypropylene (Front and Rear Housing, Impeller), Buna N (O-Ring), Ceramic (Shaft, Thrust Washers), Ceramic Magnet

Applications for the March AC-1A-MD-1/2 Magnetic Drive Pump include chemical transfer, photographic processing equipment, refrigeration systems, and water displays.   The AC-1A-MD-1/2 Part # 0115-0064-0200 has pumped Acetone, Ammonium Chloride, Ammonium Chloride, Ammonium Hydroxide, Citric Acid, Ethylene Glycol, Magnesium Nitrate, Potassium Carbonate, Sodium Borate, Fresh Water, Salt Water, and many more chemicals.  The AC-1A-MD-1/2 may have been modified to handle these chemicals.    March Pump's industrial AC-1A-MD-1/2 is an American seal-less centrifugal magnetic drive pump ideal for applications such as chemical recirculation and chemical transfer. It is capable of generating a maximum flow of 3 gallons per minute at 0.25 feet, and its maximum head is 4.6 Feet (or around 2PSI). The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Buna N, Nylon, Carbon/Teflon, Stainless Steel, and Ceramic Magnet. The inlet connection is 0.5 inch smooth, and the outlet is 0.5 inch smooth. The standard motor is a 1 Phase 115V or 230V 0.05 Horsepower motor, which can be run on 60 hertz on 115V or 50 and 60 hertz on 230V (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheit or 87 Celsius. The March AC-1A-MD-1/2 centrifugal magnetic drive pump is capable of handling mildly or highly corrosive chemicals, acids, and solvents. To determine if the March AC-1A-MD-1/2 is suitable for your application, please contact March Pump.      Unit System 60Hz 50Hz Max Flow 3 GPM 9 LPM Max Head 4.6 FT 1 M Power .005 HP .003 KW Electrical 115V 60HZ       230V 50/60HZ   Type Centrifugal Mag Drive Inlet 1/2"OD Outlet 1/2"OD Wet End Polypropylene (Front and Rear Housing), Buna N (O-Ring), Nylon (Impeller), Carbon/Teflon (Thrust Washer), 316 Stainless Steel (Shaft), Ceramic Magnet   Part # 0115-0064-0200

Applications for the March AC-1A-MD-1/2 Magnetic Drive Pump include chemical transfer, photographic processing equipment, refrigeration systems, and water displays.   The AC-1A-MD-1/2 Part # 0115-0064-0100 has pumped Acetone, Ammonium Chloride, Ammonium Chloride, Ammonium Hydroxide, Citric Acid, Ethylene Glycol, Magnesium Nitrate, Potassium Carbonate, Sodium Borate, Fresh Water, Salt Water, and many more chemicals.  The AC-1A-MD-1/2 may have been modified to handle these chemicals.    March Pump's industrial AC-1A-MD-1/2 is an American seal-less centrifugal magnetic drive pump ideal for applications such as chemical recirculation and chemical transfer. It is capable of generating a maximum flow of 3 gallons per minute at 0.25 feet, and its maximum head is 4.6 Feet (or around 2PSI). The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Buna N, Nylon, Carbon/Teflon, Stainless Steel, and Ceramic Magnet. The inlet connection is 0.5 inch smooth, and the outlet is 0.5 inch smooth. The standard motor is a 1 Phase 115V or 230V 0.05 Horsepower motor, which can be run on 60 hertz on 115V or 50 and 60 hertz on 230V (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheit or 87 Celsius. The March AC-1A-MD-1/2 centrifugal magnetic drive pump is capable of handling mildly or highly corrosive chemicals, acids, and solvents.     Unit System 60Hz 50Hz Max Flow 3 GPM 9 LPM Max Head 4.6 FT 1 M Power .005 HP .003 KW Electrical 115V 60HZ     230V 50/60HZ   Type Centrifugal Mag Drive Inlet 1/2"OD Outlet 1/2"OD Wet End Polypropylene (Front and Rear Housing), Buna N (O-Ring), Nylon (Impeller), Carbon/Teflon (Thrust Washer), 316 Stainless Steel (Shaft), Ceramic Magnet   Part # 0115-0064-0100

Applications for the March AC-1A-MD-3/8 Magnetic Drive Pump include photographic processing equipment, refrigeration systems, and water displays.   The AC-1A-MD-3/8 Part # 0115-0064-0300 has pumped Acetone, Ammonium Chloride, Ammonium Chloride, Ammonium Hydroxide, Citric Acid, Ethylene Glycol, Magnesium Nitrate, Potassium Carbonate, Sodium Borate, Fresh Water, Salt Water, and many more chemicals.  The AC-1A-MD-3/8 may have been modified to handle these chemicals.    March Pump's industrial AC-1A-MD-3/8 is an American seal-less centrifugal magnetic drive pump ideal for applications such as chemical recirculation and chemical transfer. It is capable of generating a maximum flow of 2.3 gallons per minute at 0.25 feet, and its maximum head is 4.6 Feet (or around 2PSI). The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Buna N, Nylon, Carbon/Teflon, Stainless Steel, and Ceramic Magnet. The inlet connection is 0.375 inch smooth, and the outlet is 0.375 inch smooth. The standard motor is a 1 Phase 115V or 230V 0.05 Horsepower motor, which can be run on 60 hertz on 115V or 50 and 60 hertz on 230V (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheit or 87 Celsius. The March AC-1A-MD-3/8 centrifugal magnetic drive pump is capable of handling mildly or highly corrosive chemicals, acids, and solvents.     Unit System 60Hz 50Hz Max Flow 2.3 GPM 8.7 LPM Max Head 4.6 FT 1 M Power .005 HP .003 KW Electrical 115V 60HZ      230V 50/60HZ   Type Centrifugal Mag Drive Inlet 3/8"OD Outlet 3/8"OD Wet End Polypropylene (Front and Rear Housing), Buna N (O-Ring), Nylon (Impeller), Carbon/Teflon (Thrust Washer), 316 Stainless Steel (Shaft), Ceramic Magnet     Part # 0115-0064-0300  

Applications for the March AC-1A-MD-3/8 Magnetic Drive Pump include photographic processing equipment, refrigeration systems, and water displays.   The AC-1A-MD-3/8 has pumped Acetone, Ammonium Chloride, Ammonium Chloride, Ammonium Hydroxide, Citric Acid, Ethylene Glycol, Magnesium Nitrate, Potassium Carbonate, Sodium Borate, Fresh Water, Salt Water, and many more chemicals.  The AC-1A-MD-3/8 may have been modified to handle these chemicals.   March Pump's industrial AC-1A-MD-3/8 is an American seal-less centrifugal magnetic drive pump ideal for applications such as chemical recirculation and chemical transfer. It is capable of generating a maximum flow of 2.3 gallons per minute at 0.25 feet, and its maximum head is 4.6 Feet (or around 2PSI). The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Buna N, Nylon, Carbon/Teflon, Stainless Steel, and Ceramic Magnet. The inlet connection is 0.375 inch smooth, and the outlet is 0.375 inch smooth. The standard motor is a 1 Phase 115V or 230V 0.05 Horsepower motor, which can be run on 60 hertz on 115V or 50 and 60 hertz on 230V (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheit or 87 Celsius. The March AC-1A-MD-3/8 centrifugal magnetic drive pump is capable of handling mildly or highly corrosive chemicals, acids, and solvents.      Unit System 60Hz 50Hz Max Flow 2.3 GPM 8.7 LPM Max Head 4.6 FT 1 M Power .005 HP .003 KW Electrical 115V 60HZ          230V 50/60HZ   Type Centrifugal Mag Drive Inlet 3/8"OD Outlet 3/8"OD Wet End Polypropylene (Front and Rear Housing), Buna N (O-Ring), Nylon (Impeller), Carbon/Teflon (Thrust Washer), 316 Stainless Steel (Shaft), Ceramic Magnet

Applications for the AC-1C-MD Magnetic Drive Pump include chemical transfer photographic processing equipment, refrigeration systems, and water displays.   The AC-1C-MD Part # 0115-0070-0100 has pumped Acetone, Ammonium Chloride, Ammonium Chloride, Ammonium Hydroxide, Citric Acid, Ethylene Glycol, Magnesium Nitrate, Potassium Carbonate, Sodium Borate, Fresh Water, Salt Water, and many more chemicals.  The AC-1C-MD may have been modified to handle these chemicals.    March Pump's industrial AC-1C-MD is an American seal-less centrifugal magnetic drive pump ideal for applications such as chemical recirculation and chemical transfer. It is capable of generating a maximum flow of 3 gallons per minute at 0.25 feet, and its maximum head is 4.6 Feet (or around 2PSI). The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Buna N, Nylon, Carbon/Teflon, Stainless Steel, and Ceramic Magnet. The inlet connection is 0.25 inch smooth, and the outlet is 0.25 inch smooth. The standard motor is a 1 Phase 115V or 230V 0.05 Horsepower motor, which can be run on 60 hertz on 115V or 50 and 60 hertz on 230V (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheit or 87 Celsius. The March AC-1C-MD centrifugal magnetic drive pump is capable of handling mildly or highly corrosive chemicals, acids, and solvents.      Unit System 60Hz 50Hz Max Flow 3 GPM 9 LPM Max Head 4.6 FT 1 M Power .005 HP .003 KW Electrical 115V 60HZ       230V 50/60HZ   Type Centrifugal Mag Drive Inlet 1/4"MPT Outlet 1/4"MPT Wet End Polypropylene (Front and Rear Housing), Buna N (O-Ring), Nylon (Impeller), Carbon/Teflon (Thrust Washer), 316 Stainless Steel (Shaft), Ceramic Magnet   Part # 0115-0070-0100  

March AC-2AP-MD  115vac Applications for the AC-2AP-MD Mag Drive include etching equipment, photographic processing equipment, ice makers, ice flakers, plate processors, and marine air conditioning.   March Pump's industrial AC-2AP-MD is an American seal-less centrifugal magnetic drive pump ideal for applications such as chemical recirculation and chemical transfer. It is capable of generating a maximum flow of 5 gallons per minute at 2 feet, and its maximum head is 13 Feet (or around 5.5PSI). The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Viton, Ceramic, and Ceramic Magnet. The inlet connection is 0.75 inch smooth, and the outlet is 0.5 inch smooth. The standard motor is a 1 Phase 115V or 230V 0.025 Horsepower fan cooled motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheit or 87 Celsius. The March AC-2AP-MD centrifugal magnetic drive pump is capable of handling mildly or highly corrosive chemicals, acids, and solvents.   Max Flow 250 GPH 18.5 LPM up to a 6000 BTU Air Conditioner Max Head 13 FT 2.7 M Power .025 HP .018 KW Electrical 115V 50/60HZ   Type Centrifugal Mag Drive Inlet 3/4"OD Outlet 1/2"OD Wet End Polypropylene (Front and Rear Housing, Impeller), Viton (O-Ring), Ceramic (Shaft, Thrust Washer), Ceramic Magnet

March AC-2CP-MD Mag Drive March Pump's industrial AC-2CP-MD is an American seal-less centrifugal magnetic drive pump ideal for applications such as chemical recirculation and chemical transfer. It is capable of generating a maximum flow of 5 gallons per minute at 2 feet, and its maximum head is 13 Feet (or around 5.5PSI). The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Viton, Ceramic, and Ceramic Magnet. The inlet connection is 0.375 female pipe thread and 0.75 male pipe thread, and the outlet is 0.25 inch male pipe thread. The standard motor is a 1 Phase 115V or 230V 0.025 Horsepower fan cooled motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options). The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheit or 87 Celsius. The March AC-2CP-MD centrifugal magnetic drive pump is capable of handling mildly or highly corrosive chemicals, acids, and solvents.   Unit System 60Hz 50Hz Max Flow 5 GPM 18.5 LPM Max Head 13 FT 2.7 M Power .025 HP .018 KW Electrical 115V 60HZ   Type Centrifugal Mag Drive Inlet 3/8"FPT & 3/4"MPT Outlet 1/4"MPT Wet End Polypropylene (Front and Rear Housing, Impeller), Viton (O-Ring), Ceramic (Shaft, Thrust Washer), Ceramic Magnet   March 0125-0069-0100