Cal MS-900-6-2B Pump 900 Gph 220V W/Base Cal Pump Centrifugal Pump, Stainless and Bronze Body, 900GPH No Flow Control, 230V 50/60Hz with 6 Foot Power Cord, 3/4" Male NPT Inlet and 1/2" Male NPT Outlet, Viton Seal, Can Run in Open Air or Submersed, For Fresh or Salt Water up to 110F, Can Be Used With Marine AC Units up to 36,000BTU, Approved for: UL, CE, ABYC and USCG. Includes 2 Nylon Mounting Brackets

Cal MS-580-20-2B Pump 580Gph 230V 50/60 Cal Pump Centrifugal Pump, Stainless and Bronze Body, 580GPH No Flow Control, 230V 50/60Hz with 20 Foot Power Cord, 3/4" Male NPT Inlet and 1/2" Male NPT Outlet, Viton Seal, Can Run in Open Air or Submersed, For Fresh or Salt Water up to 110F, Can Be Used With Marine AC Units up to 24,000BTU, Approved for: UL, CE, ABYC and USCG. Includes 2 Nylon Mounting Brackets

Cal MS-900-6B Pump 900Gph 115V W/Base Cal Pump Centrifugal Pump, Stainless and Bronze Body, 900GPH No Flow Control, 115V 60Hz with 6 Foot Power Cord, 3/4" Male NPT Inlet and 1/2" Male NPT Outlet, Viton Seal, Can Run in Open Air or Submersed, For Fresh or Salt Water up to 110F, Can Be Used With Marine AC Units up to 36,000BTU, Approved for: UL, CE, ABYC and USCG. Includes 2 Nylon Mounting Brackets

Cal MS-1200-6B Pump 1200Gph 115V with Base and Cord Centrifugal Pump Stainless and Bronze Body 1200GPH No Flow Control 115V 60Hz with 6 Foot Power Cord 3/4" Male NPT Inlet and 1/2" Male NPT Outlet Viton Seal Can Run in Open Air or Submersed For Fresh or Salt Water up to 110F Can Be Used With Marine AC Units up to 60,000BTU Approved for: UL, CE, ABYC and USCG Includes 2 Nylon Mounting Brackets

Cal Pump MS-580-20 Pump 580Gph 115/120V 20'Cord Cal Marine Pumps are certified to the following standards: UL, CE, ABYC and U.S. Coast Guard Premium stainless steel and bronze construction for longevity 115 Volts - 20ft power cord - 3 wire; black, white, green ( NO PLUG ON END ) Suitable for fresh, salt or chlorinated water applications (max of 3-5 ppm) Can be used in hot water applications up to 110°F Extremely quiet operation Use submerged or in open air (below water level) Viton seals suitable for harsh marine applications 3/4" MPT Intake and 1/2" MPT Discharge Approximate dimensions: 4-1/2" x 6-1/4"  

Roper Pump 18AM02-2B A Series Gear Pump W/Rv Ports: 3/8 in. Flow-Rate: 7.2 GPM Max RPM: 3600 GPR: .002 Mtg: Flange   Roper A Series pumps are adaptable to a wide range of applications pumping clean ?uids, such as pressure lubrication, hydraulic service, fuel supply or general liquid transfer.   These pumps are designed to operate at standard motor speeds, with provisions for ?ange or foot mounting. The internal bearings are lubricated by the ?uid being pumped. With only two moving parts, the pumps run quietly.   3/8" and 3/4" pumps are 300 PSI and all 1 1/4" - 2" pumps are 150 PSI   Specifications Type of Pump: Positive Displacement Gear Pump Materials of Construction: Cast Iron Housing, Ductile Iron Gears and Drive Shafts, Bronze Bearings and Steel Idler Shafts. Priming: Self Priming Seal Material: Mechanical Seal (AM) Viscosity: Up to 2,200 cSt, 10,000 SSU

Cal Msr-12 Repair Kit For 1200  Cal Pump Repair Kit for MS-1200 MS1200 Pumps, includes: Impeller, Volute, O-Ring, Hardware. No Flow Control Valve

Gianneschi ECOJET-2B-CE-24V Fresh Water System Pressurized fresh water, equipped with flow and pressure sensors managed by an electronic board, replaces the traditional expansion vessel system with the following advantages:   Reduction of the number of pump starts with consequent reduction of wear - Reduction of overall dimensions - Protection of the pump against dry running - Maintenance of the pressure value during water supply - Display of the pump status (Power on, Pump on, Failure) - Automatic reset (when voltage is restored) - High performance reduced absorption - System calibrated and tested does not require any adjustment during installation   APPLICATIONS: Fresh water distribution under pressure on boats. Kitchens, showers, sinks, boilers, etc.   CONSTRUCTION: The standard configuration of the Control Press system is made with the ECOINOX, ECOJET, JET series el / pumps and includes: Sturdy techno-polymer pressure switch body - Stainless steel base on rubber antivibration mounts (on request) - Non-return valve

Cal Pump 305626012 Large Bracket S/MS580/900/1

Cal Pump MSUBM Nylon Bracket Fits All But 225 320 Nylon Mounting Brackets for 580, 900 and 1200 Pumps. Includes One Pair of Brackets.

Sherwood G-30-2B Engine Cooling Pump All Bronze   FEATURES Pump Body: Bronze Ports: 1" Hose Cam: Full Impeller: Neoprene Shaft Seal: Mechanical Drive: Bracket Mount Pulley Drive.   APPLICATIONS / CHARACTERISTICS Flexible Impeller Engine Cooling Pump. All Bronze version of Sherwood G-30-2.   Sherwood Engine Cooling Pump All Bronze for G30-2B G-30-2B, Chris Craft and Volvo Penta Model 350 16.80-18346    

Cal Msub SS Mounting Bracket Cal Pump SS Mounting Bracket for MS225 and MS320 Pumps. Stainless steel construction All metal

Cal Pump MS320P-6B SS/Bronze Pump 375Gpm 115V Cal Marine are certified to the following standards: UL, CE, ABYC and U.S. Coast Guard Premium stainless steel and bronze construction for longevity 115 Volts - 6ft power cord - 3 wire; black, white, green Suitable for fresh, salt or chlorinated water applications (max of 3-5 ppm) Can be used in hot water applications up to 110°F Extremely quiet operation Use submerged or in open air (below water level) Viton seals suitable for harsh marine applications 1/2" MPT Intake and 1/4" MPT Discharge Approximate dimensions: 3-3/4" x 4-1/2" One year warranty Pump Applications: Ideal for harsh marine applications

Cal Pump 305626005 Repair Kit for MS320P

Cal Pump 305626006 Repair Kit For MS580P