Cal MS-580-20-2B Pump 580Gph 230V 50/60 Cal Pump Centrifugal Pump, Stainless and Bronze Body, 580GPH No Flow Control, 230V 50/60Hz with 20 Foot Power Cord, 3/4" Male NPT Inlet and 1/2" Male NPT Outlet, Viton Seal, Can Run in Open Air or Submersed, For Fresh or Salt Water up to 110F, Can Be Used With Marine AC Units up to 24,000BTU, Approved for: UL, CE, ABYC and USCG. Includes 2 Nylon Mounting Brackets

Cal Pump MS-580-20 Pump 580Gph 115/120V 20'Cord Cal Marine Pumps are certified to the following standards: UL, CE, ABYC and U.S. Coast Guard Premium stainless steel and bronze construction for longevity 115 Volts - 20ft power cord - 3 wire; black, white, green ( NO PLUG ON END ) Suitable for fresh, salt or chlorinated water applications (max of 3-5 ppm) Can be used in hot water applications up to 110°F Extremely quiet operation Use submerged or in open air (below water level) Viton seals suitable for harsh marine applications 3/4" MPT Intake and 1/2" MPT Discharge Approximate dimensions: 4-1/2" x 6-1/4"  

Cal MS-900-6-2B Pump 900 Gph 220V W/Base Cal Pump Centrifugal Pump, Stainless and Bronze Body, 900GPH No Flow Control, 230V 50/60Hz with 6 Foot Power Cord, 3/4" Male NPT Inlet and 1/2" Male NPT Outlet, Viton Seal, Can Run in Open Air or Submersed, For Fresh or Salt Water up to 110F, Can Be Used With Marine AC Units up to 36,000BTU, Approved for: UL, CE, ABYC and USCG. Includes 2 Nylon Mounting Brackets

March 0150-0250-0100 Marine Pump LC-5M-MD March Pump’s industrial LC-5M-MD is an American submersible seal-less centrifugal magnetic drive marine pump. It is capable of generating a maximum flow of 15 gallons per minute at 2 feet, and its maximum head is 27 Feet (11PSI). The LC-5M-MD pump may be used submerged or not submerged. It is capable of 45,000 BTU a hour.   Max Flow: 54.9 LPM Max Head: 8.2 M Power: 0.093 KW   Electrical/Air: 230V 50/60Hz   230V Motor 6 Foot Cord, Submersible 60Hz: 1Ph 0.125HP/0.0093kW, 0.9AMPS, 3450 RPM 50Hz: 1Ph 0.125HP/0.0093kW, 0.5AMPS, 2850 RPM   Inlet: 1"FPT Outlet: 1/2"MPT   Submersible: Yes   Wet End: Polypropylene (Rear Housing, Impeller), Noryl (Front Housing) Buna N (O-Ring, Cooling Tube Seal), 316 Stainless Steel (Shaft, Cooling Tube), Carbon (Impeller Bushing), Ceramic (Thrust Washers), Ceramic Magnet Uses: Submersible or Open Air When submerged, the following is also in contact with the solution: Epoxy, Noryl, Cord Max Internal Pressure: 25 PSI / 1.7 bar Max Liquid Temperature: 130 °F / 54 °C Ignition Protected per SAE J1171 and ISO 8846: Rated IP67   This pump is capable of generating a maximum flow of 15 gallons per minute at 2 feet, and its maximum head is 27 Feet (11PSI).  It is capable of 45,000 BTU a hour.  The LC-5C-MD pump may be used submerged or not submerged. The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene,  Noryl, Buna N, Stainless Steel, Carbon, Ceramic, and Ceramic Magnet.  When submerged, Epoxy, Noryl, and the Cord are also in contact with the solution. The inlet connection is 1 inch female pipe thread, and the outlet is 1/2 inch male pipe thread. The standard motor is a 1 Phase 115V or 230V 0.125 Horsepower motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 130 Fahrenheit or 54 Celsius.     The pump is Ignition Protected per SAE J1171 and ISO 8846.  The impeller has a carbon bushing allowing the pump to run dry longer before suffering damage.  

March 0150-0040-1000 Magnetic Drive Pump AC-5M-MD March Pump’s industrial AC-5M-MD is an American seal-less centrifugal magnetic drive pump ideal for applications such as chemical recirculation, chemical transfer, and scrubber systems. It is capable of generating a maximum flow of 17 gallons per minute at 1 feet, and its maximum head is 27 Feet (11PSI). The pump is Ignition Protected per SAE J1171 and ISO 8846, and has extended run dry protection thru the use of a carbon bushing. It is capable of 48,000 BTU a hour.   Max Flow: 64.4 LPM Max Head: 8.2 M Power: 0.093 KW   Electrical/Air: 230V 50/60Hz   Motor 3 Foot Cord 60Hz: 1Ph 230V 0.125HP/0.093kW, 2.1 AMPS, 3450 RPM 50Hz: 1Ph 230V 0.125HP/0.093kW, 1 AMPS, 2850 RPM   Inlet: 1"FPT Outlet: 1/2"MPT   Wet End: Polypropylene (Rear Housing, Impeller), Noryl (Front Housing) Buna N (O-Ring), 316 Stainless Steel (Shaft), Carbon (Impeller Bushing) Ceramic (Thrust Washers), Ceramic Magnet Max Internal Pressure: 50 PSI / 3.4 bar Max Liquid Temperature: 190 °F / 87 °C Ignition Protected per SAE J1171 and ISO 8846: UL Listed Motor   This pump is capable of generating a maximum flow of 17 gallons per minute at 1 feet, and its maximum head is 27 Feet (11PSI).  It is capable of 48,000 BTU a hour.  The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Noryl,  Buna N, Carbon, 316 Stainless Steel, Ceramic, and Ceramic Magnet. The inlet connection is 1 inch female pipe thread, and the outlet is 1/2 inch male pipe thread. The standard motor is a 1 Phase 115V or 230V 0.125 Horsepower fan cooled motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheit or 87 Celsius.     The pump is Ignition Protected per SAE J1171 and ISO 8846.  The impeller has a carbon bushing allowing the pump to run dry longer before suffering damage.  

March 0125-0142-0100 Marine Pump LC-2M-MD March Pump’s industrial LC-2M-MD is an American submersible seal-less centrifugal magnetic drive pump. It is capable of generating a maximum flow of 5 gallons per minute at 1 foot, and its maximum head is 13 Feet (5.5PSI). The LC-2M-MD pump may be used submerged or not submerged. The pump is Ignition Protected per SAE J1171 and ISO 8846.  It is capable of 12,000 BTU a hour. Max Flow: 18.5 LPM Max Head: 2.7 M Power: 0.014 KW   Electrical/Air: 230V 50/60Hz   230V Motor 6 Foot Cord, Submersible 60Hz: 1Ph 0.025HP/0.019kW, 0.53 AMPS, 3450RPM 50Hz: 1Ph 0.18HP/0.014kW, 0.72 AMPS, 2850RPM   Inlet: 3/8"FPT & 3/4"MPT Outlet: 1/4"MPT   Submersible: Yes   Wet End: Polypropylene (Front Housing, Impeller), Nylon (Rear Housing) Viton (O-Ring), Buna N (O-Ring, Cooling Tube Seal), 316 Stainless Steel (Shaft, Cooling Tube), Ceramic (Thrust Washer), Ceramic Magnet Uses: Submersible or Open Air When submerged, the following is also in contact with the solution: Epoxy, Buna N, Cord Max Internal Pressure: 25 PSI / 1.7 bar Max Internal Temperature: 130 °F / 54 °C Ignition Protected per SAE J1171 and ISO 8846: Rated IP67

March Mag-Drive Pump 115/230V Cast Iron Flanged Ports Applications for the 830-CI Magnetic Drive Pump include hot water and hot oil systems.   March Pump's industrial 830-CI is an American seal-less centrifugal magnetic drive pump ideal for applications such as hot water systems. It is capable of generating a maximum flow of 15 gallons per minute at 11 feet, and its maximum head is 30.5 Feet (or around 13PSI). The standard wet end (the materials that come into contact with the solution) is composed of Cast Iron, Stainless Steel, Ceramic, Ryton/Teflon/Carbon, and Nitrile/Fibre. The inlet connection is a flange, and the outlet is a flange. The standard motor is a 1 Phase 115/230V 0.2 Horsepower fan cooled motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 150PSI, and the maximum liquid temperature is 250 Fahrenheit or 121 Celsius.     Unit System 60Hz 50Hz Max Flow 15 GPM 52.9 LPM Max Head 30.5 FT 6.5 M Power .2 HP .149 KW Electrical 115/230V 50/60HZ   Type Centrifugal Mag Drive Inlet Flange Outlet Flange Wet End Cast Iron (Front Housing), Stainless Steel (Rear Housing, Shaft), Ceramic (Thrust Washer), Ryton/Teflon/Carbon (Impeller), Nitrile/Fibre (Gasket)

Primetime Pump 230vac The Primetime Pump is a high performance self-priming 316 stainless steel centrifugal pump. The pump is ideal for Marine, Industrial, Agricultural or Commercial applications where suction lift is required.   Primetime features all 316 stainless steel components for superior corrosion resistance when pumping sea water or chemical compounds. A carbon / ceramic / Viton mechanical shaft seal is standard. Ports are 3/4” NPT with a 1/8” NPT fill port. The Primetime model is capable of 12 foot suction lift (3450 rpm). Marine ignition protected motors (ISO 8846).   SPECIFICATIONS: Flow…………………….Up to 21 GPM Head Feet……………Up to 23’ Housing………………316 Stainless Steel (Investment Cast) Cover………………….316 Stainless Steel Impeller……………..316 Stainless Steel Semi-Open Wearplate………….316 Stainless Steel Mechanical Seal..Carbon / Ceramic / Viton Bellows O-ring/Flapper…..Viton Weight……………...16 lbs    

Cal MS-1200-6B Pump 1200Gph 115V with Base and Cord Centrifugal Pump Stainless and Bronze Body 1200GPH No Flow Control 115V 60Hz with 6 Foot Power Cord 3/4" Male NPT Inlet and 1/2" Male NPT Outlet Viton Seal Can Run in Open Air or Submersed For Fresh or Salt Water up to 110F Can Be Used With Marine AC Units up to 60,000BTU Approved for: UL, CE, ABYC and USCG Includes 2 Nylon Mounting Brackets

Cal MS-900-6B Pump 900Gph 115V W/Base Cal Pump Centrifugal Pump, Stainless and Bronze Body, 900GPH No Flow Control, 115V 60Hz with 6 Foot Power Cord, 3/4" Male NPT Inlet and 1/2" Male NPT Outlet, Viton Seal, Can Run in Open Air or Submersed, For Fresh or Salt Water up to 110F, Can Be Used With Marine AC Units up to 36,000BTU, Approved for: UL, CE, ABYC and USCG. Includes 2 Nylon Mounting Brackets

Applications for the  March 1C-MD Magnetic Drive Pump include chemical transfer, photographic processing equipment, refrigeration systems, and water displays.      March Pump's industrial 1C-MD is an American submersible seal-less centrifugal magnetic drive pump. It is capable of generating a maximum flow of 2.3 gallons per minute at 0.25 feet, and its maximum head is 4.5 Feet (or around 2PSI).  The 1C-MD pump may be used submerged or not submerged. The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Buna N, Nylon, Carbon/Teflon, Stainless steel, and Ceramic Magnet.  When submerged, Epoxy, Noryl, and the SJT Cord are also in contact with the solution. The inlet connection is 0.25 inch male pipe thread, and the outlet is 0.25 inch male pipe thread. The standard motor is a 1 Phase 115V or 230V 0.005 Horsepower motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheit or 160 Celsius in open air, or 87 Fahrenheit or 71 Celsius if submerged. The March 1C-MD centrifugal magnetic drive pump is capable of handling fresh water, salt water, and mild chemicals.      Unit System 60Hz 50Hz Max Flow 3 GPM 9 LPM Max Head 4.6 FT 1 M Power .005 HP .003 KW Electrical 115V 50/60HZ or 230V 50/60HZ Submersible Yes   Type Centrifugal Mag Drive Inlet 1/4"MPT Outlet 1/4"MPT Wet End Polypropylene (Front and Rear Housing), Buna N (O-Ring), Nylon (Impeller), Carbon/Teflon (Thrust Washer), 316 Stainless Steel (Shaft), Ceramic Magnet Uses Submersible or Open Air When submerged, the following is also in contact with the solution Epoxy, Noryl, SJT Cord  

Applications for the 1U-MD Magnetic Drive Pump include chemical transfer, photographic processing equipment, refrigeration systems, and water displays.    March Pump's industrial 1U-MD is an American submersible seal-less centrifugal magnetic drive pump. It is capable of generating a maximum flow of 2.3 gallons per minute at 0.25 feet, and its maximum head is 4.5 Feet (or around 2PSI).  The 1U-MD pump must be used submerged. The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Buna N, Nylon, Carbon/Teflon, Stainless Steel, Cycolac, Delrin, and Ceramic Magnet.  When submerged, Epoxy, Noryl, Cycolac, Delrin, and the SJT Cord are also in contact with the solution. The inlet connection is a screen, and the outlet is 0.25 inch male pipe thread. The standard motor is a 1 Phase 115V or 230V 0.005 Horsepower motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheit or 160 Celsius in open air, or 87 Fahrenheit or 71 Celsius if submerged. The March 1U-MD centrifugal magnetic drive pump is capable of handling fresh water, salt water, and mild chemicals.      Unit System 60Hz 50Hz Max Flow 3 GPM 9 LPM Max Head 4.6 FT 1 M Power .005 HP .003 KW Electrical 115V 50/60HZ or 230V 50/60HZ Submersible Yes     Type Centrifugal Mag Drive Inlet Screen Outlet 1/4"MPT Wet End Polypropylene (Rear Housing), Buna N (O-Ring), Nylon (Impeller), Cycolac (Cover), Carbon/Teflon (Thrust Washer), Delrin (Screen), 316 Stainless Steel (Shaft), Ceramic Magnet Uses Submersible or Open Air When submerged, the following is also in contact with the solution Epoxy, Noryl, Cycolac, Delrin, SJT Cord    

March 1A-MD-1/2 Mag Drive Pump March Pump's industrial 1A-MD-1/2 is an American submersible seal-less centrifugal magnetic drive pump. It is capable of generating a maximum flow of 3 gallons per minute at 0.25 feet, and its maximum head is 4.5 Feet (or around 2PSI).  The 1A-MD-1/2 pump may be used submerged or not submerged. The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Buna N, Nylon, Carbon/Teflon, and Stainless Steel.  When submerged, Epoxy, Noryl, and the SJT Cord are also in contact with the solution. The inlet connection is 1/2 inch smooth, and the outlet is 1/2 inch smooth. The standard motor is a 1 Phase 230V 0.005 Horsepower motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheit or 160 Celsius in open air, or 87 Fahrenheit or 71 Celsius if submerged. The March 1A-MD-1/2 centrifugal magnetic drive pump is capable of handling fresh water, salt water, and mild chemicals. To determine if the March 1A-MD-1/2 is suitable for your application, please contact March Pump.   Perfect for Applications Including Applications for the 1A-MD-1/2 Magnetic Drive Pump include chemical transfer, photographic processing equipment, refrigeration systems, and water displays.   Great for Chemicals Including The 1A-MD-1/2 has pumped Acetone, Ammonium Chloride, Ammonium Chloride, Ammonium Hydroxide, Citric Acid, Ethylene Glycol, Magnesium Nitrate, Potassium Carbonate, Sodium Borate, Fresh Water, Salt Water, and many more chemicals.   Inlet: 1/2"OD Outlet: 1/2"OD Wet End: Polypropylene (Front Housing, Rear Housing, Impeller), Buna N (O-Ring), Carbon/Teflon (Thrust Washer), 316 Stainless Steel (Shaft) Uses:Submersible or Open Air When submerged, the following is also in contact with the solutionEpoxy, Noryl, SJT Cord   P/N 0115-0007-0700 (230V)

March 2CP-MD 230V Pump The most common application for the 2CP-MD Magnetic Drive Pump is for marine air conditioning and fountains.   March Pump's industrial 2CP-MD is an American submersible seal-less centrifugal magnetic drive pump. It is capable of generating a maximum flow of 5 gallons per minute at 1 foot, and its maximum head is 13 Feet (or around 5.5PSI).  The 2CP-MD pump must be used submerged. The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Viton, Stainless Steel, Ceramic, and Ceramic Magnet.  When submerged, Epoxy, Buna N, and the Cord are also in contact with the solution. The inlet connection is 0.375 inch female pipe thread and 0.75 inch male pipe thread, and the outlet is 0.25 inch male pipe thread. The standard motor is a 1 Phase 115V or 230V 0.028 Horsepower motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 130 Fahrenheit or 54 Celsius. The March 2CP-MD centrifugal magnetic drive pump is capable of handling fresh water, salt water, and mild chemicals.   Max Flow 250 GPH 18.5 LPM up to a 6000 BTU Air Conditioner Max Head 13 FT 2.7 M Power .028 HP .021 KW Electrical 230V 50/60HZ Submersible Yes   Type Centrifugal Mag Drive Inlet 3/8"FPT & 3/4"MPT Outlet 1/4"MPT Wet End Polypropylene (Front and Rear Housing, Impeller), Viton (O-Ring), Stainless Steel (Shaft), Ceramic (Thrust Washer), Ceramic Magnet Uses Submersible Only When submerged the following is in contact with the solution Epoxy, Buna N, Cord

March LC-2CP-MD Mag Drive Pump 230V The most common application for the LC-2CP-MD Magnetic Drive Pump is for marine air conditioning and fountains. This pump will handle up to a 6,000 BTU Air Conditioner. March Pump's industrial LC-2CP-MD is an American submersible seal-less centrifugal magnetic drive pump. It is capable of generating a maximum flow of 5 gallons per minute at 1 foot, and its maximum head is 13 Feet (or around 5.5PSI).  The LC-2CP-MD pump may be used submerged or not submerged. The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Viton, Stainless Steel, Ceramic, and Ceramic Magnet.  When submerged, Epoxy, Buna N, and the Cord are also in contact with the solution. The inlet connection is 0.375 inch female pipe thread and 0.75 inch male pipe thread, and the outlet is 0.25 inch male pipe thread. The standard motor is a 1 Phase 115V or 230V 0.028 Horsepower motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 25PSI, and the maximum liquid temperature is 130 Fahrenheit or 54 Celsius. The March LC-2CP-MD centrifugal magnetic drive pump is capable of handling fresh water, salt water, and mild chemicals.   Unit System 60Hz 50Hz Max Flow 5 GPM 18.5 LPM Max Head 13 FT 2.7 M Power .028 HP .021 KW Electrical 115V 50/60HZ or 230V 50/60HZ Submersible Yes   Type Centrifugal Mag Drive Inlet 3/8"FPT & 3/4"MPT Outlet 1/4"MPT Wet End Polypropylene (Front and Rear Housing, Impeller), Viton (O-Ring), Stainless Steel (Shaft, Cooling Tube), Ceramic (Thrust Washer), Ceramic Magnet Uses Submersible or Open Air When submerged, the following is also in contact with the solution Epoxy, Buna N, Cord