March AC-5C-MD Reverse Osmosis Feed Pump 230V Applications for the AC-5C-MD Magnetic Drive Pump include chemical recirculation, refrigerators, small scrubbers, detergent mixers, computer cooling, carbon arc furnace cooling, and marine air conditioners. March Pump's industrial AC-5C-MD is an American seal-less centrifugal magnetic drive pump ideal for applications such as chemical recirculation, chemical transfer, and scrubber systems. It is capable of generating a maximum flow of 17 gallons per minute at 1 feet, and its maximum head is 27 Feet (or around 11PSI). The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Buna N, Ceramic, and Ceramic Magnet. The inlet connection is 1 inch female pipe thread, and the outlet is 0.5 inch male pipe thread. The standard motor is a 1 Phase 115V or 230V 0.125 Horsepower fan cooled motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheit. The March AC-5C-MD centrifugal magnetic drive pump is capable of handling mildly or highly corrosive chemicals, acids, and solvents.   Max Flow 17 GPM 60 LPM Max Head 27 FT 6 M Power .125 HP .093 KW Electrical 230V 50/60HZ   Type Centrifugal Mag Drive Inlet 1"FPT Outlet 1/2"MPT Wet End Polypropylene (Front and Rear Housing, Impeller), Buna N (O-Ring), Ceramic (Shaft, Thrust Washers), Ceramic Magnet  

March LC-5C-MD Magnetic Drive Pump 230V The most common application for the LC-5C-MD Magnetic Drive Pump is for marine air conditioning and fountains. This pump will handle up to a 48,000 BTU Air Conditioner March Pump's industrial LC-5C-MD is an American submersible seal-less centrifugal magnetic drive pump. It is capable of generating a maximum flow of 15 gallons per minute at 2 feet, and its maximum head is 27 Feet (or around 11PSI).  The LC-5C-MD pump may be used submerged or not submerged. The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Buna N, Stainless Steel, Ceramic, and Ceramic Magnet.  When submerged, Epoxy, Noryl, and the Cord are also in contact with the solution. The inlet connection is 1 inch female pipe thread, and the outlet is 0.5 inch male pipe thread. The standard motor is a 1 Phase 115V or 230V 0.125 Horsepower motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 130 Fahrenheit or 54 Celsius. The March LC-5C-MD centrifugal magnetic drive pump is capable of handling fresh water, salt water, and mild chemicals.   Unit System 60Hz 50Hz Max Flow 14.5 GPM 54.8 LPM Max Head 27 FT 6 M Power .125 HP .097 KW Electrical 115V 50/60HZ or 230V 50/60HZ Submersible Yes   Type Centrifugal Mag Drive Inlet 1"FPT Outlet 1/2"MPT Wet End Polypropylene (Front and Rear Housing, Impeller), Buna N (O-Ring), 316 Stainless Steel (Shaft, Cooling Tube), Ceramic (Shaft, Thrust Washers), Ceramic Magnet Uses Submersible or Open Air When submerged, the following is also in contact with the solution Epoxy, Noryl, Cord

March AC-5C-MD Reverse Osmosis Feed Pump 115 Volt Applications for the AC-5C-MD Magnetic Drive Pump include chemical recirculation, refrigerators, small scrubbers, detergent mixers, computer cooling, carbon arc furnace cooling, and marine air conditioners. March Pump's industrial AC-5C-MD is an American seal-less centrifugal magnetic drive pump ideal for applications such as chemical recirculation, chemical transfer, and scrubber systems. It is capable of generating a maximum flow of 17 gallons per minute at 1 feet, and its maximum head is 27 Feet (or around 11PSI). The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Buna N, Ceramic, and Ceramic Magnet. The inlet connection is 1 inch female pipe thread, and the outlet is 0.5 inch male pipe thread. The standard motor is a 1 Phase 115V or 230V 0.125 Horsepower fan cooled motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options). The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheit or 87 Celsius. The March AC-5C-MD centrifugal magnetic drive pump is capable of handling mildly or highly corrosive chemicals, acids, and solvents.   Max Flow 17 GPM 60 LPM Max Head 27 FT 6 M Power .125 HP .093 KW Electrical 115V 50/60HZ   Type Centrifugal Mag Drive Inlet 1"FPT Outlet 1/2"MPT Wet End Polypropylene (Front and Rear Housing, Impeller), Buna N (O-Ring), Ceramic (Shaft, Thrust Washers), Ceramic Magnet   Available with 750 Priming Chamber

Applications for the AC-2CP-MD Mag Drive include etching equipment, photographic processing equipment, ice makers, ice flakers, plate processors, and marine air conditioning.    March Pump's industrial AC-2CP-MD is an American seal-less centrifugal magnetic drive pump ideal for applications such as chemical recirculation and chemical transfer. It is capable of generating a maximum flow of 5 gallons per minute at 2 feet, and its maximum head is 13 Feet (or around 5.5PSI). The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Viton, Ceramic, and Ceramic Magnet. The inlet connection is 0.375 female pipe thread and 0.75 male pipe thread, and the outlet is 0.25 inch male pipe thread. The standard motor is a 1 Phase 115V or 230V 0.025 Horsepower fan cooled motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheit or 87 Celsius. The March AC-2CP-MD centrifugal magnetic drive pump is capable of handling mildly or highly corrosive chemicals, acids, and solvents.     Unit System 60Hz 50Hz Max Flow 5 GPM 18.5 LPM Max Head 13 FT 2.7 M Power .025 HP .018 KW Electrical 115V 50/60HZ or 230V 50/60HZ     Type Centrifugal Mag Drive Inlet 3/8"FPT & 3/4"MPT Outlet 1/4"MPT Wet End Polypropylene (Front and Rear Housing, Impeller), Viton (O-Ring), Ceramic (Shaft, Thrust Washer), Ceramic Magnet

Applications for the AC-3AP-MD Magnetic Drive Pump include ice makers, laboratory and medical equipment, vapor degreasers, and marine air conditioning systems.    March Pump's industrial AC-3AP-MD is an American seal-less centrifugal magnetic drive pump ideal for applications such as chemical recirculation, chemical transfer, and scrubber systems. It is capable of generating a maximum flow of 10 gallons per minute at 1 feet, and its maximum head is 20.5 Feet (or around 9PSI). The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Buna N, Ceramic, and Ceramic Magnet. The inlet connection is 0.75 inch smooth, and the outlet is 0.5 inch smooth. The standard motor is a 1 Phase 115V or 230V 0.6 Horsepower fan cooled motor, which can be run on 60 hertz on 115V or 50 and 60 hertz on 230V (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheit or 87 Celsius. The March AC-3AP-MD centrifugal magnetic drive pump is capable of handling mildly or highly corrosive chemicals, acids, and solvents.     Unit System 60Hz 50Hz Max Flow 10 GPM 33 LPM Max Head 20.5 FT 4.5 M Power .06 HP .049 KW Electrical 115V 60HZ or 230V 50/60HZ     Type Centrifugal Mag Drive Inlet 3/4"OD Outlet 1/2"OD Wet End Polypropylene (Front and Rear Housing, Impeller), Buna N (O-Ring), Ceramic (Shaft, Thrust Washer), Ceramic Magnet

Applications for the AC-3CP-MD Magnetic Drive Pump include ice makers, laboratory and medical equipment, vapor degreasers, and marine air conditioning systems.    March Pump's industrial AC-3CP-MD is an American seal-less centrifugal magnetic drive pump ideal for applications such as chemical recirculation, chemical transfer, and scrubber systems. It is capable of generating a maximum flow of 10 gallons per minute at 1 feet, and its maximum head is 20.5 Feet (or around 9PSI). The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Buna N, Ceramic, and Ceramic Magnet. The inlet connection is 0.75 inch female pipe thread, and the outlet is 0.5 inch male pipe thread. The standard motor is a 1 Phase 115V or 230V 0.6 Horsepower fan cooled motor, which can be run on 60 hertz on 115V or 50 and 60 hertz on 230V (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheit or 87 Celsius. The March AC-3CP-MD centrifugal magnetic drive pump is capable of handling mildly or highly corrosive chemicals, acids, and solvents.     Unit System 60Hz 50Hz Max Flow 10 GPM 33 LPM Max Head 20.5 FT 4.5 M Power .066 HP .049 KW Electrical 115V 60HZ or 230V 50/60HZ     Type Centrifugal Mag Drive Inlet 3/4"FPT Outlet 1/2"MPT Wet End Polypropylene (Front and Rear Housing, Impeller), Buna N (O-Ring), Ceramic (Shaft, Thrust Washer), Ceramic Magnet

March 1A-MD 3/8 Mag Drive Pump March Pump's industrial 1A-MD-3/8 is an American submersible seal-less centrifugal magnetic drive pump. It is capable of generating a maximum flow of 2.3 gallons per minute at 0.25 feet, and its maximum head is 4.5 Feet (or around 2PSI).  The 1A-MD-3/8 pump may be used submerged or not submerged. The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Buna N, Nylon, Carbon/Teflon, and Stainless Steel.  When submerged, Epoxy, Noryl, and the SJT Cord are also in contact with the solution. The inlet connection is 3/8 inch smooth, and the outlet is 3/8 inch smooth. The standard motor is a 1 Phase 115V or 230V 0.005 Horsepower motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheit or 160 Celsius in open air, or 87 Fahrenheit or 71 Celsius if submerged. The March 1A-MD-3/8 centrifugal magnetic drive pump is capable of handling fresh water, salt water, and mild chemicals.   Perfect for Applications Including Applications for the 1A-MD-3/8 Magnetic Drive Pump include chemical transfer, photographic processing equipment, refrigeration systems, and water displays.   Great for Chemicals Including The 1A-MD-3/8 has pumped Acetone, Ammonium Chloride, Ammonium Chloride, Ammonium Hydroxide, Citric Acid, Ethylene Glycol, Magnesium Nitrate, Potassium Carbonate, Sodium Borate, Fresh Water, Salt Water, and many more chemicals.  The 1A-MD-3/8 may have been modified to handle these chemicals.    Type: Centrifugal Mag Drive Inlet: 3/8"OD Outlet: 3/8"OD Wet End: Polypropylene (Front Housing, Rear Housing, Impeller), Buna N (O-Ring), Carbon/Teflon (Thrust Washer), 316 Stainless Steel (Shaft) Uses: Submersible or Open Air When submerged, the following is also in contact with the solution, Epoxy, Noryl, SJT Cord    

Applications for the TE-5.5K-MD Magnetic Drive Pump include chemical recirculation, chemical transfer, refrigerators, scrubber systems, detergent mixers, computer cooling, carbon arc furnace cooling, silver recovery systems, and marine air conditioners.   The TE-5.5K-MD has pumped Acetic Acid, Citric Acid, Ethylene Glycol, Formaldehyde, Hydrochloric Acid (Muriatic), Hydrofluoric Acid, Hydrogen Peroxide, Nitric Acid, Phosphoric Acid, Potassium Chloride, Sodium Chloride, Sodium Hypochlorite, Sulfuric Acid, Fresh Water, Salt Water, DI Water, and many more chemicals..  The TE-5.5K-MD may have been modified to handle these chemicals.     March Pump's industrial TE-5.5K-MD is an American seal-less centrifugal magnetic drive pump ideal for applications such as chemical recirculation, chemical transfer, and scrubber systems. It is capable of generating a maximum flow of 30 gallons per minute at 11 feet, and its maximum head is 41 Feet (or around 18PSI). The standard wet end (the materials that come into contact with the solution) is composed of carbon filled Kynar (PVDF), Viton, Carbon, and Ceramic. The inlet connection is 1 inch female pipe thread, and the outlet is 0.75 inch male pipe thread. The standard motor is a 1 Phase 115/230V or 3 Phase 230/460V 0.33 Horsepower totally enclosed fan cooled motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 75PSI, and the maximum liquid temperature is 200 Fahrenheit or 93 Celsius. The March TE-5.5K-MD centrifugal magnetic drive pump is capable of handling mildly or highly corrosive chemicals, acids, and solvents.     Unit System 60Hz 50Hz Max Flow 30 GPM 102 LPM Max Head 41 FT 9 M Power .33 HP .248 KW Electrical 1PH 115/230V      3PH 230/460V 50/60HZ     Type Centrifugal Mag Drive Inlet 1"FPT Outlet 3/4"MPT Wet End Carbon Filled Kynar (Front and Rear Housing, Impeller), Viton (O-Ring), Ceramic (Shaft, Thrust Washers)

March 0150-0040-1000 Magnetic Drive Pump AC-5M-MD March Pump’s industrial AC-5M-MD is an American seal-less centrifugal magnetic drive pump ideal for applications such as chemical recirculation, chemical transfer, and scrubber systems. It is capable of generating a maximum flow of 17 gallons per minute at 1 feet, and its maximum head is 27 Feet (11PSI). The pump is Ignition Protected per SAE J1171 and ISO 8846, and has extended run dry protection thru the use of a carbon bushing. It is capable of 48,000 BTU a hour.   Max Flow: 64.4 LPM Max Head: 8.2 M Power: 0.093 KW   Electrical/Air: 230V 50/60Hz   Motor 3 Foot Cord 60Hz: 1Ph 230V 0.125HP/0.093kW, 2.1 AMPS, 3450 RPM 50Hz: 1Ph 230V 0.125HP/0.093kW, 1 AMPS, 2850 RPM   Inlet: 1"FPT Outlet: 1/2"MPT   Wet End: Polypropylene (Rear Housing, Impeller), Noryl (Front Housing) Buna N (O-Ring), 316 Stainless Steel (Shaft), Carbon (Impeller Bushing) Ceramic (Thrust Washers), Ceramic Magnet Max Internal Pressure: 50 PSI / 3.4 bar Max Liquid Temperature: 190 °F / 87 °C Ignition Protected per SAE J1171 and ISO 8846: UL Listed Motor   This pump is capable of generating a maximum flow of 17 gallons per minute at 1 feet, and its maximum head is 27 Feet (11PSI).  It is capable of 48,000 BTU a hour.  The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Noryl,  Buna N, Carbon, 316 Stainless Steel, Ceramic, and Ceramic Magnet. The inlet connection is 1 inch female pipe thread, and the outlet is 1/2 inch male pipe thread. The standard motor is a 1 Phase 115V or 230V 0.125 Horsepower fan cooled motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheit or 87 Celsius.     The pump is Ignition Protected per SAE J1171 and ISO 8846.  The impeller has a carbon bushing allowing the pump to run dry longer before suffering damage.  

March Pump Mag-Drive Centrifugal Pump Kynar Single Phase 2Hp  • March TE-7.5K-MD Series pumps are the only ones in the March product line with all molded parts constructed of natural Kynar. This makes them ideal for super sensitive applications where even a trace of foreign matter is unacceptable, such as microchip manufacturing. Various bushing materials are available for such applications where purity of solutions is critical. • Flow rates range from 10 GPM (35 LPM) minimum to 82 GPM (268 LPM) maximum. Head ranges from 0 ft. to a maximum of 85 ft. (18m). Other application examples include plating equipment and D.I. water systems. • Standard with the March TE-7.5K-MD Series pump is a 2 HP (1.49 kw), 230/460-volt, three-phase, totally enclosed motor. Severe duty and explosion-proof motors are also available. Standard port configuration is a 2" MPT inlet with a 1 1/2" MPT outlet. • All plastic parts of the pump are molded out of natural Kynar (PVDF). The stationary spindle and Thrust Washers are made of porcelain ceramic. The O-ring for the housing is Viton rubber. The bushings in the impeller Assembly are carbon. There are no other materials in contact with the solution.    March Pump Mag-Drive Centrifugal Pump Kynar 115/230V 2HP TEFC 82GPM 2"MPT Inlet, 1 1/2"MPT Outlet

March 140 Series Mag-Drive Centrifugal Pumps     • Use the compact Series 140 pumps where maximum flow with minimal pressure is desired. Maximum flow is 12.5 GPM (55 LPM) and maximum head is 11.5 ft. (2.5m) • Series 140 pumps use Open Frame Skeleton Type Motors or 1/20 HP (.037 kw), 2900 rpm 115 volt air-cooled motors. • Materials used are glass-filled polypropylene, Buna N rubber, ceramic, Ryton®, Teflon® and Viton®. • Maximum Liquid Temperature is 190 degrees F     March Pump Mag-Drive Centrifugal Pump 230V Open Frame Skeleton Motor 12.5GPM 1 1/8" Hose Inlet, 7/8" Hose Outlet  

Applications for the 809-BR Magnetic Drive Pump include hot water systems and solar heating.    March Pump's industrial 809-BR is an American seal-less centrifugal magnetic drive pump ideal for applications such as hot water systems. It is capable of generating a maximum flow of 4.5 gallons per minute at 0.5 feet, and its maximum head is 4.3 Feet (or around 1.8PSI). The standard wet end (the materials that come into contact with the solution) is composed of Bronze, Stainless Steel, Teflon, Silicone and Ryton/Teflon/Glass. The inlet connection is 0.5 male pipe thread, and the outlet is 0.5 inch male pipe thread. The standard motor is a 1 Phase 115V or 230V 0.01 Horsepower fan cooled motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 150PSI, and the maximum liquid temperature is 250 Fahrenheit or 121 Celsius.     Unit System 60Hz 50Hz Max Flow 4.5 GPM 10.3 LPM Max Head 4.3 FT .92 M Power .01 HP .007 KW Electrical 115V 50/60HZ or 230V 50/60HZ     Type Centrifugal Mag Drive Inlet 1/2"MPT Outlet 1/2"MPT Wet End Bronze (Front Housing), Stainless Steel (Rear Housing, Shaft), Teflon (Thrust Washer), Silicone (O-Ring), Ryton/Teflon/Glass (Impeller)

March 809 815 Series Mag-Drive Centrifugal Pumps The March MAGNE-BOOST Hydronic hot water booster pumps are a non-self priming unit built to handle liquid transfer in heating and cooling operations. Typical applications include home heating systems, solar heating systems, heat recovery systems and recirculating water in domestic and commercial hot water tanks. These pumps are not food rated. • Brewery pump - the March 809 and 815 series of pumps are commonly used by Home Brewers and Breweries. • Maximum liquid temperature for the 809 and 815 series is 250 F. • Port configurations include in-line and center inlet with side discharge. • Construction materials: Bronze, Stainless Steel, Ryton/Polysulfil Plastic. Impellers are Teflon plastic. • There are many motor options available Including AC, DC and High Speed versions for added flow.   March Pump Mag-Drive Centrifugal Pump Bronze with Base 24VDC High Speed 7.5GPM 1/2"MPT Ports  

March 809 815 Series Mag-Drive Centrifugal Pumps Bronze Center Inlet 115V 4.5GPM   The March MAGNE-BOOST Hydronic hot water booster pumps are a non-self priming unit built to handle liquid transfer in heating and cooling operations. Typical applications include home heating systems, solar heating systems, heat recovery systems and recirculating water in domestic and commercial hot water tanks. These pumps are not food rated. • Brewery pump - the March 809 and 815 series of pumps are commonly used by Home Brewers and Breweries. • Maximum liquid temperature for the 809 and 815 series is 250 F. • Port configurations include in-line and center inlet with side discharge. • Construction materials: Bronze, Stainless Steel, Ryton/Polysulfil Plastic. Impellers are Teflon plastic. • There are many motor options available Including AC, DC and High Speed versions for added flow.     March Pump Mag-Drive Centrifugal Pump Bronze Center Inlet 115V 4.5GPM 3/4"MPT Inlet, 1/2"MPT Outlet  

March Mag-Drive Centrifugal Pumps Bronze Center Inlet 12VDC 5.5GPM     The March MAGNE-BOOST Hydronic hot water booster pumps are a non-self priming unit built to handle liquid transfer in heating and cooling operations. Typical applications include home heating systems, solar heating systems, heat recovery systems and recirculating water in domestic and commercial hot water tanks. These pumps are not food rated. • Brewery pump - the March 809 and 815 series of pumps are commonly used by Home Brewers and Breweries. • Maximum liquid temperature for the 809 and 815 series is 250 F. • Port configurations include in-line and center inlet with side discharge. • Construction materials: Bronze, Stainless Steel, Ryton/Polysulfil Plastic. Impellers are Teflon plastic. • There are many motor options available Including AC, DC and High Speed versions for added flow.     March Pump Mag-Drive Centrifugal Pump Bronze Center Inlet 12VDC 5.5GPM 3/4"MPT Inlet, 1/2"MPT Outlet